Im so stoked for my waterproof build. Darwinfpv makes a waterproof stack, camera, vtx, and receiver. And my worry free will be in the mailbox tomorrow. Just to go over all the solder joints to make its 100% waterproof

Right on dude, excited to try it out 🙌🏽

Luv this stuff! I live in Montana. I use this on my snow quads! I fly all winter! No problem! Good stuff! Thanks!

AWESOME...

Thx,super!

got some, cant wait to throw some on man

I put this on my Skystar f722 am32 60a stack, first attempt at waterproofing a kwad and im having a major problem, i doesn't fly well and if i go over 3/4 throttle it starts yaw kicking really bad, is this a know issue, did i put it on too thick? I kinda just smeared it on with the tip of the tube and worked it in the knooks and krannies so it has a good coat cuz this is going to be my night and bad weather drone, is this a known issue? Any info would be much appreciated! Thanks

Can you apply worryfree directly to the rx or is that why you recommend the mg conformal coat? Great video, gonna be throwing some worryfree on my first quad this week

Hi Brandan. Thanks for the vid. I bought some of your worry-free and am about to coat my electronics. One thing that confused me was plugging in the air unit cable. Didn't seem like you needed to plug it in based on how you applied the worry free. I have several plugs in my FC. I am curious if I should coat the worry free over the plug such that I wouldn't be able to unplug it until I remove the worry free. Do you have any suggestions?

Please do a video waterproofing the DJI 03 AU, please 😢

I've ordered a coupla tubes from your website for a non-drone or RC application. It's for 24Vdc LED beacons in an Oil & Gas Marine environment. These beacons don't have water ingress but the glass dome around the LED array condensates and the moisture is dripping down onto the PCB. I'm thinking a couple of coats of spray MG Chemicals 422C over entire PCB and then use FPV Worry Free on the areas where the condensation is most likely to drip onto the PCBs.

nice mate , lets see if i get my quad waterproof :P one question. what about the dji cam or caddax vista part. they not water proof, how do u proof them ?

Amazing stuff! Is the guy in the UK still distributing for you? Love to get a couple tubes.

Hi Thank you for the worry free i have waterproof 2 quads with that stuff. 10x Now i have 5 inch with 03 air unit. As far as i know the 03 is not watterproof as the vista and there is a problem with overheating when it is decased Do you have a solution for waterproofing the 03 air unit without overheating? 10x

so what about the vtx? do you decase vista and put this right on boards, and on a analog vtx just same thing just don't cover button. and what about the camera can you do that as well?

Morning Brandan I received a few worry free fpv all of them are transparent and one is yellowish is it normal ? Thanks

Can you seal a beeper and a gps? Isn't necessary to seal the usb port, camera lens where the screw is and things like that? Thanks!

Do you need to coat the motor as well ? Please answer

Just ordered a couple tubes man! Just want to accident or “oh shit” proof my quad for snow/small wetness in grass etc. thanks!

I have been wanting to do this to my quad so bad since it's snowing and I really was wondering how well the process works I have seen guys submerge their quads in the bath tub lol but I just want to be "worry free" literally lol of snow and maybe just maybe be able to fly during a lite rain 😁👍✌ does it peel off if needed without leaving behind any residue that will make soldering impossible? Just in case you have to throw a new motor on😁

How about the barometer hole? Does the altitude works proper after covering the sensor completely?

Does it conduct heat? If it gets into the usb connector it makes it unusable, no?

when u dip the air unit in water are you meant to wait until it dries to use again? because ive dipped mine in then plugged back in after 5min when still wet and now it won't transmit signal or connect to fav assistant on computer

I just coated my electronics last night and let it sit overnight. I did put a pretty heavy coat on but it's still pretty tacky/stringy similar to hot glue before it's cured. does it fully harden when it's cured?

Do you apply also on the xt60 ? just before the connector ?

what is the ESCs you are using on this drone?

I have an older Armattan badger HD. It has the 30amp chip along all 4 motors and it’s shrink wrapped. Should I just seal in the edges of the heat shrink would that be good enough?

how would I waterproof dji 03 air unit?

i like the stick. proceeds to use his finger lol

I really want to pull the trigger on this product but I need to know how to waterproof the Air Unit. I see the link to the Vista video but what about the Air Unit??????

Hi. any update on the salt water test?

How about a Barometer? I suppose it will stop working after the application of the coat.

bit how well does it protect in a water crash?

What do I do about the open ports in the fc?

Hey brother, is your worry free gonna come back? I need to finish up underneath a stack but its sold out everywhere

What about a 4 in 1 esc.. apply worry free in the gaps of the heat sink.. or I don't ever use individual esc.would you apply it the same .

I’m having a tough time with this. I found this much thicker and goopier than the MG chemical one and it really gums like quickly when i use the wooden tools unless i pour A LOT of silicone. Now i want to remove it all and it’s really difficult. What product can i use to dissolve it away?

can you coat a gopro naked? how about the dji o3?

Can't wait to try it. You have a cold iron ,didn't heat base metal or cooked away all the flux. should be no need to clean up your soldering with snips. Knowing is half the battle.

Hi @Brandan FPV. may i know what to do with the lipo?

How do you waterproof the motors? Don't they short?

where can i buy them

Can you ship to indonesia??

Can you just burn it off with a soldering iron if you need to make repairs? :)))

Bought this from supplier in india. it seems alot watery and not thick When I tried to apply it it would drop down from the other side. Did I buy an imitation of the coating or it is how it is?

Might want to add how viscous is the actual fluid.

Why mention conformal coat for the rx instead of using ur worry free to cover the rx like u did the fc. Always thought/thinking about conformal / silicon to water proof my builds. But thinking about if u have to get to area's needing repair thst cover in silicone. What u remove the coating with to get threw say if you need to repair a wire on a pad on fc etc. An like xt60,or analog cams wire harness that would be sealed up also right.like I said I really been think to do it for long time. But conformal or silicone or both I don't know.never really found full in depth video or articles that cover all in one.most I find are like this video.good content but so much left out for someone who never used conformal or silicone should both be used etc. An like all the little connections /headers, cam casing should they be opened an add some silicone to seal an Things like thst keep me from doing it cause it's never full covered in one article or video. I know this one was a promo short video but really not much help beside having more questions lol.hope u understand whst im meaning.

Hi, You forgot to waterproof the motors !!

Where is the difference to conformal coating?

Hey Bro Happy FPV gave me some worry free would you send me a sticker or 2 thanks bro

The only downside is i only bought 2 lmmfao

Why not just laminate a drone? Or stick a plastic wrap with heat