3 Ways to Add an Outlet In a Finished Room

День тому

You can add an outlet or receptacle to any finished wall or room with these three methods! Please not that this applies to drywall only. #outlet #electrical #wiring
🎬 CHECK OUT THESE RELATED VIDEOS! 🎬
• How to Caulk Like a Pro: • How to Caulk Like a Pro
• 6 MISTAKES DIYers Make When Wiring Outlets: • 6 MISTAKES DIYers Make...
• Should Your Outlet Ground Face Up or Down?: • Should Your Outlet Gro...
Check out Everyday Home Repairs at / everydayhomerepairs
📦 PRODUCTS IN THIS VIDEO 📦
Links below are affiliate links:
* Milwaukee Fastback Knife Set: HOME DEPOT (Best Price): homedepot.sjv.io/AoN00D AMAZON: geni.us/qEiF
* Trim Puller: geni.us/3BrKA9
* 6” Drywall Knife: geni.us/J1Ys13m
* 13” Pry Bar: geni.us/W1zVR
* Franklin Stud Sensor: geni.us/3Ldol
* 1 1/2” Painters Tape: geni.us/v3ngAmo
* Ridgid Multi-Tool: HOME DEPOT: homedepot.sjv.io/WDkXXn
* Milwaukee Multi-Tool: geni.us/aS7RKO
* Oscillating / MultiTool Blade Set, includes metal cutting blade: geni.us/OVGh3b
* Milwaukee Jab Saw: HOME DEPOT: homedepot.sjv.io/EaNbbn
* Milwaukee Insulated Screwdriver set with ECX bit: HOME DEPOT: homedepot.sjv.io/b3obb6
* Outlet tester with LED screen: geni.us/MziA1
* Commercial grade outlets: HOME DEPOT: homedepot.sjv.io/ORxBBG
* 16” Diablo 3/4” Speed Tip Drill Bit: HOME DEPOT: homedepot.sjv.io/3PNAPA
* 1.5 x 2.5” Nail Plates: geni.us/5R66
* Depth Adjustable Electrical Boxes: HOME DEPOT: homedepot.sjv.io/MXLnXN
* Screw Mount Electrical Boxes (geni.us/OS7tvQ7)
* 14/2 Romex Wire: geni.us/9VieE
* 12/2 Romex Wire: geni.us/uTFUFd
* Milwaukee 9 Inch Seven in Ones: homedepot.sjv.io/KeNKez
* Wire Nut Variety Pack: geni.us/Wdj0A
* Wago 221s (I LOVE these!): geni.us/i5XaL
* Knipex Wire Strippers: geni.us/OTAm
* Flush Cut Nail Cutters: geni.us/qLMZUH9
* Ridgid 18 ga Brad Nailer Cordless: homedepot.sjv.io/LPNaPO
* Walabot DIY 2: geni.us/RzvxAUb
* Dewalt Handheld hack saw: HOME DEPOT: homedepot.sjv.io/zaVgg7
* Milwaukee Handheld Hack Saw: geni.us/3ajef
* Metal Cutting Saw Blade for Multi-Tool: geni.us/R3hno
* Klein Wire Puller: AMAZON ($10 Cheaper): geni.us/jvSoA HOME DEPOT: homedepot.sjv.io/QOQPOz
* Diablo 5/8”, 3/4”, 1” Speed Tip Drill Bit: geni.us/vwrZ
* Eagle 54” 3/4” Drill Bit: geni.us/kL7v
* Ridgid SubCompact Brushless Drill & Driver Combo (I LOVE this set!): homedepot.sjv.io/ojYB9
Links above are affiliate links, which means you pay the same price as always but we make a small commission, which helps out our channel - so thanks!
👍 WANT TO HELP SUPPORT THIS CHANNEL? 👍
Become a channel member! Hit the "Join" button or head to / @lrn2diy
Support us on Patreon: / lrn2diy
👕 LRN2DIY SHIRTS, HOODIES & MORE 👚
lrn2diy-shop.fourthwall.com/
📸 MY FILMING GEAR 📸
Here’s everything I use to film my videos, including cameras, lights, microphones and more: kit.co/nilsynils/my-filming-gear
🕶 SOCIAL MEDIA 🕶
Facebook: / lrn2diy
Instagram: / lrn2diy
Twitter: / lrn2diy
TikTok: / lrn2diy
📲 MORE DIY GOODNESS 📲
Check out our many projects and plans at
lrn2diy.com
📲 WANT TO LEARN MORE ABOUT 3D PRINTING? 📲
All things 3D Printing at The 3D Printing Zone
/ the3dprintingzone
📚 TWO FREE AUDIOBOOKS! 📚
To get two free audiobooks from Audible, just follow this link: goo.gl/QGFC4Q
00:00 Method 1: Behind Baseboard
11:20 Method 2: Through the Attic or Crawlspace
18:26 Method 3: Drywall Strip

КОМЕНТАРІ: 329

@Bigfoot14000 Рік тому

A tip for you: Don't remove the coil of Romex from its plastic packaging, as you did in the video. Instead, leave it in the plastic and pull cable from the center of the coil. This keeps the coil neat and untangled.

@LRN2DIY Рік тому

Yeah, I had it in there for a months but it kept coming out so I just gave up eventually. I'm just waiting for the first big knot to show up and I'll have to spend an hour figuring it out. Fingers crossed that doesn't happen.

@TomCee53 Рік тому

This is a personal choice. I’ve had very little problem with coils of wire not in the plastic package. In fact, my preferred method is to remove the plastic package and roll out the wire smoothly from the outside as opposed to pulling from the inside where it will twist with every turn. My preference is that the wires look smooth as they are stapled to the ceiling or pulled through holes in floor joists.

@heathenkill1 Рік тому

Yes it works well like that.

@k2line706 Рік тому

Lol horrible tip. Now you have massively twisted wire.

@jovetj Рік тому

And always wire outlets with 12 AWG.

@andyd3063 Рік тому

I am grateful for all of your clear, detailed videos, especially when you offer up a few options since I always expect my situation to not be identical to the lone approach presented. If I'm honest, I sometimes feel overwhelmed by a "how in the heck will I do X without cutting 17 holes in the drywall?!" fear and your approaches are well thought out and minimally disruptive and counter that for me, so thank you! (Also, I've been hacking away at electrical stuff in my house for a couple decades and until you casually mentioned it, it never dawned on me how pigtailing in new outlets keeps the circuit working even if that outlet fails! Thanks, too, for sharing that!)

@crabwalk7773 Рік тому

I am glad you covered the options together - made for a comprehensive video. Thank you.

@BlackSmokeDMax Рік тому

Props for showing your "ooops!" and not cutting that out, and just moving to a different outlet and starting over.

@Jwaxenbaum602 Рік тому

This has to be the most thoroughly explained, clear and well put together instructional house DIY video I've ever seen.

@foesfly3047 Рік тому

You really are so good at this. Your trade methods and craftsmanship are excellent, your scripting and video techniques and editing are also exceptional and your presentation is so good in every way- appearance, verbal delivery and manner; you’re just very relatable- and to a broad audience, I believe. Thanks for doing what you do.

@LRN2DIY Рік тому

Wow - that's so very kind of you! Thank you so much and have an awesome day!

@keithfailmezger1596 Рік тому

another good trick to know where to drill in the attic .. is to take a coat hanger and straighten it out , then use a drill and put one end in the drill and go up next to the wall where you need to drill and drill that coat hanger up in the ceiling next to the wall , when you go up in the attic you can see the two feet of coat hanger sticking up through the insulation ,, it leave such a tiny hole when done

@LRN2DIY Рік тому

Very true. I actually filmed all of that for this video (had the hanger chucked in the drill) but decided to cut it out since the video was so long already and I figure most folks will be able to use the measuring method, but I'm always on the fence about how much to leave in or take out.

@llapmsp 8 місяців тому

Excellent video on three great ways to do additions in wiring. Thanks for sharing.

@kevinh5983 Рік тому

For #3 you can use a California drywall patch to patch the drywall and not have to deal with sticks. I learned how to do that recently and I'll never make small patches with wood supports again.

@Gruuvin1 Рік тому

I love that you used your tester for correct wiring AFTER you reattached the drywall and baseboard. That's how I would've done it too!

@manny9323 Рік тому

Can’t tell if this is sarcasm. But yeah if the wiring’s wrong it can be fixed in the box so there’s no real reason to test before finishing.

@Gruuvin1 Рік тому

@@manny9323 sometimes. Not always

@LeverPhile 10 місяців тому

Lol ...

@btd2516 Рік тому

You can get oversize outlet and switch plates at Lowes and Home Depot to cover "boo-boos" when cutting box holes like in method #2. Glad you showed all 3 methods.Good video. Thanks!

@miguelperez2369 Рік тому

Your first method is my go-to every time.

@MarlaHaynes 8 місяців тому

Thank you so much. I just had to replace my outlet in my bedroom and I'll redo it to make sure about the silver and brass sides. After, I can add another outlet to my room. I really appreciate this. My uncle who does this has moved far away and I have to do things myself. Again..... THANK YOU

@swcheshier61 Рік тому

I just subscribed. Love your video. Straight to the point, very well thought out, very thorough. Thank you.

@saulrodriguez7258 Рік тому

Thank you very much, very informative, I enjoy watching and learning from your videos. Keep up the great work.

@robertgregory2618 Рік тому

Back before the magnate thing I used to use very small chain. Hook on wire in attic, tape it so it wouldn't get caught on something and then used a piece of wire, made a hook on the end of it to hook on to the chain down at the box. Didn't have to take box out, just made another hole in top of box and fished it in. Made sure I was behind or in front of insulation. You could tell if it was going down by shaking the chain and by the weight of the chain. It took a bit of skill but that's all we had back in the day.

@edwardmoran1739 10 місяців тому

Wow that Klein magnet tool is fabulous. Thanks.

@jerrylittle7797 8 місяців тому

Awesome video. Love the 1 1/2 tape trick!

@blackhorse2947 Рік тому

This is a project I want to do as well. Not sure which method I will use. Here in Oklahoma presently it’s 105 degrees and i’m sure my attic is the temperature of the sun, but thank you for this video and information, very well done.

@LRN2DIY Рік тому

Thanks and best of luck on yours! The attic was insanely hot and definitely the worst part of this project but my timing was definitely not the best.

@partsdave8943 Рік тому

I used a Right Angle drill adapter in a tight spot between studs. Worked perfectly with my 6 inch Speed Bit.

@LRN2DIY Рік тому

Good call! I actually have one but didn't think to use it.

@walkerjw81 Рік тому

I would have never thought to take out the baseboard. This is great. I was wondering about moving to either side of studs on a finished wall. Removing the baseboard makes it easier to replace and patch up with zero notice. Great clip.

@jimonthecoast3234 9 місяців тому

Now the base has two ugly seams. This is a hack job

@walkerjw81 9 місяців тому

@@jimonthecoast3234 not really though.

@vendright 4 місяці тому

Very helpful, thanks for taking the time to do this

@tommissouri4871 Рік тому

3:25 -this is a good idea most miss. When we moved my parents' house 47 years ago, I wired the basement rooms such at power for lights and outlets were different circuits and the rooms were split so that not all were out at once. It gets very dark in a basement if all go out. Also, if you need to shut off power for work in a room, you still had power close that normal extensions worked for the tools.

@stixinst5791 Рік тому

Also laying a live cable in a pvc/metal pipe all the way around every room. Saves you the headache of using a source outlet

@HankBaugh 3 місяці тому

Great job. I have an old house that still has some ungrounded wiring to replace. I will probably be able to use the baseboard method. Probably will buy one of those Kein wire pullers just in case.

@aarondixon2244 8 місяців тому

With method #1, be careful about double bottom plates (3” high) on your wall, especially when using standard 3 1/4” baseboard. You would not have enough space to drill through the studs. You might be able to get away with it if the baseboard has been raised off the floor 1/2” to account for carpet thickness, but otherwise it would not work. This would be an issue in exterior walls on most wood framed homes, but could even come up in some interior walls. In Florida, for example, many homes are built on concrete slabs, with double bottom plates on all interior walls - the bottom bottom plate being pressure treated. They have concrete block exterior walls and no basements, so the only way to add an outlet like this without cutting and patching drywall would be to go up into the attic.

@TheFatbutterpancake 3 місяці тому

thanks ive consulted this video several times. Well done easy to follow.

@jackdolphy8965 Рік тому

Your mention of the ecx is something many of have not known about from our beginnings as diy-ers or even pros. Super excellent bit to have!

@JosePedroFilipeCuriousTech Рік тому

I like this type of videos just to know how things “could have been” because here where I live we don’t use drywall to build walls. We use bricks which makes all these methods inappropriate 😊 But, has I said, nice video 👍🏼

@greekboydinos Рік тому

excellent instruction, thank you for sharing

@Gracenote35 Місяць тому

I’m an electrical engineering student in college. I don’t have my own place, let alone any need to do this. Did I still watch the entire thing? Yes. Yes I did. Great video!

@jaycustin7002 Рік тому

Some irony here... one of the first of your videos I watched covered (a) why to NOT use the wire nuts you have in this video and (b) the auto stripper. Aside from that... yet another amazing video. If I could give you two thumbs up I would.

@user-ol8zt5ep6u 7 місяців тому

Homesickness became contagious in the young campers' cabin.

@larryborshard7824 2 місяці тому

Love your videos, Nils. I'm always learning something. Apologies if this has already been mentioned, but don't you want to check your wiring BEFORE you reinstall the dry wall and molding,.in case you need to correct something without tearing the molding and sheetrock back out? Keep up the great videos. I'm going to keep on watching!

@robertcampain612 Рік тому

Very informative!! Thanks for posting!!

@stinky3toes209 9 місяців тому

I recommend that you mark the studs with painters tape (no tape residue) before you remove the baseboard to prevent damaging the drywall.

@davidward3991 8 місяців тому

I used a tape measure sent up to the attic to attach the romax cable and my father in law was so amazed that he had never thought of that. It took us 30 min to pull 3 wires so that we could run it to my workshop.

@ryanyoder7573 7 місяців тому

Cool idea thanks for sharing

@vilo3454 Рік тому

Finally, someone did an outlet add that is not the easy directly above outlet add

@ViniciusDellAglio 3 місяці тому

Very very nice video, thanks for sharing it with the community!

@theMightyWhytey 9 місяців тому

Thumbs up for giving the thumbs up for past Nils… that guy deserves it

@offertunatea Рік тому

I've seen wire protect ring that you simply put the wire through the ring and put the ring into hole of the stud. That makes more room for nailing drywall onto the stud.

@ikkuranus Рік тому

I didn't know a stud finder like the one you have existed. I absolutely hate the typical ones where they don't illuminate the entire stud all at once.

@johnknightiii1351 Рік тому

Drop a chain down the box then attach it to the romex to pull it up through the box, it makes it super easy.

@notasheep5888 Рік тому

Thanks for you videos, and following code. Installing outlet on a wall by cutting drywall behind baseboard in closet on the other side of the wall. How can I install nail stops without taking baseboard off the other side, ie both sides of the wall? Thanks!

@TomCee53 Рік тому

The magnetic wire puller is interesting, but i usually use a fiberglass rod set to pull from attic or basement, especially with insulation.

@hankkline7300 Рік тому

I use a piece of #6 ground wire, it will punch right through an insulated wall then tape your romex to it.

@duggiemoe 3 місяці тому

That's the greatest looking stud finder I've ever seen!!

@JoshSongz684 Рік тому

Great video. I’ve never seen method 1 before. Going to try that next time. And I definitely need to get me one of those magnets.

@johnburns2940 Рік тому

Thanks fella, lots of good stuff here to absorb.

@clarkwhicks Рік тому

Dude what a wonderful and informative video thanks

@topperdude2007 Рік тому

Glad to see this video - I am in the process of finishing my basement as well and found your basement related video(s) quite helpful especially the ones related to options for transmitting A/V from receiver to projector. One quick question - I noticed in this video you mentioned about the insulation for sound isolation. I am also planning to add insulation to my inside walls for the same purpose - however, folks (contractors / handymen) locally seem to indicate fiberglass insulation does not work quite as well for sound isolation as compared to mineral wool. However - as you might know - mineral wool is quite bit more expensive compared to fiberglass. I would appreciate your feedback on how well fiberglass insulation has worked for you for the purpose you stated in the video ("kids sleeping while the home theater is cranked up")? Thanks for any input. 👍 P.S. I will also be using this video (along with Scott's video) as reference for tying into existing switch to add an outlet for heated towel rack.

@LRN2DIY Рік тому

Very cool that you're working on your basement! So my experience with the insulation for sound is that you get what you pay for. It definitely helps - even just the fiberglass - but it doesn't block out as much as rock wool. I think we paid about $1500 to insulate our entire 1950 square foot basement (including 6-8" thick ceiling fiberglass) so it was well worth it. Keep in mind that was several years ago. Good luck on the basement and the outlets too!

@topperdude2007 Рік тому

@@LRN2DIY Thanks for the quick reply - not sure why UKposts notification takes so long to show up. Glad to learn about your experience. with sound attenuation using fiberglass. My challenge since starting work on the basement finish back in summer of 2020 and wrapping up framing in couple days (~1200 sq ft basement area) was to get contractors out for HVAC, electrical (since we needed an additional breaker box added). Once the electricians were done - in Spring 2021, we have struggled with getting the insulation material due to supply chain shortages (anytime we stopped by the big box stores, we were told the contractors used to take any consignments coming on). Furthermore, things were complicated since most videos I have seen regarding mineral wool are installing between I-beams 16 inches on center whereas our ceilings have floor trusses that are 24 inches on centers and mineral wool in that size is even harder to come by. Anyway, now with price hikes - fiberglass is almost twice the cost of what it was prior to pandemic - the gap between cost for fiberglass and mineral wool is even less. So even if we go with mineral wool, we need to make sure it is installed properly. Thanks again for sharing your experience.

@user-eh2rl5xk9o 7 місяців тому

We could never learn to be brave and patient if there were only joy in the world.

@kyungrix1112 Рік тому

I have converted many of my outlets in my house to double outlets for 4 total outlet spots per. I use a sawzall to cut the nails on the original boxes, I just feel cutting nails with the multitool damages the blades too fast

@joshuaychung 5 місяців тому

In Illinois (at least Northern Illinois by Chicago), I think you have to run metal conduits behind the walls. Even exposed, you have to run the metal clad armord cables. I guess I can somehow get sections and connect them somehow...

@coydever7748 Рік тому

Great info. Just a bit of advice, remove that huge conductor on your finger when working with electricity.

@prant8998 Рік тому

Drop cloth?

@johnmiranda1341 Місяць тому

nicely done and love the Storm Trooper

@suzylarry1 6 місяців тому

the green screen view has surpassed th HOW TO with guess and by golly to a conformation on how to . Very well displayed

@michaell6645 Рік тому

Absolutely helpful first way!! Wouldn’t it be better to test power before putting wall back together? My luck I would have to take off twice 😂

@pargolf3158 Рік тому

If there was a problem with the power, he would not need to pull the wall back off since the cable is already run from outlet to outlet. The problem would lie within the outlet box itself.

@JVinOlathe Рік тому

I agree. I always do all the connections first and test before putting the receptacles in the box. Once everything tests ok, I assemble the receptacles and do a final test before putting the covers.

@nathanielr9073 Рік тому

Subbed for the green screen wall, never seen someone do that before!

@johnsee7269 Рік тому

We always used pigtails and 12-2; even on lighting citcuits. Nowadays that might be less feasible... Wired many cable heat, 220(240), ceiling panels with our 12-2 to the manufacturer's 14-2...

@gaylanbishop1641 9 місяців тому

At 6:35, how did you feed the cable in through that little hole in the outlet box?

@Unknown--error Рік тому

What is that attachment on the bottom of your ridgid drill? Looks like a magnet or bit holder of some sort. Got a link?

@LiesOfJoe Рік тому

wow never thought of doing it this way before.

@HughD Рік тому

Nice job! I'd like to see you do one showing putting an outlet on the other side of an interior door facing the same interior space.

@LRN2DIY Рік тому

Thanks! If you have attic or crawl space access, it’s the same process as shown. If not, it’s a lot of drywall cutting and patching.

@HughD Рік тому

@@LRN2DIY Thanks for the quick response, but unfortunately the roof slopes down over this area and makes it almost impossible for a normal-size person to get to it. I see Home Depot has some quarter-round with a channel for wiring, but am not sure if that is ok for electrical wiring...they show it being used for HDMI and USB power wiring. This door has a threshold as it goes to a screen porch from a bedroom so that would help.

@LRN2DIY Рік тому

@@HughD It’s up to you, of course, but it’s against code to run anything but low voltage wiring in that way, so HDMI and such are ok but not 110v for wiring outlets unfortunately.

@HughD Рік тому

@@LRN2DIY I thought that might be the case. Thanks again!!!

@evictioncarpentry2628 Рік тому

Go through the bottom. You surely have a basement or crawl space to access it.

@noahholt482 Рік тому

I do the same thing wit our patching. Cut the hole for box in center and then drill left and right. . Then drill through the side of each existing box and run fish tape.

@rashellyohn5128 2 місяці тому

Thank you for your knowledge giving me hope. I don't trust that my wires are safe after my son melted an outlet so bad it blew open the whole side of the outlet. I am afraid that the romex has melted and is exposed at points not seen. This house was built in the early 50's and the wire gauge is larger than 12g and will not wrap around any up-to-date outlets and also there is nothing to work with. No 6" loop. The breaker box I know I need to get an understanding of what breakers handle what amount of amps per breaker so as not to make the same mistake that I think the prior owner(s) have made by overloading a breaker. But to assume that it is at the right amps on this particular breaker I will need to rewire from the box and daisy chain to all the 4 outlets starting with the closet to the breaker and move on to the next. Where would I go when It comes to the threshold of the front door and going from one wall to the next. Can I just disconnect the old wire and leave it in the wall and rewire it along the base bords cutting the sheetrock in the strips as you have done. Please and thank you for giving me some advice and how to get started.

@bcmiller1100 Рік тому

"i'll head up into the attic which is approximately 4621 degrees" 😂😂

@spirod2657 Рік тому

Quite interesting. I like the second method better. I'm not an electrician but I'm pretty sure that here for us in Australia, any mains wiring that goes horizontal needs to be outside the wall, visible in a conduit. Only verticle wrining can hide inside the wall. Otherwise great video. Enjoyed it.

@hemi4722 Рік тому

I don't know about Australia but Canada we have mains wires go horizontal, as long as it's protected and supported every few feet which it is but running through the CENTRE of the stud. That parts important.

@TheNewGreenIsBlue 2 місяці тому

Nice video. I may recommend stripping the romex and taping the end to fish into the box. You'll get a cleaner cut inside the box and it's easier. Especially with such a small run. That being said, the insulation might be a bit of an issue in that case.

@efthegop8000 Рік тому

Pro tip. Shorter wires and longer pigtails will let the wires fold easier into the box

@LzysGraphics Рік тому

yuck. you can't possibly be suggesting cutting the wires short...

@jovetj Рік тому

Well, definitely longer pigtails. Want 6 inches at least on those, too.

@paulpugh2480 8 місяців тому

You can chisel out a small place to accommodate the Romex in front of the stud and then cover it with your nail plate and don't drill a hole in the stud weakening the stud.

@paulpugh2480 8 місяців тому

Neatly done.

@michaelmcdonough1989 Рік тому

Is there not a code that you have to secure the romax to the stud within so many inches above/below the outlet?

@LRN2DIY Рік тому

That applies to new installs. Here's what 334.30 states: Unsupported Cables. Nonmetallic-sheathed cable shall be permitted to be unsupported where the cable: (1) Is ﬁshed between access points through concealed spaces in ﬁnished buildings or structures and supporting is impracticable. (2) Is not more than 1.4 m (4 1 ⁄2 ft) from the last point of cable support to the point of connection to a luminaire or other piece of electrical equipment and the cable and point of connection are within an accessible ceiling

@michaelmcdonough1989 Рік тому

@@LRN2DIY Thank you

@sparkyheberling6115 Рік тому

I've read that it is safer to orient the plug with ground up. Does NEC have a preference?

@MarkJaquith Рік тому

What about using a flex bit to drill sideways through the studs from one box to the other? Probably going to be tricky going through four studs, but one or two should be doable (with two, you could drill them individually from each side, after removing the existing outlet box like you showed).

@jonathanladd845 Рік тому

You can actually get them that have sections that make them multiple feet long and they have a little hole on the end of the bit to hook a pull wire through and then from the pull wire you can attach your romex and pull it through. Literally the only extra holes in your wall is the one for the new box. So much easier and faster.

@sparkyheberling6115 Рік тому

Do you have a video for installing receptacles in plaster walls?

@tonygil4372 5 місяців тому

Thank you for this video.

@pauljohnfox Рік тому

How is this done with brick, block, or cement walls? I’m imagining just grinding out a massive channel to run the wires and having to patch and paint after. There is also an absurd mix of poorly done surface mounts (some are grounded) and the original cloth wire two prong outlets. How do I shove it all into the wall AND add ground to the older circuits? Is it possible without hiring a pro?

@ChevyDude Рік тому

I just use one of those Stickers that look like an outlet. Much easier... 🤣

@johnsee7269 Рік тому

😂

@PeymanSayyadi Рік тому

Great video, thanks for sharing.

@akbychoice Рік тому

Caution when drilling near the bottom of the stud, drilling into a nail could be an issue.

@hiiamhuman771 Рік тому

this is in branzys playlist

@mikeheller1225 14 днів тому

You can eliminate worry about the new Romex getting damaged by using Smart Shield (get at Home Depot) instead of nail plates.... in this application, would be perfect!

@mjcompanies Рік тому

You mentioned you can deal with fire blocks. Can you share how to do that? I would like to add an outlet up higher on the wall for a TV, but I am worried about the fire block and not sure how to get through that without creating a patch job.

@MoneyManHolmes Рік тому

I would use the cutout for the new receptacle box and try to drill through the fire block from above. Maybe cut out the hole as close as possible to the fire block, but where it will still be concealed by the TV. Keep us posted!

@Layarion 2 місяці тому

Hey i need to stud finder the works on rough, very bumpy wall that's lath and plaster? or a method.

@DanielPetrovaliev Рік тому

Where did you get these night shelves?

@Russianmafia10 Рік тому

When it comes to combining 3 or 4 wires, wago connectors are sooooo much nicer to use

@jnidositko Рік тому

The tool that you called "flush cut snips" is actually for pulling nails. This is why the head is rounded. You grip the nail with the tool and then pull to the side, using the face of the tool as a fulcrum. If you don't get it out in one pass, reposition it at the surface of the wood and repeat. They can be used from either the front or the back. In this case since these are finish nails, you can pull them through the back.

@FC-qe1wl 8 місяців тому

Actually they are called nail nippers.

@williamly-lee3973 Рік тому

Love the diagrams!

@LRN2DIY Рік тому

Thanks! They take longer to create but I learn better that way for sure. I appreciate you mentioning it!

@keemmadeit9412 Рік тому

Can you drop a link on tools that you have?

@user-jn2lk1lx6c 7 місяців тому

12 ga wire is for 20 amp circuit- 14 ga wire is for 15 amp service. Make sure breakers in panel box match wire rating.

@csl9495 3 місяці тому

Can you do a plaster and lath wall?

@angelmares6668 Рік тому

Nice,,easy explained

@stanleyvo5198 4 місяці тому

Nice explanation …❤😊

@GonzalesMansion 25 днів тому

Great job

@laddcampbell2833 Рік тому

So option 3 also applies if you have fire blocking studs I assume? I have attic access but there’s fire blocks in my wall that id have to drill through and I think id need about a 6+ foot drill bit.. not sure if they make that. Any advice?

@LRN2DIY Рік тому

You can use a long drill bit or a drill bit extender, or you can make what are called pumpkin cuts from the wall. They require some patching though.