3 reasons why this turbo kit doesn't work. 1. WG valve flap is open so it does not generate any boost. (You can see how loose it is at 16:08) 2. blow through system without fuel pressure compensation will work for a few seconds until the boost returns all the fuel from the carburetor to the tank. 3. oil drain from the turbo. Do you really expect that some magical force will push the turbo oil uphill into the tank? The fact that there is no smoke in the video is probably the result of the fact that the fuel pump that is supposed to pump the oil probably cannot pump the oil to the turbine. Do not get me wrong. It's not that I'm criticizing your work. But when you do something, try not to make basic mistakes that would be noticed by someone who knows something about it. Your turbo kit may work, but it requires some work. My suggested solutions to the problem 1. Weld the WG (you have no control over the boost) or reinstall the actuator 2. There are two options. Fuel pump (min. 1bar/15psi) with a fuel pressure regulator or a simpler method like in RC models, connect the boost from the intake to the fuel tank. Fuel pressure must increase with boost. 3. There are also two options. Second return pump or install the receiver below the turbocharger. And make sure oil is flowing to turbocharger. If there is a problem with this, try using oil with a lower viscosity, e.g. 0w8 or 2t or mix diesel fuel + oil.

Only problem here: it simply won't make extra HP with that wastegate arm flopping around with no actuator. It's going to be both an exhaust and intake restriction.

I'm trying to work out why you removed the wastegate actuator. There's nothing regulating the amount of boost from the turbo any more. It works both ways, maintaining backpressure in the turbo to spool it up, then reliving excess boost to stop you nuking the engine. In the end, you've added a bigger carburettor and a fan in the exhaust that's not doing anything meaningful but generate noise to 'sound more powerful'.

Calling BS on this video, The wastegate is hanging open so its making absolutely no boost, and you have a blow-through setup which will not work for gravity fed fueling. You need a pull through set up, but then again, puting a turbo designed for a 1-2 litre engine on a 200cc engine wont yield results anyway, as it cannot put out enough exhaust volume to get the turbine spinning fast enough to make any real boost.

Wastegate actuator left the chat. Still working as N/A 🤷🏻‍♂️

Blow through carb setup with no fuel pump, carb vent lines open, turbo waste gate open. Fabricating skills 10/10. Engine, turbo and carb knowledge 0/10

The improvement here is from the carb and removal of the governor control, not the turbo.

Nooo, you must put the carburetor BEFORE the turbo, otherwise the pressure from the turbo will push the fuel back from the carburetor, hence make less power. so the "extra power" you feel is just because you've upgraded the carburetor

I think all the power increase you got was just from the new carb, the waste gate is open so you're getting no boost, would be a good thing to add a boost gauge and see how much you're actually getting.

Problems: 1. pressurized carb - pushes fuel back to the tank on boost 2. wastegate - should be closed or set to open at specific pressure 3. turbo size - way too big for 200cc engine It revs higher because of bigger carb, not by the boost. I'd like to see dyno session before and after

the wastegate valve without the wg actuator it's always in open bro :D so the turbo not boosting...

Did you really leave the wastegate open, the turbo can't work

Painfull to look at when you know something about turbocharged engines

funny idea, but here it's only for decoration

you forgot to close the wastegate....

Change to a blow through carb and wire the wastegate closed. Then full send it. This was a waste of effort and fab skills. No sub for you.

Can’t put boost thru a carb that way. When it turns from vacuum to boost it will force fuel the wrong direction thru the jets and blow fuel out the float bowl vent pipes. You have to add a small vaccuum hose and direct pressure to the float bowl vents to equalize pressure inside the float bowl when under boost. Besides that it can be made to work!

Sorry got to call Bull shit on this! having done this for a living, built many turbo motorcycles and car engines, this video looks great if you have no ideal whats going on! here are the issues, 1: you cant gravity feed fuel to a blow through carby set up! fuel pressure needs to be higher than boost pressure or the fuel wont flow into the foat bowl. 2: some sort of fuel enrichment needs to happen when on boost, additional boost pressure needs to be sent to fuel bowl under boost as well as aditional fuel pressure. 3: with out ignition retard on boost or very high octane fuel, this engine will detonate it self to death 4: this engines, internal splash oil lubrication wont work well under the additional load of turbo charging. 5: to make more engine power the engine must see boost ! hard for a turbo to do that when you didnt fit the waste gate ! i am gueesing the engine would not run due the the mentioned carby issues so to make this turbo engine run, he had to remove the waste gate controller! that means no boost. no boost no additinal hp made, so a total waste of time! this video is nothing more than a deception , the guy making this video has no idea!

Nice build but the turbo system didn't do anything at all.😅 First of all it doesn't make boost because the wastegate is always open, second if it made boost it wouldn't work just like that. The turbo oil drain has to be higher than the tank. The only thing that made the engine a little more aggressive is that PWK.😅😅

“ Now , the engine looks like much more powerful “ :)

Not a bad job but it looks like the only power gain was from the slide carburetor and governor bypass...both allowing it to rev past 3-3600 rpms. It certainly didn't sound like it was making boost.

Who the hell has a parts counter in their shop? I'm just happy to have a beer fridge in mine!

You can play with the wastegate for more boost and power. (Always checking the boost pressure). Nice job!!!

Your coolest projects really look like a cool update to that racing tractor. always fun to watch your videos. enjoy your weekend. 😘🤠❄️🇳🇱

Yeah....we don't need no stinkin' waste gate! LOL😂🤣😆🤣

How's it make boost with the waste gate flapping around?

The carb should go on the intake of the turbocharger and then into the engine

Along with multiple other problems with this build, the Turbo oil drain can not be higher then the turbo.

How not to install a turbo: This guy actualy made the engine worse.

I think we all want to see more about your project bmw pickup

11:04 okay i see what people are bitching about now. He obviously assumed the standard wastegate would build too much psi and blow the motor apart. So he either needs to install some sort of electronic boost controller or a lower pressure waste gate. Unfortunately yes this engine wont make any boost and youll actually have put a big drain on it by restricting air intake and exhaust with longer tubes and a turbine

get a double-throw switch. run ground to the center of the switch. run one side of the switch to the engine kill wire, and run the other side of the switch to the pump ground. run A FUSED WIRE from battery positive to the pump positive. switch on = oilpump on and "run" switch off = oilpump off and engine-kill. you wont be able to run the engine without the oil pump switched on!

Turbo is too large. Even if it was smaller, here are things he got wrong. 1-Wastegate open. (There cannot be more air-fuel mixture in engine during power stroke. Which is the whole point of turbo) 2-Too little oil in the system (oil went to hoses and did not add more.) 3-Oil volume for turbo is too low, and does not have filter. And due to low volume of oil, it will get too hot. 4-carburator needs to be before turbo intake 5-engine is aircooled, and it probably melts after short period (assuming all the problems regarding turbo are fixed) Nice idea. And nicely fabricated parts using simple tools. Unfortunately it was more like 5-minute crafts. Pointless hand waving, without intention to success.

Take off the carb and mount it on the turbo inlet and remove the Wastegate

I'd have to see before and after dyno results for this before I believe one word of it!

The oil for the turbo needs a cooler and a filter

Guy could probaly sell some of his grinder disc and wire brush collection and buy a HF plasma cutter! I know his wife and neighbors would appreciate it!!

Unfortunately putting that turbo on that engine has done nothing for performance. You have just added weight, if it ever put the waste gate back on it so it could develop boost then it will go lean from the pressure blowing fuel out. Put the carb the other side of the turbo and put the waste gate back on then it will be interesting 👌🏼

"Be careful disassembling a turbo" *whacks it with a hammer several times*

There are so many things wrong in this video... That turbo oil drain, how is that going to work? And that carb..? 🙈

even though the carb is the only real power gain its still looks cool just need to do some modifcations and revision

The carburetor must be installed before the turbocharger

Oilcooler? Wastegate Rod?

Did you do this just for views? The way you have it, takes power from the engine. Without control over wastegate flap it makes nothing.

Hey bro not working turbo , westgate is open

drinling into paint putting screws without painting before rust is going to love this project

Love the editing! Congratulations mate...From OzTralia

14:32 wastegate disconected and open, thats is making no power

all that work then disconnected the wastegate and making literally 0 psi and probably losing power

Love the build, but I don't think the exhaust flow will be enough to do much with that size turbo. Which is good since if it did, that engine would definitely toss a cranck 😅😊

one of my favorite things to do when i get any small motor, a lawnmower, or a go kart, is port and polish the heads. easy tiny torque gain, and everytime i sell it, extra money

Best upgrade ever 🤩👍

A Wastegate nie otwarte i turbo nie pompuje

The carby has to fit before the turbo not between turbo and engine

The tractor looks awesome, and as one other commenter said, your fab skillz are 10/10. But yes, a mechanical fuel fump with a greater psi rating (by at least what the engine needs to run N/A) would make it so that turbno (yes, i spelled it that way on purpose) would actually add boost. It also needs a small intercooler. Think stock Suburu WRX/Suzuki Alto Works style, or even a larger sized heater core if that youtubesteak skrill is running thin.

The turbine gate appears to be open. If the actuator is not controlled, no boost will be applied.

Amazing! Thank you for sharing this video. Greetings from Madang, Papua New Guinea!

I turbocharger a scott bonnar lawn mower as a kid on methanol fuel. I love everything about this. Few changes and you'll get that thing rocking. ❤❤❤

Boost gauge will tell you without the wastegate shut you have a exhaust restriction and more vacuum than stock

As Jeremy Clarkson always said, 'what bad can happen?'

you need to weld the waste gate closed it wont be making any boost.

Nice i wait for this video long time its useless but its freaking cooool

100% did not work. you can NOT run a carb on a turbo build without a fuel pressure regulation system

0 boosta a w dodatku tylko dławi ten silnik przez brak paliwa (to tylko moja opinia)

There's no way you will get any boost. The weight of that turbo alone will slow the whole thing down.

You need to re-jet your carb. My son and I and our friends build racing mini bikes with 212cc motors all the time. If your carb came with a jet kit make sure that you check to see which one came pre-installed on the carb because we have to change the jets to like a 130 sometimes a bit lower but you will get the most horsepower out of it and it will run smoothly.

Nope! Fake! No boost was being made! The wastegate was left open and all the exhaust pressure was escaping around the turbo. Even if the turbo wastegate was welded closed, or something, the boost would have pushed gas backwards into the fuel tank. That carburetor is on the wrong side of the turbo. 🤦‍♂️ Fake!

It looks like a fun build, good job

Everything is great! Except for the air filter 🤯🤯🤯

turbo oil drain has to be bellow turbo, if wastegate is always open then u arnt making enough boost etc etc

too cool.. I would have added a fuel filter and oil filter. I think a stater would be a good idea to keep the oil pump battery charging, then you could add lights too

L'aumento di potenza è legato al carburatore, la turbina non va in pressione perchè se così fosse la benzina uscirebbe dai fori di compensazione presenti ei lati della vaschetta del carburatore.

The waste gate was left loose so this thing wasn't doing anything except running stock with the weight of a turbo just sitting there doing nothing except spooling up and making nothing for power.

Nice little project I have a Honda Grom that I just put a tiny turbo on fun to race around town on

Just for fun only, no boost 😂

Привет!интересное решение,лайк 👍.теперь нужно электростартер,и глушилку на панель сделать.

Carby in the wrong spot 😂

Sve pohvale majstore🥇👍👍👍

Exelente, te ganaste un suscriptor👍🏽

Наддув не работает. Нужно увеличивать подачу топлива вместе с воздухом. У вас в карбюратор топливо поступает самотеком. При наддуве оно перестанет поступать.

Nice job, looks like you need a on dash on and off switch and a longer pull rope for better access.

"And that's it!" Like this was a 3-step process. XD

It doesnt lack power it lacks suspension 😂😂

Definitely not a DIY turbo instruction video, far to many things done wrong, not different, wrong.

BS video, ppl aint stupid knowing the setup didnt work and you have the wastegate hanging. Go put the carb in front of the turbo and hook up the gate

Need to remove governor, install billet flywheel, billet connecting rod, stronger valve springs and performance camshaft for high RPM.

How is generating boost with wastegate opened?

Not sure what kind of plumbing i just watched, but the editing sure made an entertaining watch.

Создавать давление в карбюраторе не имеет смысла. Раньше применялась схема, где карбюратор стоял перед турбиной на впуске. Из минусов, обмерзание при температуре ниже 5 градусов по Цельсию.

Now it needs a intercooler

Sounds like it's barely even running, turbo needs to be after the carb in a non pressure-fed setup.

as soon as i seen there was no possibility of compression i lost interest

What about electric start ??

einen Turbolader über einen Vergaser laufen zu lassen - das wäre der Erste, der das könnte. Außerdem ist der Turbolader als solcher auf einen Motor abgestimmt - dieser hier scheint von einem PKW zu sein - der muss doch erst mal eine bestimmte Abgasmenge bringen um den Lader zu betreiben - also alles was Recht ist - liebe Grüße an die Physik

Where is fuel pressure coming from under boost?

Taj turbo neradi bez West Gate dobivena snaga je samo do Karbosa ne od turba on radi u prazno,ostalo sve sta radis Topp,Topp

Love it. I need a garden tractor

Honda makes a true turbo lawnmower engine

Nice try kid but if it was making ANY boost it would not run! It would pressurize the carb and not let any fuel into it.

If u wanna add some healt in it you can put a mudguard to the airfilter side!