Bosch 12V Battery Upgrade from Nicd to Lithium-ion

  Переглядів 221,130

Gear Show

Gear Show

2 роки тому

This drill was abandoned in Japan, because its battery was dead. I just convert the battery from Nicad to Li-ion, it works very well.
Original Battery
- 12 cells of Nicd 1.2V
- Voltage 12V ~ 13V
- Capacity 1.2 Ah
New Battery
- 6 cells of Lithium-ion 3.7v 3000mAh
- Voltage 11.1V ~ 12.6V
- Capacity 6Ah
Original Charger
- Output voltage range 7.2V ~ 14.4V
- Input 100V
New Charger
- Output voltage only 12.6V
- Input 100V/240V
BMS 3S20A is a battery management system for 12V battery pack
Lithium-ion battery cell
- Brand model: LG INR18650HG2
- Standard capacity: 2800- 3000mAh
- Rated voltage: 3.6V
- Charging voltage: 4.2±0.05V
- Maximum continuous discharge current: 20A
- Discharge cut-off voltage: 2.5V
- Weight: Max.47.0g
- Size: Max.18.2×65.2 mm
- Charge and discharge times: 500 times
I hope you find this video useful and enjoy it!
I am happy to receive feedback, suggestions to improve myself.
!!! I'm sorry for the mistake if I did in this video !!!
** I still keep some parts, I want to help the world environment **
Thank you very much for your likes, comments, and subscription!
Have a nice day
Gear Show

КОМЕНТАРІ: 151
@xarogath
@xarogath 2 роки тому
Hey I have the same drill, the bateries are almost dead, now I have a tutorial on how to convert it to Li-ion, thank you :D
@prasadvn524
@prasadvn524 2 роки тому
Love the new spot welder and of course the conversion
@MYs0708
@MYs0708 2 роки тому
Now, I'll call you "The King Of Battery" 👍
@alexandres8846
@alexandres8846 2 роки тому
good job mr gear i like the conversion of tools 100 ac to 18 volts without cable they are great!
@YassineKAOUANE
@YassineKAOUANE 9 місяців тому
Nicely done. And it fast charges the cells if you're in a hurry.
@Mladjasmilic
@Mladjasmilic 2 роки тому
I did similar thing to 14.4V system, put 3 in series Li-ions for 12.8V. But I kept most of original charger circuit, just added buck converter with current limiting feature. I wired constant current wire to charging LED and constant voltage to charged LED. My settings were 12.8V and limit 1A.
@Tegelane5
@Tegelane5 5 місяців тому
It's safer that way (voltage to battery is controlled by charger aswell) but with BMS it cuts charging out when cells are fully charged-charger just "thinks" that battery was taken out. This way charger can be used to charge old and new (lithium) batteries.
@amilcarmoncada1801
@amilcarmoncada1801 2 роки тому
Estupenda actualización de batería Bosch 12V de Nicd a iones de litio, respetos desde Venezuela.💯🤜🔥🤛👍💯
@sthenzel
@sthenzel 2 роки тому
NiCds should be thrown out anyway, but the Bosch chargers I know do flash green while charging, even with brand new batteries.
@JuanPerez-ne4sq
@JuanPerez-ne4sq 2 роки тому
1:10 SURPRISE!
@yeagerxp
@yeagerxp 2 роки тому
Nicely done 👍👍👍Thanks for sharing
@user-vi9so6td3c
@user-vi9so6td3c 2 роки тому
Hervorragende wissenschaftliche Erklärung, danke
@nicub.1595
@nicub.1595 2 роки тому
Very nice tool. Great job 👍👍👍
@LAVINCHO1
@LAVINCHO1 2 роки тому
Impeccable thanks for sharing your knowledge I watch all your videos and I learned a lot, a query that recommends when the starting peak of a motor blocks the bms eg 3S 60Amp, puts a capacitor between + and - to absorb those inrush, of what value would it be the capacitor to be polarized or not? thank you from Uruguay
@amshabeeb6133
@amshabeeb6133 2 роки тому
Excellent quality job 😀
@getyourkicksagain
@getyourkicksagain 2 роки тому
Everything OK, friend? This conversion was great, as usual, but it seemed rushed and not as careful as your other projects. I hope you and your family are well. Thanks for your videos!
@leko2138
@leko2138 2 роки тому
Thank you man i had the same drill with your video i fix it it works just like new
@justarideout
@justarideout 2 роки тому
A pleasure watch a true craftsman
@gear_show
@gear_show 2 роки тому
Thank you!
@kret63
@kret63 2 роки тому
Tested on bulletproof piece of steel! Good idea with the charger. Keep on filming!
@gear_show
@gear_show 2 роки тому
Thank you! I'glad you like it.
@taunteratwill1787
@taunteratwill1787 2 роки тому
So happy you did this!! Only 12500 people on UKposts did it before you. 🤣
@rabk5702
@rabk5702 2 роки тому
I have the same model drill battery's and charger same problem battery's are knackered drill still working fine must get them sorted to good a drill to leave unused great posting as per usual :-)
@gear_show
@gear_show 2 роки тому
Good to know, I'm glad it helps you!
@rahmiyilmaz957
@rahmiyilmaz957 2 роки тому
What drills can we use the 20a bms for, it has probably already passed the toughest test
@parvizzargari9183
@parvizzargari9183 2 роки тому
Very nice job man .you are the king
@RyeOnHam
@RyeOnHam 2 роки тому
Nice. I would have skipped the NiCad charger and put the charging ports directly into the batteries. Looked like enough room in the front of the batteries.
@dctech786
@dctech786 2 роки тому
The video is most interesting but i suggest the orignal charger can also charge this converted li ion batteries because its 14.4 v charger.
@piciuflorentin9939
@piciuflorentin9939 Рік тому
Excellent video/job. Just 1 thing that wasn't clear, and would've loved explained, as for a newbie in electronics like me: the changes done on the charger itself. That I didn't understood at all...
@tduic
@tduic Рік тому
Hi, I admire your work and videos. I have an exact same drill with the same problem: dead batteries. I want to do the same as you. But I have two questions: 1. What is the power (current) requirement of this drill? I haven't be able to find the specs. Your BMS can deliever 20A, which multiplied by 12V gives 240W. Isn't that a bit low? 2. Having a 2P configuration with 20A batteries, they should be able to deliver 40A output, so why did you limit it with 20A BMS instead of putting 40A version? Thank you for your answer, maybe I'm wrong, I'd like to learn and understand things before I get to work.
@rahmiyilmaz957
@rahmiyilmaz957 2 роки тому
I also used 3s20 amps bms for the same drill, but the drill does not work when I press the trigger all of a sudden, the pressure works slowly, when I try the batteries with 3s40a bms, there is no problem, but there is a problem with 20a bms, where is the problem?
@user-vi9so6td3c
@user-vi9so6td3c 2 роки тому
Ich habe eine Frage, warum haben Sie den Schraubendreher auf der Originalladeplatine verwendet, bevor Sie die roten und schwarzen Drähte daran gelötet haben. Hast du einen versteckten Draht durchtrennt??? Ist das notwendig???
@user-kt2hb8xr3p
@user-kt2hb8xr3p 2 роки тому
thank you teacher
@FerSniper
@FerSniper 2 роки тому
Круто!!! Спасибо за видео!!!
@valmirramos4195
@valmirramos4195 2 роки тому
Gratidão GearShow!
@marcoantoniopomolgomez4921
@marcoantoniopomolgomez4921 2 роки тому
Where can I get the Li-on charger an the other accesories? Could yoi send me the link, please?
@contemarco8218
@contemarco8218 Рік тому
congratulations for the work. could you put the links for buying the batteries, control board and charger? Thank you
@tototelek7768
@tototelek7768 2 роки тому
Do I have to change the charger after upgrading the battery..?
@nutzeeer
@nutzeeer Рік тому
I wonder if its economically viable to do this. I have 2 old NiCD drills!
@tankimpoh7212
@tankimpoh7212 2 роки тому
hi i saw you use the batteries/electrical drill ( the white color one ) could i ask for the brand and name thank you so much. please continue to do these repair im a beginner and like to learn more, wish if there's an discord or a place to chat in the future thank you . you are awesome
@chazy10
@chazy10 2 роки тому
Why you deleted the part of the connection from battery to PCB?!
@zebrafinchaviary6726
@zebrafinchaviary6726 2 роки тому
Eline sağlık
@myrestorations
@myrestorations 2 роки тому
I like it very much 👏
@DigitalBhangari
@DigitalBhangari 2 роки тому
How about corded rotary tool to cordless?
@marcelolobato8368
@marcelolobato8368 2 роки тому
Nice job
@gear_show
@gear_show 2 роки тому
Thank you! Cheers!
@TheMssFoxy
@TheMssFoxy 2 роки тому
It would be amazing if you could put subtitles during the video explaining what you are doing.
@MrStyle-sr1yv
@MrStyle-sr1yv Рік тому
CAN I USE 5S BATTERY PACK ?? CAN THE 12V DRILL HANDLE 20V ?? FOR ME 5S BMS WITH CHARGER IS EASIER
@jysndc9592
@jysndc9592 2 роки тому
Wow . LG Choco. Can also be used for vaping. 😁
@jorgealbertovelasco336
@jorgealbertovelasco336 2 роки тому
Ve CHAPLIN WAS BRILLIANT WITH HIS SILENT MOVIES. Only an |D|07 makes a video of this nature without a descriptive. I hate to say it, but you qualify as one !
@annabiagetti549
@annabiagetti549 Рік тому
hi,, I have a bosh gsb 18v VE-2 old ni-cd 3000mah, possible convert it ? what battery charger protection system pcb I need use ? how much cell I need ? thanks
@nextstageotomotif1411
@nextstageotomotif1411 2 роки тому
Where did you buy this sir...?? Can you shipping to my county Indonesia..
@realsciences8459
@realsciences8459 2 роки тому
Thank you very much friend about this video Please can you show me where i can buy like this cell li-ion 3.7 And how can i know it original or fak
@mike3427
@mike3427 Рік тому
nice work
@gear_show
@gear_show Рік тому
Thank you!
@Manu-nr1yt
@Manu-nr1yt 2 роки тому
You should not keep one old cell in there. It would be so much nicer if you replaced it with something that can't leak over time.
@DaftOldMan
@DaftOldMan 2 роки тому
I use a piece of UK overflow plastic pipe.
@mariaassuntadinucci-io8ze
@mariaassuntadinucci-io8ze Рік тому
Dove posso trovare i vari componenti puoi mettere i link? Grazie e complimenti
@kant219
@kant219 Рік тому
Sir, I want one clarification. In the video, the previous drill charger charges ni-cd batterie pack. But after changing to lithium ion batteries, as you showed in the video. Can the previous drill charger charge the replaced batteries.
@mauroriviezzo7289
@mauroriviezzo7289 10 місяців тому
Si lo può fare l'importante è non dare un alimentazione di troppi A il voltaggio può variare di poco o essere superiore o essere lo stesso 12v mai superare i 3A altrimenti potrebbe scoppiare una batteria
@Endosome0918
@Endosome0918 2 роки тому
請問您是住在日本嗎? 怎麼拿得到這麼多日本製的舊電子產品, 我之前看您的影片Bosch PDR , 修好我從回收廠撿回來的Bosch GDR 14.4 調速開關一樣是壞的,只能最高速~但這樣鎖螺絲容易滑牙弄壞螺絲頭 我發現其實大多速的調速開關是通用的, 只是大小形狀不同,要修改~ 淘寶有類似Bosch的開關可以買來改 來自台灣的粉絲留~
@quattrocchi71
@quattrocchi71 День тому
Spettacolare sembri una fabbrica come nuovo
@maiklmaly
@maiklmaly 2 роки тому
I did same upgrade with batteries, but charger left it in its original condition . No functional problems (maybe slower charging)
@Yorumcu63
@Yorumcu63 Рік тому
Master if old Ni-Cd charger circuit PCB have TL431 code component(Like BC series transistors) you can adjust output voltage for Li,-Ion batterys .I think you can adjust on old adapter with trimpot LED indicator too (LED on is charging ,LED off is charge done ) (Only you will change 2 resistance value.You an find details in youtube videos for TL431 output voltage adjust).So not need any new Li-Ion charger. If have not TL431 component in old Nİ-Cd adapter ,you can remove last section components (after bridge and big capacitor circuit ) and you can connect XL6009 DC-DC converter to removed area and you can adjust output voltage on chip module
@m0sh1994
@m0sh1994 2 роки тому
the table knock sound is very loud ,pleas low it later i hope to make a video of turn the angel grinder from 220 v to common dc voltage battery by rewinding method... thanks
@ovillaturunen6285
@ovillaturunen6285 2 роки тому
Very nice!!!!!!!!!!
@gear_show
@gear_show 2 роки тому
Thank you! Cheers!
@mikanikolic1976
@mikanikolic1976 2 роки тому
Fume extractor with tripod..good idea!!!
@RestoredChannel
@RestoredChannel 2 роки тому
Just when I needed something to watch 😎
@quattrocchi71
@quattrocchi71 День тому
Stesso trapano con batterie andate vale la pena recuperarlo?
@prakashsuryawanshi6211
@prakashsuryawanshi6211 2 роки тому
What are the voltage of each battery ,what modifications done in old charger. Pl explain to easy language
@Jnes01
@Jnes01 2 роки тому
I am not an expert but there are 6 batteries, each having 4.2V when charged. The batteries are wired in pairs. Each pair is in parallel, and the pairs are in series. This makes the total charged voltage 4.2V x 3 = 12.6V. For the old charger he destroyed the traces on the charging circuit so that it was no longer connected, then he soldered wires to the contacts for the battery pack. These wires lead to the barrel connector jack where he connects the new charger, which is an AC to DC power brick that outputs 12.6V to charge the new battery.
@prakashsuryawanshi6211
@prakashsuryawanshi6211 2 роки тому
@@Jnes01 Thank you so much for giving good information
@user-hl7mc9pq4p
@user-hl7mc9pq4p Рік тому
Для 12 вольтового вполне хватает 3 высокотоковых аккумуляторов и плата вмs 3с40а и работает как часики
@sanjayghugre8731
@sanjayghugre8731 2 роки тому
Nice
@sanjayghugre8731
@sanjayghugre8731 2 роки тому
आशि बनून मिळेका
@mustafabhopalwala4375
@mustafabhopalwala4375 2 роки тому
❤️
@gear_show
@gear_show 2 роки тому
❤️
@glenjoyalejo9488
@glenjoyalejo9488 2 роки тому
nice
@congvi5702
@congvi5702 2 роки тому
Mạch này nhận sạc zin luôn hả bạn
@dominiquenogueras3785
@dominiquenogueras3785 2 роки тому
Can I send you my power drill? I would love to se le the drill alive again!
@mateuswjs436
@mateuswjs436 2 роки тому
Vc mora onde ?
@djamelhamdia134
@djamelhamdia134 2 роки тому
You should throw away the NiCd battery, it will leak and oxidize with time and ruin the entire battery pack. A piece of PVC pipe would work very well.
@hazgajocom655
@hazgajocom655 2 роки тому
👍👍
@DewloN
@DewloN Місяць тому
Hello. Thanks for the video, it's interesting. But in my opinion this particular BMS is a bad solution. The DW01 control chip will turn on the current blocking when it reaches 75A, because 0.150V/0.002R=75A. Are you sure that this screwdriver needs 75A*~10V=750W power? The DW01 control chip turns on blocking when discharging to 2.4V - this is a lethal voltage for 18650. The DW01 control chip believes that batteries can be charged up to 4.28V - this is also bad.
@vehiculeselectriques
@vehiculeselectriques Рік тому
you used a BMS so the original nicad charger will make the job with no or very little modification ;^)
@pavelstepanek9818
@pavelstepanek9818 2 роки тому
Zdravím mužů nabíjet lipol 3s 5200mah nabíječku 2A 12.6v děkuji za info
@bboorttv4181
@bboorttv4181 Рік тому
Hey bro hru.. nice videos.. what do you call that green board?
@gear_show
@gear_show Рік тому
Hello, that green board call BMS (Battery Management System). It is used to control all battery cell.
@bboorttv4181
@bboorttv4181 Рік тому
@@gear_show thank you so much bro.. have a good day..
@kerim148ozturk
@kerim148ozturk Рік тому
Li ion battery👍👍
@Akc64
@Akc64 2 роки тому
I have seems like that 😁
@lightbatmen
@lightbatmen 2 роки тому
6:17 Шайтанама!
@servistools5691
@servistools5691 2 роки тому
👍
@chriscraft9681
@chriscraft9681 2 роки тому
👍😉
@arturlend2297
@arturlend2297 2 роки тому
👍👍👍😎
@rezafazrie2298
@rezafazrie2298 2 роки тому
👍👍👍👍👍👍
@mechekalabd6492
@mechekalabd6492 2 роки тому
احسنت. واصل
@gear_show
@gear_show 2 роки тому
شكرا لك!
@lolcec81
@lolcec81 2 роки тому
Комментарий в поддержку видео и канала, а также труда мастера который отреставрировал.
@pachecoCardososilva
@pachecoCardososilva 2 роки тому
Porque não liga direto o plug de carregamento na própria bateria
@carlosfaria860
@carlosfaria860 Рік тому
Tem que ter um gerenciamento da corrente de carga, e é isso que aquela plaquinha verde faz.
@chemahernandez1696
@chemahernandez1696 2 роки тому
Lo entiendo todo menos la modificación que haces de la PCB. No sé si puedes explicar.
@gear_show
@gear_show 2 роки тому
El PCB tiene 4 conexiones B0 (0V), B1 (4.2V), B2 (8.4V) y B3 (12.6V). Soldé todas las conexiones al paquete de baterías.
@chemahernandez1696
@chemahernandez1696 2 роки тому
@@gear_show ok. Que es lo que haces en la PCB del cargador original?...cortas algunas pistas?
@danielg.vgremio83
@danielg.vgremio83 2 роки тому
D+
@user-nb7tw7rh2l
@user-nb7tw7rh2l 9 місяців тому
How much
@arkadiuszweiss
@arkadiuszweiss 2 роки тому
Super :-)
@gear_show
@gear_show 2 роки тому
Thank you! Cheers!
@user-tt4bp4ml6f
@user-tt4bp4ml6f 2 роки тому
Почему плата защиты не уходила в защиту? Какие то циганские фокусы!
@radtunes7915
@radtunes7915 2 роки тому
Did he leave 1 no cad battery
@radtunes7915
@radtunes7915 2 роки тому
Ni cad
@thuantp
@thuantp 2 роки тому
Máy này sài pin mà mạnh dữ
@Khoa8994
@Khoa8994 2 роки тому
Bên đó ko nhập mạch 3S30A nhỉ, thấy ông này toàn đóng mạch 20A, mạch này tải nặng cái là ngắt liền, hơi kém.
@MeilyFoodie
@MeilyFoodie 2 роки тому
❤️❤️❤️❤️❤️❤️
@gear_show
@gear_show 2 роки тому
❤️❤️❤️❤️❤️❤️
@hasanalitonyali
@hasanalitonyali 2 роки тому
Hello . You didn't show from which end of the battery the wires come from while the battery is in a flat position? that you cut the soldering scene to the batteries in 22 seconds of 4 minutes of the video.. I'm so angry
@zexron97
@zexron97 2 роки тому
Hey
@jorge9132
@jorge9132 6 місяців тому
En el polo negativo no necesita pegatina
@sakthi140oparator
@sakthi140oparator 2 роки тому
Headphones 🎧 user 1:11. ⚡⚡⚡⚡😂😂😂😂😂
@JulianLopez-mk1ez
@JulianLopez-mk1ez 2 роки тому
Skil 14.4v
@user-ms2xh8io2l
@user-ms2xh8io2l 2 роки тому
Разъем для зарядки можно разместить на самой батарее. Тогда зарядка Bosch вообще не нужна. Я так сделал.
1 класс vs 11 класс (рисунок)
00:37
БЕРТ
Переглядів 3,3 млн
Black & Decker 12V Battery and Charger Upgrade Guide
12:13
Gear Show
Переглядів 444 тис.
AMAZING TOOLS YOU SHOULD KNOW ABOUT
16:11
TechZone
Переглядів 72 тис.
Make a Mini Spot Welding Machine for Lithium Batteries a $0 - DIY
13:54
Gianni Pirola Fai Da Te
Переглядів 2,2 млн
Bosch Cordless Drill Repair GSR 12 VE-2
16:24
TI Restoration
Переглядів 5 тис.
Талант От Природы 🤯
0:56
MovieLuvsky
Переглядів 14 млн
Вьетнамские рыбаки убегают от приливной волны
0:11
Короче, новости
Переглядів 7 млн
Бугатти не продадут Тому Крузу авто 😢
0:51