He, he...same thought here. All that lathe work and then BAM! He bashes a bolt into the damned thing.

There are easier ways to make a socket.

Thanks brother ♥️

Terimakasih saudaraku ♥️

Thanks brother Matty's ♥️

G'day Matty, fancy seeing you here mate lol, did this fella move shops? I haven't watched him in a little while

@@RalfyCustoms Gday, Yanto has started his own workshop, he’s going to do alright to mate,

Thanks Frank ♥️

Terimakasih saudaraku ♥️ 🇲🇽🇲🇽

🇨🇱🇨🇱 Hector ❤️

Terimakasih kangmas Dadier ♥️😍

Thanks brother 🇦🇷🇦🇷🇦🇷

Jose Maciel Zamudio ♥️ 🇺🇾🇺🇾🇺🇾

Terimakasih saudaraku ♥️

Thanks brother Okoro 🇳🇬🇳🇬

Thanks brother Jimenez ❤️

Do you live in Australia now?

@@Kenan_KARA Yes I do just be careful using powerful machines GOOD LUCK and be alert . Cheers

@@kevinklei3005 Thank you.Greetings from Antalia

There's a gory video on the Internet of a Russian guy killed by a lathe. His coat sleeve got caught and his whole body got pulled in and shredded. Absolutely gruesome.

@@davidkim4083 I saw the video...horrible death for the poor guy. It reminded me of an incident years ago in school. A guy had a scarf around his neck while operating a lathe. He knew better and everyone was clearly instructed about the safety and what NOT to do. Anyway, the damned thing got caught in the spindle while it very fortunately ran low RPM. The guy next to the idiot was aware of the situation and immediately hammered the emergency stop. The idiot returned to school after a few days off with a very clear strangulation mark around his neck. It was a while before he got near a lathe again and he was more than lucky nothing bad happened to him. Machinery in a pro workshop can kill careless operators!

Terimakasih Denis ❤️

Iya kang.. terimakasih kang David..ini karena dukungan dari jenengan

Thanks brother ❤️

Thanks brother Trapper

Thanks brother Adrian ♥️

Thanks brother Asturias ♥️

Sidney Ferreira ❤️

Aamiin.. Alhamdulillah ♥️

Saya menggunakan mesin pak

@@Yantoo Anda menggunakan pompa air submersible tipe pena

Más bien pregunta, como hacen el huevo cuadrado

Как-то не припомню про дефицит инструментов особенно при совдепии, я досих пор пользуюсь теми запасами, взял как-то набор метчиков , и плашек всех размеров штук 150 качество не Китай работает досих пор

Мы так и делали . Только ещё отбивали по окружности на шестиграннике ,что б плотней и чётче было.

Thanks brother Stewart ❤️

Thanks brother ♥️ AR

Thanks brothers David

Thanks brother Shahzad

does not look like he is in a position to walk to the corner hardware store

@@georgeh9967 You severely underestimate the availability of tools (possibly tenth-hand used, but nonetheless there to be had) even in low-tech looking places. Ca Lem has a good video on this - you just shop at the tool flea market instead of a hardware store, and you buy what you can find, not necessarily what you came for. But make no mistake, in a place where a socket wrench truly is unobtanium, there are no functioning lathes.

@@AttilaAsztalos not in a position to walk to the corner hardware store.means. he is far from store /town. maybe rural. it is a saying. and in no way has or means anything about the tools he may have. he did use a lathe and various tools. and in fact has more than i have.

Thanks brother ♥️

Terimakasih Horaldo ❤️

Terimakasih saudaraku ❤️ ♥️

Terimakasih pak Patma

only a spark eroder I think

In mass production they are broached in with a single punch, heat treated and chrome plated.