946C SMD Hot Plate for Rework Pre-Heating or Reflow Soldering

День тому

The 946C Hot Plate provides a relatively uniform heating surface, allowing the temperature to be set between 50 and 350 deg C.
This unit can be used to pre-heat PCBs for rework or component removal, but I'm going to use it to reflow a PCB with surface mount components.
0:00 Intro
1:43 Grounding Check
2:20 Power On and Set Temperature
3:00 Thermocouple Measurement on Hot Plate surface and Reflow Profile Discussion
5:44 Thermocouple on PCB surface vs Hot Plate surface
8:14 Using solder paste stencil
9:45 Hand placing surface mount parts and reflowing solder
10:28 Visual inspection and PCB functional test
946C Solder Hot Plate 200mm x 200mm (affiliate link)
www.banggood.com/custlink/K3D...
Solder paste used - MG Chemicals Sn42Bi57Ag1 Low Temperature Solder Paste T3, LEAD FREE, NO CLEAN, 15g (affiliate links):
Amazon.com: amzn.to/3bwqFze
Amazon.ca: amzn.to/3utSj8y
Useful links:
Identifying SMT soldering defects and causes:
aimsolder.com/sites/default/f...
SMT reflow process guidelines:
www.aimalloys.com/sites/defau...
If you'd like to support the channel, you can:
Support me on Patreon: / gadgetreboot
Shop through my affiliate links!
Banggood www.banggood.com/custlink/3vK...
Aliexpress s.click.aliexpress.com/e/_AFeHwB
Amazon.com www.amazon.com/?&_encoding=UT...
Amazon.ca www.amazon.ca/?&_encoding=UTF...
Videos are mirrored at LBRY/Odysee: odysee.com/@GadgetReboot:4
#ElectronicsCreators

КОМЕНТАРІ: 26

@andymouse 3 роки тому

I use a hotplate for certain jobs and its great, nice to have the option...cheers.

@travishayes6678 3 роки тому

I've been eyeing something like this. Thanks for the helpful video!

@GadgetReboot 3 роки тому

It was definitely worth having, and I didn't even burn the bottom side of a PCB when letting it go up to 200 degrees for a long time to measure temperatures on the board surface, so it should definitely work for normal soldering time frames.

@StopClowningAround 2 роки тому

Very instructive. Thank you.

@TheEmbeddedHobbyist 3 роки тому

Great for keeping your tea / coffeee warm when your working hard as well.

@GadgetReboot 3 роки тому

and the 20x20cm one can also make an omelet

@TheEmbeddedHobbyist 3 роки тому

@@GadgetReboot well if it can turn it's hand to Crepes they got my money. :)

@MkmeOrg 3 роки тому

Handy tool!

@bskull3232 2 роки тому

If your hot plate can go to 260C, I highly recommend using SAC305, not the SnBiAg rubbish. Commercial flux are designed for SnPb and SAC305, and your commercial grade SnBiAg paste uses the same flux, which means by the time the solder melts, the flux were not heated enough to do its job properly. That's why not all parts are pulled to center automagically like you might have seen on videos. The denser your parts are, the more devastating this effect could be. So after struggling with having to repair each and every board reflow, I finally decided to move to SAC305, and I never looked back. Yes, it does cost more to buy gears for high temp reflow soldering, but it is worth it for me, even if I only do prototyping. Currently my setup has a Quick 854 for large area preheating, a Miniware MHP30 for small boards, a JBC NASE for precision fixups, and a Metcal HCT2-200 for first time reflows.

@64bittz93 2 роки тому

So basically you can use the SAC305 with this hot plate if I understood correctly. Is SAC305 just the name of the "recipe" or is it a brand name? Could you post a link to what you use? Thanks

@bskull3232 2 роки тому

@@64bittz93 SAC305 is a formulation, consists of Sn (rest), Ag (3%) and Cu (0.5%), a nearly eutectic alloy melting at 220C. This is commonly known as one of the two commonly used lead free solders. The other is SnCu without Ag, some formulations are eutectic, melting at around 10C higher.

@electronic7979 3 роки тому

Nice item

@josephcaporaso4774 2 роки тому

Hello, I also bought this device but there is something I don't understand or do wrong. For example, when I set the temperature to 175 °C, it remains at that temperature indefinitely. It does not go down automatically. I looked at the curve with a thermocouple and an arduino and the curve is purely upward. It absolutely does not follow the classic curve of the reflow. There is no controller? Do you have an idea?

@GadgetReboot 2 роки тому

yes there’s no controller, the device is just intended to power on and go to the set temperature so all I do is turn the power off and let it cool down when I feel it has finished re-flowing. It’s not the most professional way to do it but it works for the hobby things I’ve been doing. of course some sort of Arduino project could always be done to manipulate the temperature setting or cut the power but at that point if that much control is needed it’s probably better to do the classic toaster oven project.

@Zefbot 3 роки тому

Can you use that same type of solder paste manually if you don't have a stencil but stiil intend to reflow it?

@GadgetReboot 3 роки тому

Yes especially if the components don't have pins too close together like tiny ICs but even then the nature of solder mask and surface tension keeps solder where it's supposed to go once it melts and any bridges can be fixed with a solder wick/braid or maybe flux and an iron tip dragging excess away.

@SimpleElectronics 3 роки тому

But can it make paninis? Asking the real questions here! I like how thorough you went, I would have just put a bead of water on it and seen if it would evaporate at 100 degrees lol

@GadgetReboot 3 роки тому

It can make them, but you shouldn't eat them. And it would be better to have two of these to do top and bottom simultaneously (don't forget to use the affiliate links). With my luck a bead of water would have caused too much thermal shock and split the plate.

@DrexProjects 3 роки тому

Now I want a grilled cheese...

@kekekeernest8920 2 роки тому

What is the input voltage

@SpottedEagleOwls Рік тому

how do you clean your hot plate

@GEORGE-jf2vz 3 роки тому

Is it any good at making a grilled cheese sandwich? Gotta eat while de-soldering.

@GadgetReboot 3 роки тому

It's not bad but it has to be monitored closely or it burns. It has even heat distribution so it finishes fast. But only use lead free solder

@stevenspmd 3 роки тому

Stupidly the 100x100 isn't physically any smaller it just has a large border area around a smaller hot plate.

@tavinfortavinfor8927 2 роки тому

what about a computer fan to cool down faster? gecause it's no good idea touch a board with melted solder .it it'a a laptop board ,they can die

@kirklishman8997 Рік тому

When I used this product on 1.6mm fr4 with LEDs I had it at 280c did the job within 12seconds but I'm sure it killed half of my LEDs because they don't work now... But at 220c took ages I mean ages......