BEST Homemade Two Hand Multimeter - Finally!
Переглядів 26,173
День томуHigh quality PCB prototypes: www.pcbway.com
Project & PCB Here: bit.ly/49W2Cqb
🔥Arduino based multimeter capable of measuring current, voltage, resistance, capacitance, inductance, continuity, diode mode, frequency and a lot more. Still improving! Check the links for more.
🔀LINKS
-------------------------------------
Tutorial Page: electronoobs.com/eng_arduino_...
My tools: electronoobs.com/eng_afiliate...
False/True T-Shirt: teespring.com/it-s-funny-beca...
🤝SUPPORT
-------------------------------------
Join my Arduino Course (Spanish): bit.ly/2JY8icE
ELECTRONOOBS.io: electronoobs.io
Donate on PayPal: www.paypal.com/donate?hosted_...
Help my projects on Patreon : / electronoobs
my Q&A page: electronoobs.io/forum/index.php
Facebook page: / electronoobs
Canal en Español: / electronoobs en español
00:00 Intro
08:51 Thank You
Like share and subscribe to motivate me. Thank you
#multimeter
#homemade
#Arduino
@Marbslab 11 днів тому
Nice work. Perhaps you could design the housing so that the negative probe sticks out as far as the positive probe when the cable is wound up. This would make it possible to take measurements with just one hand. It would be even better if the distance between the positive and negative probes could be adjusted and fixed, for example when measurements are made on SMD components.
@benhetland576 2 місяці тому
Great! This one you should sell as a kit, since it has a couple of components that not everybody may have laying around just by chance :-)
@ELECTRONOOBS 2 місяці тому
You think people would be interested into buying it and then solder it themselves?
@BikramBehara7 2 місяці тому
Can you sell your pcb soldered
@benhetland576 2 місяці тому
@@ELECTRONOOBS I think so, but don't listen to me. I'm terrible at judgements involving other people 😉 Maybe you get some feedback in the comments here that give you a better sense of the demand out there.
@abdullahisanidodo2876 2 місяці тому
@@ELECTRONOOBS i think having two versions will do it, packaged and DIY
@abuhafss1 2 місяці тому
@@ELECTRONOOBS Yes, sure. The kit must include everything to make it finished tester, ready to use.
@autonoob 2 місяці тому
Cool. I would add female pinheaders hooked up internally to the probes. So you could easily connect it to a breadboard using regular jumper wires. And maybe a small magnet to hold compoments/screws temporarily.
@zaprodk 2 місяці тому
Great idea.
@artursmihelsons415 2 місяці тому
Nice! Best thing with DIY tools is that they can be tinkered to fit all needs.. 👍
@LokeshWankhede 2 місяці тому
Your projects are getting better and better day by day and these genuinely interest me. You're my favourite UKpostsr ❤
@Rich-on6fe 2 місяці тому
Interesting project. I would consider putting the display as close as possible to the probe tip. Round the case edges making it comfortable to hold. Ditch the neg probe holder. Consider socketing the neg probe.
@zaprodk 2 місяці тому
Agree. Display close to the tip, the rotating switch in the back.
@Gengh13 2 місяці тому
What's awesome about custom tools is that you can customize it for your application. You can have your own beeping sequence for different diode voltages, you can add a dfplayer for sound readout or whatever you want.
@benhetland576 2 місяці тому
Now I can just imagine what kind of sequences that would be... Maybe a binary encoding of the value on the display? Or it could be beeping the digits using morse code? Could also beep the digits like they are shown on an abacus, long beeps for a 5 bead followed by 0-4 short beeps for the 1's.
@barrymayson2492 2 місяці тому
I like it been looking for something like this as i often work on highly dense boards and with a desktop meter have take my view of the board to look it. This sometimes leads to me slipping of the probes. With this you can position the probe and read the meter looking at both. I have one suggestion make negative probe wire pluggable so it connected with different ones ie crokadile clip. But your products are becoming very professional thanks for your time and work.
@yitspaerl7255 2 місяці тому
Thanks a lot for sharing this. I have ordered the PCB's and the resin printed enclosure. I see another application for this: Automotive use. I don't like putting my expensive meter under the hood of my car in a place where anything can happen to it. Then I have to measure and watch the probes, trying not to make a short circuit. At the same time watching the multimeters display. With your design I don't have this problem anymore. Of course there are pen meters on the market, but your design is much more versatile. Maybe automatic screen rotation is nice. Not only for left handed people. Replacebe probes, maybe. There is sort of a standard in this. A buzzer for latching continuity checks. Definitely I do not mean this as ordering features ;) . Besides I do realize that you cannot fit everything on such a small board. However I do know that I am going to enjoy building your project!
@tmiller9099 2 місяці тому
Terrific! I wonder if the dial would last longer if the pogo pins were on the board and the pads where on the dial surface?
@meatmanek 2 місяці тому
That would also mean that the wear happens on the easily-replaced dial board instead of the main board with all your components on it.
@benhetland576 2 місяці тому
It also frees up some space on the main PCB, which can be used for some low profile components. The round PCB will rotate freely above without any pogopins coming down to strike them.
@CJ-Giddyup209 2 місяці тому
If there's one thing I could change about the multimeters I've had, it's being able to see the screen (usually testing 120v). Even with wrist straps it's awkward to look at the screen and hold the probes. With the screen attached to one of the probes, like yours, it could simply solve that issue. 👍
@Jackie-sg8es 2 місяці тому
I’ve been waiting for this. And you did an amazing job. It is a very well done and finished project. Great work.
@jorgedelcastillo2811 2 місяці тому
Buen trabajo, te ha quedado genial !!
@hippie-io7225 2 місяці тому
I love it when a good plan goes together! The switch idea is awesome. Circuit designers who are willing to go through several designs, like you, show passion and initiative. Good on ya y bien hecho!
@SD4LABS 2 місяці тому
Nice project! For the next iteration you could try using one of the newer ESP32 (ESP32-C3/ESP32-S3), you can directly upload sketch to it over the USB (no need for external USB to serial converter as it has built-in USB Serial/JTAG controller) and it also has built-in Wi-Fi and Bluetooth.
@pizvi 2 місяці тому
i cant thank you enough good sir!! its been years of my search for perfect mini multimeter and my journey is finaly over :D ordering PCBs right now..
@levieux1137 2 місяці тому
Nice work! I'd definitely add a buzzer to test for continuity (and one that reacts fast so that I can search the pin of an IC a track routes to). And I'd go above 1M ohms because with voltage regulators and low currents these days it's quite common to find values a bit above that limit. It's nice that the display updates quickly. A calibration mode/button would be great, to reset the zero and cancel wires resistance / inductance. Maybe you should sell it as a kit!
@ELECTRONOOBS 2 місяці тому
It already has a buzzer and LED for that
@levieux1137 2 місяці тому
@@ELECTRONOOBSah sorry, I hadn't noticed it!
@rodrigomartindelcampo9534 2 місяці тому
Great project! Also this is a great example of the cases when custom solution is better than off the shelf, cool dial
@NilsRohwer 2 місяці тому
Great work!
@grins047 2 місяці тому
Amazing! I really love your work. Thanks for sharing, you are a gem.
@teddyjamilonatefreire8797 2 місяці тому
I think this is a very useful project. Great job! and thanks for sharing all your knowledge with us
@user-qf6yt3id3w 2 місяці тому
I like the home made rotary switch.
@ranganatennakoon 2 місяці тому
its very cool step by step development ! nice work .
@helmutzollner5496 Місяць тому
Love it! Well done!
@louisbaldor4225 2 місяці тому
OMG!!! super useful project, I want to make one by my own, thanks again!!!
@padmanabhanrajesh2366 2 місяці тому
It looks very professional.Great work bro
@etce10avijitdey95 2 місяці тому
Incredible project. ❤
@ManosMaragkakis 2 місяці тому
That's a nice project man! Keep goin
@ftwproject658 2 місяці тому
Handy project! Really like the compactness. A cool add-on would be a high voltage resistive/capacitve voltage divider nozzle to attach to the front of the multimeter. You would need to add a toggle switch for 'HV Mode' which would simply be a multiplier to the output on the led, making it easy to read high voltages. The nozzle can be quite long to allow for reading high voltages in experiments. The nozzle would be 'keyed' to allow for snug fit with the multimeter tip. Cheers.
@dinkc64 2 місяці тому
Very cool project! The design is very nice and elegant.
@jparky1972 2 місяці тому
Looks great! I don't know if you have it already. But a buzzer option on continuity would be very useful.
@ELECTRONOOBS 2 місяці тому
It has a buzzer and an LED
@zaprodk 2 місяці тому
Add a function that reads resistance as a tone. Then you can look for shorts without looking at the display. A different resistance is very easy to "hear" @@ELECTRONOOBS
@mostrush4849 2 місяці тому
I would add indented text of modes to case and fill them with white ink. I would also add auto power off and add extra off step to selector like other multimeters (having to off position on start and end of selector is ideal) and remove side on-off switch. I also like to have ESR meter on capacitor mode.
@chiparooo 2 місяці тому
Very nice design! A very useful tool. Thanks for sharing!
@akashpathave8985 2 місяці тому
Great Video sir, Your My inspiration for Doing Graduation in Electroncs.. Thanks
@AbhishekKumar1902 2 місяці тому
loved it totally ❤
@leehewitt9559 2 місяці тому
Great project 👌
@benhetland576 2 місяці тому
For those that wanted a "thumb wheel" access from the side of the meter, I suggest only a slight modification. On the main PCB offset the position for the mode selector wheel to one side a little bit. Maybe "down" when viewed with the PCB text upright (the display to the right) is best to reach the thumb. The opposite side can now be a straight edge for both the PCB and the case. Make an opening in the case where the wheel protrudes. On the top wheel cap, let it go around the outside of the PCB wheel, but also make the outside a cerrated edge. It will serve as the thumb grip in the new side opening.
@mikeseba7817 2 місяці тому
Another great project! 👌👍👍👍
@Isaac_Diggs Місяць тому
Awesome work
@vishalkumar040393 2 місяці тому
I thought the Dev Board was the best, but this next level. I will make this one. Nice work. Thanks! for sharing.
@luisb.458 2 місяці тому
Gran trabajo.... impresionante.
@LeonZhou-gi5rq Місяць тому
Great! I plan to make one.
@HadjerBOUYAHIAOUI 2 місяці тому
nice job , keep going!
@hakim_mi 2 місяці тому
This version is really good, I’d try to order this
@jimbarchuk 2 місяці тому
Outstanding project! Through-wall mains wiring detector.
@benhetland576 2 місяці тому
Perhaps that's just a firmware update away since it already has a hall sensor.
@SweetLemon13 2 місяці тому
Very good, bro, a hug from Brazil.
@TheDarkGunner100 2 місяці тому
Using the bluetooth functionality one could stream voltage measurements to the phone and make a crude oscilloscope. Pretty nice to see the rough shape of the voltage or dropouts etc in a pinch!
@stevesousa6810 2 місяці тому
There is only one problem. It is only possible to give one like, I wish I could give you more. Well done
@Poult100 2 місяці тому
Excellent! 👍👌
@winlose3073 2 місяці тому
very nice idea! I can't think of any other ways of making it better except if you could make it more slim that would be cool. Keep going.👌
@alessandrovichi761 2 місяці тому
Very good and cool project
@jozefnovak7750 2 місяці тому
Super! Fantastic!
@harikamalakarreddydarapu7410 2 місяці тому
Excellent
@rodrigofigueiras3027 2 місяці тому
Realmente esta muy bueno, desde la solución con el dial hasta la carcasa que retiene el cable y la punta. Le faltaría poder ver señales de baja frecuencia tipo osciloscopio y estaría muy bueno también recibir las mediciones en la pantalla de la pc o celu con bluetooth. Esto veo que lo usan mucho los UKpostsrs que hacen contenido como vos y muestran las mediciones directo en pantalla si necesidad de cámaras que muestren los valores. Vas por buen camino... Exitos
@rodrigofigueiras3027 2 місяці тому
Un detalle más, en la carcasa hace marcas de cada paso que da el dial y si podes algún símbolo que indique que estas midiendo en relieve. Son detalles que lo harán ver más profesional y completo.
@jazekerxx7535 2 місяці тому
@Electronoobs it's becoming better and better, very nice! what would i add? maybe you could add text with youre fiber laser? also it would be nice to see how the accuracy compares to youre Keysight multimeter..
@ELECTRONOOBS 2 місяці тому
Accuracy is pretty decent especially for voltage and resistance using the 16 bits ADC
@benhetland576 2 місяці тому
@@ELECTRONOOBS Actually having some form of calibration ability, like the older multimeters had internal trimpots, would be a nice future feature enhancement. It doesn't need to be accessible from outside the enclosure.
@benhetland576 2 місяці тому
Another way to calibrate could be via the USB serial. Procedure and correct values could be prompted to and read from the user that way. Calibration parameters could then be stored in the internal EEPROM.
@metalazzo 2 місяці тому
Nice work 🙂
@abuhafss1 2 місяці тому
Very nice project. BTW, you should have added option for testing zener diodes.
@jimsubtle886 2 місяці тому
What are your thoughts on the longevity of those pogo pins contacting your PCB many times? Do you think just asking for a large copper weight on the pads and then using a long lasting lubricant to outlast the lifetime of the tool? Gold plated pogo pins are great, but once that plating wears off, there might lesser consistent metal inside that is either very hard or very soft. I have had quite a few cheap multi-meter PCB traces worn out this way. Please keep going, awesome project! I love the progress so far!
@user-zr5rh9zv9h 2 місяці тому
wow... that is amazing you insfired me thx
@malkurju 2 місяці тому
can the display be inverted to be used on the left hand aswell? really nice job well done!!
@unhappyalienbrocker 2 місяці тому
Great work! Try (?) to add a switch to reverse the probes (for diode measurement)
@widyahong 2 місяці тому
Add esr in capacitance measurements and oscilloscope on voltage reading 🔥
@bigboykris2630 2 місяці тому
That's awesome
@RdGear 2 місяці тому
Nice video .
@iuhere 2 місяці тому
wow really nice one
@Wasgehtnab 2 місяці тому
its like the POKIT Pro, nice
@kreynolds1123 2 місяці тому
I love it. Just one concern about the leads and the degree that they bend when it is wrapped up. High degree bends can weaken and break the wires in leads.
@dougaltolan3017 2 місяці тому
Even though you don't use this for high voltages, I'd recommend a switch that connects the battery to either the charger or the circuit, but not both. Sure, you can't charge it while using it, or run it from a charger, but you'll prevent the almost inevitable unintentional short circuit via charger and power supply for the circuit you are testing.
@yetanotherdan 2 місяці тому
I like this project a lot! I wonder if a sonic screwdriver (or pen light) style of multimeter can be made with the selector knob being at the base. I hope you get to a point you can sell kits of this.
@TechwithStefan 2 місяці тому
Hello, this is a very nice project, and I can give you a free advice, since it should be a 2 hand multimetter, it would be great to make the Dial for changeing modes into a wheel , that you can change with your thumb, so that you can change faster what you need to measure. Similar to a Jog dial that previous phones had like the old Sony or old Blackberrys. Let me know if this makes sense, PS: foarte misto proiectul :)
@sudheerkumar5966 2 місяці тому
Great vedio sir
@JonathanDeWitt1988 2 місяці тому
Another interesting project Andrei. I wonder if there would be any improvement with a version that uses the barebones ESP32 chip. With its built-in Bluetooth it would probably at least eliminate the need for the external bluetooth module. Granted that is probably more trouble than it is worth given how much work you've already put into this version.
@innocent1. 2 місяці тому
Wonderful 💝
@clive4500 2 місяці тому
looks really good I would have the rotary switch with course pattern on the edge of the wheel so that it could be changed with your thumb I would get rid of the top part of the knob on top the top of the rotary knob could be within the case with cutouts to show the functions the fuse needs to be replaceable even if it has to be a bit bigger. and for sure the battery needs to increase in size that one looks really small.. Just some suggestions to what looks a really good and useful meter
@yitspaerl7255 Місяць тому
The PCB's and the resin printed parts have arrived and are beautiful. So I only have to order the parts Is it my fault that I miss the STL file for the dial cover?
@MichalKottman 2 місяці тому
This is very nice! I always wanted to see the voltage right next to the point I'm touching, especially if the contact point is very small. Having to look away to a "real" multimeter for a readout is very distracting.
@stm32user 2 місяці тому
Super.
@Circuit42 2 місяці тому
Great Project Evaluation. But U can use a Magnetic Encoder for the Mode selector
@rok9526 2 місяці тому
Great project! I think buttons for switching modes (dedicated button per mode?) would be mechanically more robust long-term.
@Derfboy 2 місяці тому
I'd add some strain relief for the probes so they don't rip out when my brain forgets that the cable is shorter...lol
@labiadhchokri2124 2 місяці тому
nice project , does this meter show the polarity of a voltage , you can add oscilloscope mode and logging mode and the min and max voltage , for the scope u can use your phone screen via Bluetooth .
@GoatZilla 2 місяці тому
uh, kind of seems like the pogo pins should go on the static base instead of the dial. that way when they wear a track in the PCB... you can just replace the dial instead of wearing a track into the base.
@inoid724 2 місяці тому
Geat work, is there an ESR Meter included? This would be awesome.
@musaadejoshuaibuopaluwa1712 2 місяці тому
awesome
@zewarmdur9195 2 місяці тому
Well that is great thing to have tbh my multimeter wires are really annoying too they always get tangled so i hope you finish this one . Because i might buy one tbh ... what would i add if could be well the case u made is kinda big like if u use it like pen i mean at least the width of it not thickness + that would be really good if the negative wire was recla retractable after u let go of the negative wite or maybe something like old phone they were like spring will get smaller and + if u could have like plastic tip to put at the tip of the positive tip like pen tip case after all its really great project I love it how compacted its well done brother 🙌🏿👏
@saduniwathsala 2 місяці тому
Nice and excellent 👍👍👍. Go upgrade and make it slimmer 👍👍
@mrruvs5132 2 місяці тому
All your projects are great. And I have a question, why are you still using the Micro USB connector and not changing to type C, regards
@ELECTRONOOBS 2 місяці тому
Is kind of big and don't need it for this project. For other projects with more power I did use type C...
@youtubasoarus 2 місяці тому
You could make it so the wheel is actuated by your thumb (thumb wheel?) so you can change modes with one hand.
@tenlittleindians 2 місяці тому
I just got a tiny pen multimeter from AliExpress for $8.00 dollars and it's got more features than my old full sized multimeter!
@ljbengineering1163 2 місяці тому
Nice device! I looked at your schematic. Can you elaborate more on how the arduino is measuring capacitance? Thanks!
@ELECTRONOOBS 2 місяці тому
Everything is explained here: electronoobs.com/eng_arduino_tut84_2.php
@Kmnri 2 місяці тому
Amazing project, what i would do... use esp32 since you already have bluetooth module, so why not just use wroom32 which is a lot faster, has built in BLE, way more processing power and could probably make entire thing smaller.
@TheRcEngineer 2 місяці тому
Hi Thank you for sharing. The stl file of the dial cap is missing only the lower part is in the stl files.
@capkenway 2 місяці тому
typec instead of microb would be nice, also it can also act as a oscilloscope if it does serial over usb and a have a program to make sense of it. a very interesting project though
@fouzaialaa7962 2 місяці тому
this is actually useful you should integrate it in to a breadboard to have a smart breadboard , that way you can sell it on your shop i've seen alot of multimeters , but i rarely see any breadboard that have an integrated multimeter , and your circuit is small enough to do it
@nadiaplaysgames2550 2 місяці тому
look up the jumpperless breadboard
@fouzaialaa7962 2 місяці тому
@@nadiaplaysgames2550 thats not what i mean !!!!!
@nadiaplaysgames2550 2 місяці тому
@@fouzaialaa7962 jumperless allow you connect the pico mega to data log or read analog values and report back passively
@diegogarciamedina6363 2 місяці тому
great project, please add inductance measurement
@ELECTRONOOBS 2 місяці тому
It has. Check the previous tutorials to learn more on how to measure it!
@94HellGate 2 місяці тому
you should switch the dial housing to be on the outside instead of the top so you can do 1 handed mode changes
@JimmyCall 2 місяці тому
Could the power switch be too fragile?
@xboxgamer9216 2 місяці тому
How is the accuracy of ads1115? do we need to adjust for any kind of offest or errors at specific conditions
@ELECTRONOOBS 2 місяці тому
Ie easy to calibrate just by touching the probes when you calibrate it it will find the offset
@gamiwv 2 місяці тому
Do you plan any group buy ? Looks very interesting to me (maybe a little more flexible than MS8910)
@ELECTRONOOBS 2 місяці тому
what is a group buy?
@gamiwv 2 місяці тому
@@ELECTRONOOBS terminology we are use in diyaudio for successful projects when some of us want to reproduce a project, each for himself. In a previews comment I read about a "kit". Some of the components aren't very easy accessible to all of us (the pins of the switch for instance) or the ICs. So the project leader after summarize the requests is buying the total amount (plus some more) and sent the envelops to the "members of the project" by mail
@YouGenom 2 місяці тому
Labels on the modes would be an important improvement as wouldn't remember after 3 weeks what position is what mode 😅
Electronoobs
Переглядів 52 тис.
Костильов Онлайн
Переглядів 220 тис.
ЮМОР ICTV - Официальный канал
Переглядів 377 тис.
BBC News Україна
Переглядів 655 тис.
SANU4YOU
Переглядів 2,7 млн
ЗОЛОТОЕ-TV
Переглядів 1 млн