Very thorough, thanks for that!

Thanks for the upload

Great video. Thanks ! Don't forget New sprocket bolts from BMW. They stretch...

Nice work man thanks!!!

Thank You Master!!! loved your video so much!!!!!!!!!!!!!!!!!!

exceptional work. thanks.

Nice instruction

Thanks for the video. I have a S63 in the middle of valve stem seal replacement. Engine in car, valve covers off, started to set time for cam removal with AGA tools. Rotating clockwise a bit reached a hard stop, short of reaching MP. Engine would rotate back a little, then stop when going forward at same place. Saw in TIS that it is OK to back rotate as long as chains were tensioned. Still had tensioners in place, so spun the engine nearly a full revolution backwards and achieved MP mark for crankshaft and all four cams are dead on with timing check plate. Interestingly, with timing tools removed, the engine will only turn a little forward and little backwards. Feels like a hard stop in both direction now. Ever seen something like this?

Does cam phaser need to be replaced if timing went retarted or just remove bolt plus lock tite or replace

Hi, could you advice on a similar knocki'g noise on N63 550i Xdrive. Could a send you a video?

Great video thanks Can you show us how to set chain

In the future please do the same process on the N63TU.

Very good

Can you please tell me when your removing cam shafts When cylinder 1 is at 150BTDC dies that mean cam shafts are in resting position?

dude you are amazing. where r u at brother ?

Thx👍

😊😅thank you thank you awesome video detailed 😊

The exhaust cam on the left points to the right side of the car is you’re doing it with the engine on the car

You did not use the tensioning tool. 10:38. You had to press the alignment tool to tell yourself timing is set. It is not. Your timing is off.

Can someone leade to the torque specs and pattern for the Cam caps

hi Stanislav! very good video! really detailed and instructive. im about to do the same with my N63 5.0i. if you have more videos on the n63 it would help! 👍👍

My Lexus Ls 400 Still Running strong with 328 Mi .

*l have a 2008 BMW X6 and the engine is missing timing What was happening What happened is I was driving it then it just simply stopped and now the car won't start I took it in the BMW and they're telling me I need to replace the entire engine Even though I just replaced the engine under warranty about 50,000 mi ago Is this a problem that can be fixed??*

Thanks

Do you have any videos on replacing the oil pump chain on tu?.. I have a n63tu engine with a broken chain and trying to figure out what would be the best easiest way to fix

Aren’t you suppose to apply tension to the chain before you tighten the cam bolts? Because the tensioner will still have slight slack in it

The problem with this engine the cylinder wall get scratched then sound comes when it’s hot. I have now 3 engine with low mileage 20.000km only cylinder 8 scratched . Maybe I repair them or sell them

Any one happen to know the torque spec on s63 crank bolt. Just reassembling after timing chain replacement

Thansk for the Info, I got S63 Engine would be the same tool and same way to do ?

Great Thx.....

Спасибо)

This timing guide apply to the N63 twin turbo? Also having intake Vanos and crankshaft code. Any ideas where can I start checking to get rid of those code. Vanos solenoid were remove and clean

Very good video nid clarity why you say the exhaust cam on the inside v8 exhaust it has to be outside.

Pls can you share me where you got the timing tool from?? I really need it..

SO 150 DEGREES BEFORE TOP DEAD CENTEr THE CRANKSHAFT ENSURES ALL 8 CYLINDERS ARE FAR FROM Tdc, no valve interference?

Pourquoi les cylindres de la culasse gauche ne répond plus

I bought a crankshaft with new bearings but cannot get it to start constant timing codes for all 4 cams. Timing is set and have re checked several times. Is it possible i have the wrong crankshaft? Any suggestions? Thank you

Where are you in Sac? How can i get hold of you?

Bro, the correct timing is already done on the new engine you got or you had to do this on the new engine? I don't think my mechanic did this to my new engine 😖🤦‍♂️

Where can I find that tool?

Any link to this tool? AGA is absurdly out of price...it's like they lost their minds.

I'm looking for a BMW Mechanic to work on my BMW X50i