Good point……he does have a Precise lathe for close tolerance work so it doesn’t matter this is just a video not a do the build like this or else!

@@scor440 I can't stop laughing due to your comment 😂👍

"Very well done! Kudos to the young gentleman!"

You always wonder ! What costs More !??

Hello, total cost was around 600-700$ Chuck was 150$, rails around 250$, pulley around 25$ each and steel parts at scrapyard 150$ and a lot of screws... Best option for sure is to buy regular lathe😅 but i have realy small workshop and i dont need too high presition for my projects. Also regular cheapest normal sized lathe in my country is anywhere from 3000 to 5000$😅😅 Also thank you for commeting have an nice day!

@@davidwillard7334 ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran

Estes trilhos, onde consigo comprar? Lojas etc.

Sure, naleti kad god hoces! :)

Hi, purpose of the smaller rail set is for making cone and other stuff under some angle, whole plate with rails rotates around bolt in middle. Also so i can adjust paralelnes of machine. Thank you for watching! 😁

Yeah? What, you want him fabricating linear rails himself?

@user-cg3em4cw4f No, just get quality stuff from Japsn, Korea, or the USA, which actually is built to specification and won't make a mess of his jobs.

@@dnomyarnostaw Ah, I took it as one of those comments complaining that technically the rollers weren't scrap. My bad, definitely true.

Главный параметр любого станка - это ЖЕСТКОСТЬ , а алюминиевые направляющие не могут обеспечить необходимую жесткость ....

And Welder ! / Rod ! Too ??

так этот станок без претензии на высокую точность, а значит и шабрить там смысла нет! рез чистый без биений, без дроблений, а что еще надо от самодельного станка...Там пришабривать бесполезно так как от сварки вся рама винтом и горбатая.

И шпиндельные тоже.

И не говоря о том, что в самоделке нихрена не отшлифовано и не отфрезеровано, никакой проверки на биение и параллельность, нет нормальной продольной и малой продольной подачи, нет ходового и винта и валика, нет нормалтной регулировки скоростей, нет лимбов

Sounds like the factors you are discussing are rigidity and dampening. Yes, this type design would have poor dampening. However it lends itself to be epoxy granite filled which will solve that. Secondly is the cross slide. This setup will have limitations on the depth of cut you can take. You will need to be weary of tool pressure. Other ideas to improve rigidity would be square linear rails, 30-35mm would likely do or even better yet box ways but this requires a way to precision grind and/or scrape.