Thank you very much my dear friend🙏🙏💐

🙏💐

Glad you enjoyed it🙏💐

Thanks ✌️

🙏🙏🙏🙏👍👍💐

thanks for watching🙏🙏👍

Glad you enjoyed it!🙏

Wow, thank you🙏💐

Thanks🙏💐

Hard steel my friend

Obrigado meu bom amigo e fico feliz que tenha gostado

Thanks a lot 😊

In fact, you can get the answer to your questions by looking carefully at the end result of the work and the smooth and shiny surface of the thread.

Thanks for watching🙏🙏🙏🙏❤️❤️

Thank you very much🙏🙏👍💐

Sí, mi buen amigo, y te lo agradezco mucho.🙏💐

Y tocante al dado si fuera usted tan amble de compartirme que acero ocupo se lo agradecería

Hello my dear friend Yes, correct This is to reduce the hardness of the steel so that it does not become brittle In other words, relieved

Ok, thanks again. Spiros

It's called 'tempering', reheating at a lesser temperature and let it cool in air. Was a student of metal work 53 years ago.

​@@fredericknshemereirwe8440смотря какая сталь, с Р9, Р18, Р6М5 не прокатит. Там 3раза нагрев 900градусов с остыванием на воздухе, заводская термообработка в бариевой камере, как, я не знаю. Почему метчики делают из Р6М5, а плашки из 9ХС?посмотри сам....

🙏🙏🙏🙏👍❤️

Obrigado meu bom amigo e estou feliz que você gostou do resultado

🙏🙏🙏💐

selam kardeşim Üzgünüm ama ne demek istediğini anlamadım

@@Mastermind- Abi benim whatsap nomerem kanalimda bekliyirem

Coming soon!

In fact, the position of the four holes on it automatically provides relief, my friend

steel

​@@Mastermind-марка стали? Завод - 9ХС,ты из какой?

What do you mean?

🙏🙏🙏👍❤️🌹

Grazie mio buon amico e sono molto felice che ti sia piaciuto👍💐

For hardened

No , it's oil

Or GRADDER BLADE CUTTER Edge steels .. is vvvv good steel . I made an axe from some . Heated it up red n droped it in sump oil . Vv hard sharp cutnn edge 💥👌👌👌👌👌👌👌

Röhm is the best 👌 👍

In fact, the retainer is not hardened and there is no need to harden it

For standard sizes and threads, you are absolutely correct. You may never need a non standard threading. Or a tool of non standard configuration for use in a confined space. Some tools such as bottoming taps can be hard to source and expensive though I have made them from normal standard taps. Anyway I thought it was a good vid though I admit I did skip past some places.

Go smoke some cones .💥🤑

For a standard size Die this is true, but many times you are requiring a multi start Die of odd dia and TPI, then this technique is the only solution, and the $40 Die holder is probably a chinese one made from Mazac. Chris B.

Because high quality Taps and Dies aren't just a few dollars. This guy is making ones of better quality than the good majority you'll find in Hardware Stores.

And for content too😊😊

Exactly🙏👍

This work was done, my friend, and finally the result shows this well

@@Mastermind- It's okay if you only wish to make UKposts videos and never improve your skills, just don't call yourself a "Master Mind' and lead the viewers astray.

I thought the same! I always screwcut the thread, then bore the 4 holes after, it does not damage the threads at all, and the thought of those 4 plugs turning and locking up gives me the sweats. Chris B.

Thank you so much 🙏👍