Cast Iron vs Aluminum Engine Blocks: Which is Better?

  Переглядів 142,415

The Engineers Post

The Engineers Post

День тому

The engine block is a crucial component of an internal combustion engine. It serves as the foundation for various engine parts and provides structural support for the engine's operation.
Early engine blocks consisted of just cylinder blocks, to which separate crankcase was attached. Modern engine blocks typically have the crankcase integrated with the cylinder block as a single component.
Parts of Engine Block:
The main part of the engine block is a cylinder. It is the space in which a piston travels. Other parts are Coolant Passages, Oil Galleries, Crankcase, Bearings, Cylinder head, Cylinder liners, Deck Surface, and Camshaft housing.
How many types of engine blocks are there?
Three types of engine blocks are most common within modern cars: inline, V, and flat.
Inline engine blocks are most commonly found in smaller cars thanks to their simplicity. In this cylinder are arranged in a single line along the crankcase.
V engines have cylinders arranged in two banks at an angle to each other, forming a V shape when viewed from the front. Common angles for V engines are 60, 90, or 120 degrees.
Flat engine block
The third and final type of engine block is the flat engine block. In a flat engine, the cylinders are arranged horizontally and lie on opposite sides of the crankshaft, resembling a boxer's fists punching outward. This allows them to have a greater weight distribution and lower center of gravity.
--- Time Stamp --
00:00 - Introduction
00:40 - Parts of Engine Block
01:13 - Cast Iron Engine Block
02:14 - Aluminum Engine Block
03:07 - History
05:01 - Cast Iron vs Aluminum Comparision
08:43 - Which one is the Best?
09:24 - Types of Engine Blocks
12:16 - Common Engine Block Issues
13:38 - Outro
#engineblock #engine
Check out more videos:
Every Engine Layout - • Learn about every Engi...
Car Engine Parts - • Car Engine Parts & The...
Disclaimer: This video is for educational purposes only. We are not in the auto repair business nor publish automotive service manuals. This video is not reviewed or authorized by any vehicle manufacturer. This video is intended only as general guidance. Every system is slightly different, so refer to the owner’s manual of your vehicle for any specific information about your model. Remember that only proper service and repair procedures will ensure your car's safe and reliable operation.
Copyright Disclaimer: Copyright Disclaimer Under section 107 of the Copyright Act 1976, allowance is made for “fair use” for purposes such as criticism, comment, news reporting, teaching, scholarship, education, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational, or personal use tips the balance in favor of fair use.
Follow us on Facebook:- / fanpageengineerspost
Contact us: hello.theengineerspost@gmail.com
Visit our Website for more articles:- www.theengineerspost.com/

КОМЕНТАРІ: 169
@4G12
@4G12 2 місяці тому
IIRC, the best material for engine blocks, especially for high performance production cars that are expected to be reliable, is CGI (Compacted Graphite Iron), an iron alloy used for NASCAR engines which are known for engines with even higher mean piston speeds than F-1 engines and cover longer race distances. It's not cheap though.
@MrD3000
@MrD3000 2 місяці тому
Those engines are usually also used only once, since they're worn out after a single race.
@newfie-dean5803
@newfie-dean5803 25 днів тому
Aluminum blocks typically handle engine overheating conditions better than iron blocks. This is because aluminum has better thermal conductivity, meaning it can transfer heat away from the engine more efficiently than iron. Additionally, aluminum tends to have a lower coefficient of expansion, which reduces the risk of warping or cracking under extreme temperatures compared to iron. As a result, aluminum blocks are often preferred in high-performance engines or applications where heat management is crucial.
@foch3
@foch3 20 днів тому
They manage heat not overheating. Everyone knows aluminum heads warp easily when overheated. The most powerful engines per cubic inch, Top Fuel dragster are cast iron.
@user-bk2ig8bf6o
@user-bk2ig8bf6o 19 днів тому
Ive thought my aluminum block was inferior to iron for a long time because of strength, but I’d much rather have better cooling.
@Bob-cd5pp
@Bob-cd5pp 27 днів тому
Wrench turner for 60 years . Steel is stronger & last longer Aluminum is lighter that't the only advantage. I had a 64 3.8 XKE the Best car every made bought in 1971 for $1000 those were the days my friend...
@user-yi2vy8mn9e
@user-yi2vy8mn9e 17 днів тому
I'm with you all the way been turning wenches now for 25 years and wouldn't give it up for the world. Cast iron are the best
@EWA8755
@EWA8755 Місяць тому
Not crazy about the ai text to speach. But very concise and informative.
@hambone2335
@hambone2335 Місяць тому
I have studied this for years. I have found out that a cast iron block is made from iron, and a cast aluminum block is made from aluminum.
@danabuch324
@danabuch324 Місяць тому
Thank you. I was going to post the same thing.
@tedjones-ho2zk
@tedjones-ho2zk Місяць тому
Funny but true
@Cybersawz
@Cybersawz Місяць тому
Those are profound findings. Your studies have finally paid off!
@chris.eskimo
@chris.eskimo 22 дні тому
Wow ! Really!? Holy crap !!
@oldbatwit5102
@oldbatwit5102 Місяць тому
Cast iron for me, every time. I also prefer side valve engines, drum brakes and wooden wheels with iron tyres.
@andretorben9995
@andretorben9995 Місяць тому
There is no simple answer. Its like asking what tire is best. It all depends on situation and purpose. Probably the most important factor is choice. Its great to have the option of selecting what material block you want to use for your application.
@michaelbenardo5695
@michaelbenardo5695 Місяць тому
It depends on what you are using it for. For conventional passenger cars and trucks, cast iron is the best, as it is more durable and more resistant to damage. For racing, aluminum is better because it is so light. It can mean the difference between winning for a few inches or coming in second by a few inches. In racing, that is all the difference in the world.
@oldbatwit5102
@oldbatwit5102 Місяць тому
'For conventional passenger cars and trucks, cast iron is the best,' ... Nope.
@Support_Ad_Blocker
@Support_Ad_Blocker Місяць тому
@@oldbatwit5102 yep
@richardschipper5989
@richardschipper5989 29 днів тому
@@Support_Ad_Blocker then why are the vast majority of car engines aluminum?
@lesklower7281
@lesklower7281 Місяць тому
The introduction of nickle to an iron engine block increases it strength by at least 160% done in the R series engines from Toyota making the engine more reliable and durable and l have a 1997 Toyota Hilux with a 22R engine and it is still running really well and with its total lack of tech makes it very reliable vehicle considered one of the most reliable engines ever made simplicity over engineering equals ultimate reliability
@user-yi2vy8mn9e
@user-yi2vy8mn9e 17 днів тому
Your damn 😂 right I had the same truck it won't die😂😂 body goes first
@alfredkevin2792
@alfredkevin2792 2 місяці тому
This is Good and recommended
@scottroland6577
@scottroland6577 Місяць тому
Excellent and informative. Thanks!
@Sourpusscandy
@Sourpusscandy 2 місяці тому
Thank you, very well done!
@eugeneoreilly9356
@eugeneoreilly9356 2 місяці тому
Iron block and head for me anyday.
@wendwllhickey6426
@wendwllhickey6426 Місяць тому
Iron blocks don't blow head gasket as easily as aluminum overheat very easily and blows head gaskets
@nighthawk0077
@nighthawk0077 Місяць тому
​@@wendwllhickey6426not really aluminum can last 20+ yrs as long as you maintain and don't abuse it
@robertmceuen3630
@robertmceuen3630 Місяць тому
​@@wendwllhickey6426I believe my 2014 Honda 2.4 4 cyl is aluminum block and head. 88000 miles so far with 0 problems. Other Honda and Toyota go millions of miles with similar engines.
@martinwarner1178
@martinwarner1178 Місяць тому
yep, every time. they will get you and back better than alli.
@STohme
@STohme Місяць тому
Very interesting video and excellent technical information quality content. Many thanks.
@craigpennington1251
@craigpennington1251 Місяць тому
Iron or aluminum/depends on what you use it for. I'm partial to all cast iron engines with carbs.
@VGHCX
@VGHCX 17 днів тому
Which is better? Depends on the purpose of the engines intended use.
@comradeyuri8492
@comradeyuri8492 Місяць тому
Cast iron blocks are a must for boosted engines and using nitrous. Alum. blocks are 100 lb. lighter and work well with cast iron bore sleeves. FORD sella high nickel cast iron engine blocks for super high stressed usage, but the price is frighting. But both GM and FORD use alum. blocks in all their V8's. Chrysler uses cast iron blocks in all their Hemi engines even the 5.7 and the 100 lb. weight is in the front of the vehicles, right where you don't want it ! Of course, cast iron blocks are cheaper to manufacture, so there is that !
@brandedmcgowan9414
@brandedmcgowan9414 Місяць тому
For the GM HD pickup trucks they produce iron block 6.6l l8t gasser, and yeap I have a 2012 RAM 1500 with the iron block eagle HEMI but they use aluminum cylinder heads.
@colestaples2010
@colestaples2010 19 днів тому
Aluminum as long as it’s taken care of. It’s soft material so I’m sure if neglected it falls apart sooner
@henrycarlson7514
@henrycarlson7514 Місяць тому
So wise , Thank You .I agree they both have there place .
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
Their place, not "there" place.
@ESPLTD322
@ESPLTD322 Місяць тому
Iron by far. The extra durability is worth the extra 200 lbs or whatever of weight and the extra 5 mins it takes to reach operating temperature in cold weather.
@zahimiibrahim3602
@zahimiibrahim3602 Місяць тому
The actual weight difference is much less, on average 15-17kg or less than 40 lbs because aluminum blocks needs to be thicker and more reinforced. The driving 4 answers channel discusses iron vs aluminum engine block pros & cons in more detail.
@jkim6200
@jkim6200 2 місяці тому
Not too many manufacturers offer blocks of similar design in both aluminum and cast iron, thus restricting the options for a given application. LS engine being one of the limited few.
@shadowopsairman1583
@shadowopsairman1583 Місяць тому
I think there is only 1 LT1 Engine that is Cast Iron now and that is the L8T
@jkim6200
@jkim6200 Місяць тому
@@shadowopsairman1583 Another GM engine series. The LT series is the successor to the LS.
@brandedmcgowan9414
@brandedmcgowan9414 Місяць тому
The inline has a low end torque advantage and better balance operating performance as well as being fuel efficient, can handle boost manly turbos and durable (mostly I6s) The v engines can fit in a variety of applications and are more sporty performance oriented engines, much like the inline engine the v engine can handle boost (supercharged and turbocharged) and can produce torque at a wide range powerband but way more over higher rpms than an online that completely tails off so flat. Depends on what you using your vehicle for.
@mobythemerpup1515
@mobythemerpup1515 2 місяці тому
A Steel engine block would be at the very least 2 Times Stronger At 40K-PSI But It Could be at 3 Times Stronger At 60K-PSI Maybe Way More
@cindys1819
@cindys1819 Місяць тому
Well, let's say you have a 1976 to 2000 Jaguar and you dont want to put up with all the at times unending Jag engine and transmission problems. So you do something sane and drop in a GM Small block. But you wsnt to stay in the 400 to 500 Hp (or so) range of poeer. Then an Aluminum block makes sense. Set the engine back as much as possible and with the 100 lb or do weight savings, enjoy the often noticeable better handling. Give you now optimise the benefits with upgraded tires and front end components tuned to the new better weight distribution. So there are times that a switch to An aluminum crate engine makes real sense. the tires and front end components that are
@user-qr7ee2cp4y
@user-qr7ee2cp4y Місяць тому
Depends on what you want and how much you have to spend....
@MrRoaster69
@MrRoaster69 2 місяці тому
Wow nice explanation on Cylinder Block
@MercInDepth
@MercInDepth Місяць тому
Clear and concise. Loving the insights. Keep the great content coming! 🔧
@mossab8209
@mossab8209 2 місяці тому
How do I know if I have an aluminum or iron block?
@ronjon7942
@ronjon7942 2 місяці тому
Magnet?
@smyrtuss6797
@smyrtuss6797 2 місяці тому
Decode your VIN number. In raport should be written everything about every part of car
@ronaldderooij1774
@ronaldderooij1774 2 місяці тому
Easy to see. Aluminium blocks corrode over time. The "color" will be lighter grey with white spickles (no panic, it won't hurt the block). Iron blocks do not change "color". Too bad if your block was painted.....
@BruceDragon-sf1tr
@BruceDragon-sf1tr Місяць тому
If your engine is cold, and you start it up... if the temperature raises pretty quick, its probably aluminum...if it takes awhile for that temperature hand to rise, its probably iron
@philipethier9136
@philipethier9136 Місяць тому
@@ronjon7942 Bingo.
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
Aluminum blocks are great if you don't mind having to replace the engine every 70K miles or so!
@eastcoastmostwanted710
@eastcoastmostwanted710 2 місяці тому
Titanium block has left the chat
@ronjon7942
@ronjon7942 2 місяці тому
Brilliant.
@fireflyraven2760
@fireflyraven2760 2 місяці тому
That maybe for the best
@Pacem_
@Pacem_ 2 місяці тому
Maybe so expensive 😢
@user-cd8jh8jk4n
@user-cd8jh8jk4n 2 місяці тому
but expensive
@bruettingmarcus
@bruettingmarcus 2 місяці тому
Titanium would be terrible - if scratched or scarred it will break. You also have to use only titanium on titanium - so titanium heads, valve covers, oil pan, screws it is and so on …
@Karim-ifInwUstfu702
@Karim-ifInwUstfu702 25 днів тому
titanuim engine exist ?
@nickb5391
@nickb5391 27 днів тому
Iron blocks are heavier & take longer to warm up, the alloy block & or head need skimming as the distort more
@davidherrera2465
@davidherrera2465 11 днів тому
Exelente Dato 👍 Al Igual Que Los Nuevos Motores de Aleación de Aluminio Son Mas Resistentes 👉👍
@timr31908
@timr31908 20 днів тому
Give me one of those Vega aluminum motors... It's a matter of fact give me about six of them.. so I can get through a season
@rdsledge
@rdsledge Місяць тому
Al with Fe cylinder liners! All thought Al blocks with the proper Harding of the cylinders are probably just as good as Fe.
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
They're not. They can't last nearly as long.
@adigerlaprasad5348
@adigerlaprasad5348 2 місяці тому
👌👌👌💐🇮🇳
@RocksDtv
@RocksDtv Місяць тому
30YEARS DIE CAST IRON BLOCK ISUZU 4JA1 ENGINE STILL RUNNING CONDITION
@williamhelms9942
@williamhelms9942 Місяць тому
Aluminum engine blocks are of lighter weight than iron in a car for auto racing and by design for sub compact road cars. Neither have any performance advantage(s) over another.
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
But there's a huge difference in durability.
@SamuelGoolsby
@SamuelGoolsby 18 днів тому
Heads up. My 6.7 V 10 spark plug shot out of the threads. Aluminum.
@steven-nb6rt
@steven-nb6rt Місяць тому
I prefer cast iron blocks myself for good heat dispersing. One thing I will never have again is cast iron block with aluminum heads. Big gasket issues costing a lot of money.
@falcorthewonderdog2758
@falcorthewonderdog2758 Місяць тому
Aluminum transfers heat better than cast iron.
@rogerdodrill4733
@rogerdodrill4733 Місяць тому
LT1 is reliable with this type
@1gbayfisher
@1gbayfisher 20 днів тому
Not really an issue. So many modified cars run this combination. I haven't had an issue in 20 years of doing this.
@dhanisvaran5135
@dhanisvaran5135 21 день тому
I've own 2 stroke 90s bike, 4 stroke and modern bike with aluminum u all know 2 stroke engine need constant rebuild & it's a dry engine only runs 2 stroke oils not like 4 stroke wet engine always had 4t oil flooded. for me iron block is my choice, many things can do with iron in my experience I've used both aluminum & iron iron cost less than aluminum came to repair ( seriously) my motorcycle 90s engine got crack but can be repaired also rebored, heat treatment & Alot but when my another motorcycle engine got aluminum that only can replaced cannot be repaired it's cost Alot that price are high I've find aftermarket iron part's install it + tuned it's runs 5 year without breaking even overheating, raining water, harsh riding it hold up , I'll sell it after 5 year . if u know people work with iron block cheap price - You are safe aluminum block, engine is garbage it's not strong inaf to withstand environments like raining hit sudden hot engine it will crack and riding in summer hot aluminum can't hold up over heat condition and other more seriously telling my experience don't left without like my comments seriously
@mtopuk
@mtopuk Місяць тому
Offcourse cast iron if durability, long life and cost frindly one needed. İf performance needed with light weight so aluminum
@richardschipper5989
@richardschipper5989 29 днів тому
an iron block will go 70-100K miles before needing a rebuild, new modern aluminum engines run for hundreds of thousands of mile before needing a rebuild.
@flowtime8673
@flowtime8673 16 днів тому
Tungsten block has left the chat
@tr7b410
@tr7b410 Місяць тому
The Volvo 240 series had a cast iron engine block.Life expectancy=between 300 & 500k miles.Do the math,buying a new car=aluminum block every 150-200k miles.
@user-ez3il1yy6i
@user-ez3il1yy6i Місяць тому
I Like Mine Bullet Proof !!! 😎
@synthyawylder3297
@synthyawylder3297 Місяць тому
Whether the block be iron or aluminum, I would never, ever, want an engine with the head(s) being a different material than the block - iron block & aluminum head, or aluminum block & iron head - since the 2 metals expand & contract at different rates & amounts, blown head gaskets are a perpetual problem. Another is less well known: that of corrosion, the result of 2 different metals being bolted to each other, & especially with heat & a working fluid passing between & through them. Aluminum engine blocks are also less tolerant of over-torquing, & special attention must be observed, when considering the different torquing specifications during servicing or rebuilding the 2 different types of engines. Iron engines will tend to tolerate being overheated, better than aluminum engines; more often than not, if an aluminum engine suffers a catastrophic cooling system failure, it's best to simply replace it, as everything will likely be warped & lose its temper. Most of my experience working on engines, has been in the marine field, & those engines lead a hard life, usually being operated at full throttle & load - both iron & aluminum engines will fail, but for heavy duty & long life, especially for diesels, iron is best; for outboard engines, aluminum is best due to its inherent lighter weight. I've never seen engines with the 2 different metals making up the block & head(s) have as long & relatively trouble-free life, as those made of 1 or the other single metals. Aluminum also has an additional weakness, that of its reaction to the hot water-glycol mix, if there's ever a blown head gasket, & the coolant finding its way into the cylinder(s), &/ into the crankcase - aluminum is more reactive than iron. Ofc, the bearing materials of either type of engine, simply don't tolerate that water-glycol mix at all! Air-cooled engines do have their advantages & their place in certain applications.
@richardschipper5989
@richardschipper5989 29 днів тому
you really know nothing about engines
@1gbayfisher
@1gbayfisher 20 днів тому
Iron block for boost, aluminum for n/a...
@dr.hugog.hackenbush9443
@dr.hugog.hackenbush9443 2 місяці тому
Whats the difference? About 100lbs and $1000.
@TexasNationalist1836
@TexasNationalist1836 21 день тому
Aluminum is more expensive and lighter?
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
And a much shorter lifespan.
@pvdp2
@pvdp2 22 дні тому
Cast iron is the best!
@RHF52
@RHF52 Місяць тому
During the Formula One Turbo Era, BMW Used Old Seasoned Cast Iron 4 Cylinder 90CID/1500ccd Turbo Engines. At + 5 Bar circa 1500 HP on 102 RON Gasoline.
@gerhardstrydom8620
@gerhardstrydom8620 26 днів тому
You forgot to mention rotary engines.
@P71ScrewHead
@P71ScrewHead 22 дні тому
They suk..lol jjk..
@christopherjones512
@christopherjones512 27 днів тому
Iron is the best
@BonnieKay13
@BonnieKay13 18 днів тому
Aluminum has only two places; pop cans and airplanes and that's IT ~~
@markellrobinson4447
@markellrobinson4447 Місяць тому
Will aluminum engines catch fire over time? I'm bout to purchase a 6.2 Lt
@christian-agk-dts-google-map
@christian-agk-dts-google-map 2 місяці тому
AGK DTS Hypo Economist Konzept Institut maison des associations Thüringen united Germany.
@chrisgoat6435
@chrisgoat6435 2 місяці тому
Schweig.
@vernonslone8627
@vernonslone8627 Місяць тому
Myself aluminum is better because it can be repaired easier than cast iron....I always wondered why they never used cast steel instead of iron.... You could weld that....
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
A cracked block can't be repaired. Aluminum blocks always have a much shorter lifespan.
@carlthornton3076
@carlthornton3076 29 днів тому
Very Good!... #113 ✝ {4-4-2024}
@kenc3288
@kenc3288 Місяць тому
AluminIUm
@jackbn9353
@jackbn9353 Місяць тому
When comparing two items, one may be better, but neither is best.
@danthurman9076
@danthurman9076 Місяць тому
Cast Iron
@hildablanco1591
@hildablanco1591 Місяць тому
Titanium is good for marine use and straight 6 or 8 is best with OHV and flat engine blocks suck too much cylinder wear and valve wear
@myronboone84
@myronboone84 19 днів тому
Aluminum block four seasons
@babaoreally8220
@babaoreally8220 Місяць тому
100-150# off the front of the car.
@outsider7658
@outsider7658 Місяць тому
Sorry to be a party pooper: You have smoked something strange! For the first: the inline six, has the most perfect balance, between primary and secondary imbalances! For the second: Most aluminium engines are in built in several layers, they are like a cake, not a single block, like iron blocks. Take a look at a Volvo or VW engine. from a Finn in Diaspora
@richardschipper5989
@richardschipper5989 29 днів тому
wrong
@mvnorsel6354
@mvnorsel6354 2 місяці тому
Never had alloy always cast iron.
@resjon7981
@resjon7981 26 днів тому
Metal engine blocks are best.
@TexasNationalist1836
@TexasNationalist1836 21 день тому
Wooden engine block
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
As opposed to wood or plastic, yes.
@Bugsworth
@Bugsworth Місяць тому
Titanium is hard to machine. The tooling costs are astronomical, hence expensive to buy but low scrap price... ( was, but i am an old timer)
@6catalina0
@6catalina0 Місяць тому
Cast iron engine block and cast iron cylinder heads == no blown head gaskets.
@richardschipper5989
@richardschipper5989 29 днів тому
that's totally false, I've blown way more gaskets on iron then aluminum
@Lexicoyote
@Lexicoyote 2 місяці тому
Also get more torque on online blocks and even ware on the cylinder walls . That’s why the Toyota Super-a inline blocks put out super car power with their turbos ….😂😂😂😂
@chrissullivan5752
@chrissullivan5752 20 днів тому
Chevy Vega
@WarbirdPhoenix
@WarbirdPhoenix Місяць тому
I would opt for a hybrid block made of iron,aluminum,and titanium, but my wallet left the chat.
@edongbato9234
@edongbato9234 Місяць тому
Does Aluminum blocks burns oil?
@MikeM-oq9pz
@MikeM-oq9pz Місяць тому
No, aluminum blocks do not "burn oil' if proper oil change procedures are followed. It all depends on the piston ring material as some newer engines have piston rings that have low tension in the cylinder block, and these can cause oil burning problems at higher mileage moreso than the aluminum.
@josepholiver6733
@josepholiver6733 2 місяці тому
What about when it’s cold I heard a aluminum block will flex a little vs a steal or cast iron will just crack
@shadowopsairman1583
@shadowopsairman1583 Місяць тому
Been through several cold spouts and never had a problem
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
Actually, the aluminum block is notorious for cracking, not the cast iron.
@darrenhankner5282
@darrenhankner5282 23 дні тому
cast iron. aluminum is lighter but not stronger
@71Fenderv22
@71Fenderv22 Місяць тому
Iron block for me always, with special care taken when aluminum heads are added to the build. The only time I would go with all aluminum would be in a serious racing N/A build, where weight savings matter and rebuilds every-so-often are expected.
@giles-df9yu
@giles-df9yu Місяць тому
I had no idea a vw was a performance vehicle
@rogerdodrill4733
@rogerdodrill4733 Місяць тому
They be racing long time ,europe
@richards.mchardy3556
@richards.mchardy3556 22 дні тому
Cast iron
@Lamaton
@Lamaton Місяць тому
my choice is a block made of chrome alloy steel
@alaaaldafrawy6837
@alaaaldafrawy6837 Місяць тому
In the future they will make it from plastic 😂
@Support_Ad_Blocker
@Support_Ad_Blocker Місяць тому
Ford probably already is.....
@rc4a0frios
@rc4a0frios 20 днів тому
Plastic is bad for the enviromente. They will make it out of cardboard.
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
I wouldn't be surprised. They already make part of their truck radiators plastic, so they can make more money on replacement parts. Also door handles & several other things.
@Lexicoyote
@Lexicoyote 2 місяці тому
Inline blocks don’t ware the cylinders walls like v blocks….
@cavscout62
@cavscout62 Місяць тому
You mean Wear.
@perpetualgrin5804
@perpetualgrin5804 19 днів тому
There are no aluminium submarines😅.
@RogerSamuel2023
@RogerSamuel2023 26 днів тому
Aluminium is best it's lighter and keeps radiator cleaner
@Fred-mp1vf
@Fred-mp1vf 19 днів тому
Until it cracks and you have to pay $20,000 or more to replace it!
@vadakkan6390
@vadakkan6390 2 місяці тому
1st comment
@hiwe4ka503
@hiwe4ka503 2 місяці тому
for children it is important?
@Support_Ad_Blocker
@Support_Ad_Blocker Місяць тому
vadakkan6390 where is the comment?
@Support_Ad_Blocker
@Support_Ad_Blocker Місяць тому
he's 35 and nervous because something hasn't “dropped” yet.....😂😂
@eligiotello9337
@eligiotello9337 6 днів тому
Duh.
@markquiswest6607
@markquiswest6607 2 місяці тому
They need to start back making Cast Iron Engine Blocks back on American Vehicles, instead of the Piece of Shit Aluminum!
@michaelbenardo5695
@michaelbenardo5695 Місяць тому
That will only happen if we can force a ban on foreign cars and scale back CAFE, and encourage American producers to engage in Saturation Advertising the way the Japanese are doing.
@shadowopsairman1583
@shadowopsairman1583 Місяць тому
AL is for cars to me
@julijanmagda7855
@julijanmagda7855 Місяць тому
Hard recicled plastik block with cooling panel 3nd fire holl for cilinder if you want totaly madnes of old technology on fuel gas or watter,,,,to many weigt components end lousing power,,,the vest us Neodium generator you hawe light mashine big power little heating end plus energyvend xxx combination gor a worck in or out...no tank no senzirs no IT no noting but from a to b in continuum 100 years PS Trouble us better shell for a car end tures witch can run 100 years
@imansohrabi7068
@imansohrabi7068 Місяць тому
I perfer iron block.i always buy a car with iron block engine
@terrymarshall5480
@terrymarshall5480 Місяць тому
Gray cast... aluminum is junk...cheap and lite wait.
@rustypliers74
@rustypliers74 Місяць тому
Learn how to spell.
@realtree297
@realtree297 Місяць тому
Ford triton v-8 with aluminum heads, spark plug blowing pieces of garbage Typical: Found On Road Dead
@Support_Ad_Blocker
@Support_Ad_Blocker Місяць тому
Fix Or Repair Daily Found Off Road Dead (looking at the Raptor fanboys)😂😂😂
@dickheder4940
@dickheder4940 Місяць тому
cast iron for diesel engines
FWD vs RWD vs 4WD vs AWD What's The Difference? Which is Better?
17:27
The Engineers Post
Переглядів 2,1 млн
😱СНЯЛ ФИКСИКОВ НА КАМЕРУ‼️
00:35
OMG DEN
Переглядів 1,3 млн
КИРПИЧ ОБ ГОЛОВУ #shorts
00:24
Паша Осадчий
Переглядів 4,5 млн
I PUT MY ARMOR ON (Creeper) (PG Version)
00:19
Sam Green
Переглядів 5 млн
How to fix Bike tubes amazing must watch #viralshorts #trendingshorts
1:01
STEEL vs ALUMINUM vs TITANIUM Connecting Rods
19:17
driving 4 answers
Переглядів 956 тис.
German Giants: Mega Engine Manufacturing | FD Engineering
49:04
Free Documentary - Engineering
Переглядів 297 тис.
Toyota CEO: "Our New Engine Is The End Of The Whole EV Industry!"
11:20
Cylinder Offset Changes Everything
23:45
driving 4 answers
Переглядів 2,4 млн
BMW Engine Block Casting | HOW IT'S MADE
11:22
Cars Garage
Переглядів 3,9 млн
Why Different Car Engine Placements Matter | Explained
14:37
The Engineers Post
Переглядів 38 тис.
😱СНЯЛ ФИКСИКОВ НА КАМЕРУ‼️
00:35
OMG DEN
Переглядів 1,3 млн