c'est dommage que l'on se sache pas ou il achète son matos

Depth adjustment can be stopped at any position by inserting a piece of wood into the linear shaft. For fine adjustment, just adjust the amount of protrusion of the drill. This method gives an accuracy of ±0.2mm.

GOOD MODIFICATIO

Considered. But springs are useless without a lever handle. A weak spring doesn't make sense. If the spring is strong enough, it will be difficult to push the drill by hand.

@@jisakukobo accepted! 🙂

Do a search for "kanetec MB-PG" for the type used above ... looks like you can buy them most places (price depends on size) or you could try making your own ... relatively simple mechanism using a few magnets 👍

Thank you. Product links are posted on the plan. I sell plans and use the money to test new ideas. It would be helpful if you could purchase a plan.

savez vous ou il achète son matos svp

Только хотел это же написать.

Про какой сверлильный станок вы говорите? Можете привести пример небольшого станка ?

It's like this. amzn.to/3PmL9hm I only know Japanese names. If you like my vides, please share the video with your friends and on social networks. I am happy to have different people watch it.

@@jisakukobo thanks a lot for the info!

@UClArzi-fOX93nVr5xgY8Fsg Great! thanks for the tip, thanks to your information and those of JSK I was able to find them, frankly here in Italy I had never seen them, not even from other youtubers

Thank you. Product links are posted on the plan. I sell plans and use the money to test new ideas. It would be helpful if you could purchase a plan.

Автоматический керн, все инструменты

ukposts.info/have/v-deo/mWKcfYB7n56L05s.html

Thanks. This is helpful.

やはり道具が揃わないと金属加工が難しいと思います。 やっていることは単純な事なんですけどね・・・

Hello sir, excuseme

@@Zie_carpentry yep

@@burakgok 😍😍

No problem. The manual for the magnetic base has instructions for points that can be additionally machined. I don't think there are many youtube channels that are investigating and working on such things.

Yes

I cannot find a 1/2" (13mm) chuck version anywhere.

👍👍

I have never heard of such a story. On what basis did you think so?

@@jisakukobo I thought that batteries are affected from magnets

ドリルチャックはWEBマニュアルにリンク付きで記載しています。 まずはWEBマニュアルをご一読ください。 また、コメント欄をサポートに使用しないでください。高確率で埋もれてしまうので気が付きません。 このコメントも偶然見つけたので以降返信できるとは限りません。

ありがとうございます。確認します。

👍👍✅

Do you mean linear or ball bearing? A linear bearing would normally be held on with a circlip holding it into the pillow block. But @8:07 it's the ball bearing.

@@aries6776 no. The linear block bearing (looks like a SCS16UU) and it normally slides up and down the linear shaft that it's on. But his is held in place. Normally a stop collar and thrust bearing are used in a situation like that... but I dont see it. So, something is keeping the bearing from sliding up/down the shaft, while giving it a free range of rotation, thus allowing the chuck to spin freely. But even then, the linear bearings in a UU style wouldnt hold up well under a spinning design where the shaft rotates inside the bearings. So, I'm just confused. Lol

@@carterscustomrods If you're talking about the chuck spindle, it's not a linear bearing. It's a mini lathe kit from China.

@Darren Garden ughhh those are junk! Plus only 3/8" chuck. I was going to make with 1/2" chuck, with 1/2-20 threading, but I can't find a smooth straight shaft with that thread. :( Kind of a bummer that JSK didn't make it more effective. A portable drill press like this is no good if the chuck you use us junk.

👍👍✅

На али такие есть. Ссылка обычно удаляется.

Yes

Мои поздравления ✨🥇✨

Thanks! Product links are posted on the plan. I sell plans and use the money to test new ideas. It would be helpful if you could purchase a plan.

Только русские по-моему заметили, что нужна возвратная пружина! Я тоже такого мнения!

ThanK you 👍❤️ ❤️❤️

I wish I had a board like that...

True, and that’s what I use. However, when I’m drilling and tapping many holes on steel this would be nice.

I originally made this drilling machine for the purpose of drilling holes in large plates of metal. jisaku-koubou.com/3582 When I used the tool in my woodworking work, many people asked me how to make it. Therefore, this drill press has been improved so that anyone can make it.

yes. This is because they use cheap chucks made in China.