Great build and very innovative use of a drill bit with spiral flutes. There have been a lot of makers with straight flutes, but I like the spiral, and old bits are fairly easy to come by. Thanks and cheers! Someone should forward this vid to homemade tools.

Красавчик ! Чистюля !! Приятно , когда все почти идеально !!! Успехов ❤ , за наждачку и образив минус😢

With no doubt, the very best tap. I know because I made some myself in desperation, on weekends where I need it one and every shop were shut, but the cheapest tap would do the job in good hands.

This video really makes me appreciate just being able to buy one.

Absolute HOCHACHTUNG! Das war der Beweis, daß es noch echte Handwerker gibt! 🎉

You should note that drill diameter are actually slightly smaller than stated size and tap diameters are slightly larger, so take care for a screw to fit the tapped hole!

Great job my friend! You left out only one thing, tempering. it is very important that the tool is not brittle, because one wrong move can break the teeth. in the case of tool steels, they undergo multi-step hardening, which makes the material very resistant. great job by the way!

Pensa num cara treinado! Belo trabalho! Valeu muito obrigado!!!

Do I understand correctly that first you release the metal (remove the quench), and then re-quench after processing? Cool work, but for those who have a welding machine or a heating furnace.

Damn fine work! That was some quality stuff. It's also nice to see someone that actually does things correctly and properly when it comes to machining and metal working. Nowadays I see so many people on the interweb UKpostss that cut corners, force things, and sometimes simply just don't know what they are doing. Then they make videos and pass those bad habits on to others 😢. I also appreciate that you know how to correctly grind your own lathe bits which is something that all machinist should at least know how to do whether they use indexable bits or not. That is definitely a dying art. You are quite impressive my good sir, keep up the good work! 👍👏😊

Instead of the Three Jaw Chuck, you should use an ER32 Collet for better grip and concentricity.

Very well done. I keep in mind your way to sharpen a tap drill.

Witaj Fachmanie młody i najwyższy Szacunek od starego zawodowca, super robota!

A handmade tool is always a reason to be proud. Congratulations and best regards 😀.

Magnificent work.I need to make an m20 nut. I'm going to take advantage of the idea and do it with a 22 inch drill that I have in the workshop ... ( Not inches 22 m/m diameter )

19:26 why this way? Use drill machine 18:25 for perfect coaxial hole.

Спасибо. Идея которая лежит на поверхности. Можно изготовить метчик с направляющей. Его иногда так не хватает.

Superb skills and hat off to someone’s that really deserve It.

Good video. I will try this method some time. Cheers Rob

Nam știut ca din burghiu poate sa facă asa ceva tarod bravo meseriasule

отличный мастер молодец

Bardzo dobra robota!!!

Un artista!. Si señor

Ficou muito bom!! Parabéns

Excelente trabalho e muito conhecimento parabéns

Compla ali na China, balatinho né?😂 Excellent job, congrats.👍👍

Most TiN-coated drills are not real M2 or M3 HSS, so your tap is probably alloy. HSS is air-hardening, so it's very difficult to anneal.

Very good idea, and better job ... i only ask how much oxygen was used, and how much would be instead cost a commercial tap ... ( of course not to deal with taps that are really "hard to find" on the market ... ). Note : a test with a blind bore would be much more relevant, as spiral taps are expecially designed for that type of holes ... Thank you very much in any case for your usefull lesson, i really appreciated both the heat treatments of common drills ...

Parabéns pelo trabalho e pela organização e limpeza durante o trabalho.

Bom trabalho que fez com a broca quebrada, parabéns

Just a quick question. Doesnt the reheating blunt the cutting edge of the tap?

Good work. We shared this video on our homemade tools forum this week 😎

Great job really! Only time I got was holding on to the part by hand during the drilling process. 🎉

Can an Acme hand thread tap be made in the same way? Would any modifications to this protocol be needed?

Now if you only had a twist drill that was left hand You could have the chips fall down Well done And I love the fact no crappy music Thanks

Молодец! Работа на высоком уровне. Продолжайте повышать свои навыки.

La pregunta es. Quien tornio las parte del primer torno creado ???

OLÁ. Gostei de ver. Acredito que o primeiro aquecimento foi para "temperar" a peça. A sugestão é a de um esfriamento mais lento colocando-a no mesmo recipiente porém envolta de grossa camada de "Carvão MINERAL". No final, a forma como foi feita a "CIMENTAÇÃO" é muito provável que a peça se torne 'QUEBRADIÇA". ABRAÇOS... Roberto Udo Krapf

Buen trabajo aunque pensaba, sí, en el costo beneficio. Pero es un trabajo artesanal a costa de ingenio , paciencia y habilidad. Es una satisfacción para el que lo hace. Vaya mis felicitaciones para Master y gracias por compartir conocimientos.

Muito bom!

Adamın dibisin kardeşim 🎉❤

Genius!! The possibilites are endless!

The old way of screw cutting took skill and a sharp brain, it's scandalous how the salary of a toolmaker or machinest was so average for such a skilled job. Dying breed nowadays

4:03 which insert are you using for turning???

Muito bom excelente parabéns

Hello, have a good time, don't be tired, thank you for your good video, it was very good

Exelente me gusto la idea grasias por compartir

Bonjour,quel beau travail. Très bien filmé. Mes respects 👍👍👍😉

Why you applied heat before machining the bit??

Atelier propre, machines outil propre et enfin un travail effectué dans les règles de l’art. Je respecte et admire les personnes comme vous qui exécute des travaux frisant l’excellence, je remercie ceux qui vous ont transmis leur savoir et je ne doute pas une seconde que à votre tour un jour vous le transmettez à votre tour…… Cordialement

Jak ja dawno nie ostrzyłem noża oprócz przecinaków do plastiku

Все прекрасно. Мастер рукастый, но вопрос зачем? Метчик можно купить, а не тратить на это весь день

Sangat menakjubkan kawan. Hand trhead yang mantap

Gran Bel Lavoro da professionista e con stile. Complimenti sei Bravissimo.

Super jest to pomysł pozdrawiam serdecznie 👍👍👍👍🏻

I'm already subscribe from some previous ridiculous video I watched of yours. Love the innovations!

Very Very good

Very Helpful and Informative video 👍✌️❤

Complimenti!!! bellissimo e perfetto lavoro👍👋 Un saluto da Roma

How did you know how fast you need to rotate the piece and how fast to move the cutter in order to make the thread`?

Well done that man.

I like what you did fella, but taps are not that expensive. But you did prove one can make it happen. Nice work Master Mind.

very good job,thx!

Great job 👍

Materiał zachartowany powinien być odpuszczony czyli jego twardość trochę się zmniejszy ale nie pęknie gdy przez nie uwagę spadnie, czy gwintowanie pójdzie trochę bokiem, lub inne sytłacje. Prosty sposób na chartowanie byłby taki jak zrobiłeś na początku. Grzanie jeśli możliwe całego elementu (najlepiej przez 1h) lub chociaż 30minut w szamot (cegły piecowe) i potem zachartować w całośći ale zostawić do czasu aż ostygnie w całośći. (Może w wodzie ale z dodatkiem soli (są osoby które dodają też sól do oleju ale efekt mi nie jest znany ??). Następnie czysty gwintownik wkładamy do piekarnika na 1h z tem 100⁰C (tu bywa różnie od metalu i odpuszczanie może być nawet w tem 250⁰C-ale jak dla mnie temperatura bezpieczna jest tem max 150⁰C. Tak naprawdę wszystko zależy od stali.) Czasami trzeba jeszcze raz włożyć do piekarnika po całkowitym ostygnięciu na kolejną 1h-100⁰C. Dobrym wyznacznikiem twardośći są koncówki (igły,szpilki wewnętrzne wtryskiwacza) i próba nabicia na główce małego punktu. Przy normalnym uderzeniu, głebokość punktu, lub uszkodzenie szpilki wew. wtrysku. (Sam czubek jest utwardzony . I nie polecałbym mocno bić młotkiem ,czy z boku gwintownika czy innego utwardzonego elementu). Na wpływ twardośći materiału ma też wpływ gaz jakim grzejemy materiał. ACETYLEN -powoduje że powierzchnia elementu staje się bardziej twarda !!!!!!!. Pozdrawiam

Super podoba mi się

круто , но уж очень заморочено . 👍

Very good idea.

موبدع وعمل جيد جداً

super good work !!!

Schöne Arbeit, aber lohnt sich der Aufwand.

Excelente trabalho

Bro i appreciate how clean you work ! Great job!

Shouldn't you grind a relief at the back of the flute thread?

Nice work

muy bien para fabricar machos de roscas poco comunes parece una idea genial, para roscas comunes no merece mucho la pena acabo de compara un M11x1 por 4 euros( igual solo hace una rosca pero va a cumplir)

Bellissimo lavoro

When you just have many cool machines.))))

That is my kind of recycling!!

Bravo Bravo Türkiye İzmir selamlar ve abonelik 🎉

Great 👍👍👍

Ещё бы научился затыловку делать!

The card is great, but the quality of your camera😢😢😢

Nice 👍👍🤝 Dear friend so amazing🌹☺

Slick! Great video thumbs up.

Very nice work

Excelente trabajo🙏🤗

Красавчик

If you tell me to like, I WONT!

там видны сколы после использования один раз.

How much is the price? I like it

Great video just a little note when lighting a gas tourch you should use a sparker instead of a lighter as the lighter fluid can have a blow back and cause the lighter to blow up in your hand

Good oye Good

Good work👍

10:54 First time i see a SHCT… Socket-Head Cap Tap

کارت درسته رفیق

Nice job,👍👍👍👍👍👍👍👍

Nice work piece

کار جالبی بود👌👌

I enjoyed a lot and thanks