I converted the engine from 1 cylinder to crossplane 3 cylinder SOHC
КОМЕНТАРІ: 604
@cathy57229 місяців тому
Le Dan is a motivated artistic engineer with a photographic memory. He can see in his mind what he wants and then builds it by himself in spartan conditions. Who else does exactly that?
@Motoreger9 місяців тому
Allen Millyard.
@YyouTTubeE9 місяців тому
Spartan condition
@enjoyaja4359 місяців тому
88
@bagassaputra87169 місяців тому
Nagalima builder and most of the south east asean builders do as he does
@changi87549 місяців тому
Once in a blue moon born
@kg_canuck8 місяців тому
What you do really reminds me of Allen Millyard's builds. Amazing engine mashups with extremely basic tools, although you seem to be doing similar work with even more basic tools. Always impressive to see a truly creative, driven, engineering mind at work make amazing projects without a commercial grade workshop/equipment.
@songsurelookingfor84159 місяців тому
Can we make a single cylinder into dual with less complications like merging their heads or even their camshafts. I meant to say that both heads have their own separate timing chain. Please try to make a video on such type of engine
@aserta9 місяців тому
If you bake the aluminium inside some super fine, almost dust like sand, you'll be able to remove quite a bit of the oil that's causing all that porosity. Not easy to achieve, but it does work. Also, you should clean all the surfaces you weld on with a stainless steel brush that's only for aluminium, and nothing else. Your welding is good, but the castings make it difficult.
@creatornavi26159 місяців тому
Here comes the expert
@alejandrosalzmann65389 місяців тому
S
@alejandrosalzmann65389 місяців тому
Q
@abcunil9 місяців тому
Can u do this broh?
@firdauschanel9 місяців тому
P
@meandthecat40259 місяців тому
I truly admire the craftsmanship and creativity. Comparing your workshop to some of here in Europe, you get a lot more done with a fraction of the tools, bravo. I have some crazy ideas myself too, I was planning to build a 600cc or 1000cc supersport/superbike, and making it a one cylinder, but with the same horsepower ratio. A 250cc engine with 40hp is nuts, if we take moderate superbike spec. Maybe a future project for you aswell, would love to see how you build more.
@maspintarjualan54059 місяців тому
torque monster, for sure but many prefer to build a superbike using multi-cylinder configuration, because the secondary balance and many other things will cap the rpm
@kristiansomogyi7446 місяців тому
You can't get the same power with just 1 cylinder.
@jiboy85499 місяців тому
Can't wait for this engine's first start up.. you're a true wizard le dan. Amazing skills and craftsmanship. I love watching your videos. Keep it up Wizard
@Immortalrounin9 місяців тому
I love all of the videos you make ❤ still hoping for the v8😎
@gadji05269 місяців тому
+++++++
@weshipitjamaica43549 місяців тому
Yes we wait for the v8
@futuristicart80009 місяців тому
Same here thats why I ask him to merge two R1 RR engines together for my project I have in mind
@Immortalrounin9 місяців тому
@@weshipitjamaica4354 he made a 4 cylinder that was like 60% to a v8 not too long ago
@Immortalrounin9 місяців тому
@futuristicart8000 they did that but with the hayabusa. (Not this channel)
@saturatedtv51389 місяців тому
this is what i am waiting for..a crossplane setup..good job Le Dan..salute !!!
@peterp.13119 місяців тому
Again and again a fantastic processing..Top..greetings from Germany
@diyathomevn5 місяців тому
Great idea It's impressive to see a truly creative, motivated engineer at work, creating great designs without the need for commercial grade plant/equipment. It can be said that you are a saint
@fauscsk_90999 місяців тому
Seeing Le Dan's reflection during sand blasting was like some sort of vague surreal meme, love the content
@nurulfadilah80799 місяців тому
Sampean cerdas....aku ndelok rangkaian mesin wae mumet...mumet ....koyo ndelok Iwak neng jero sumur
@user-np4by7jj8l9 місяців тому
Молодец парень,золотые руки.
@user-pp9gw2ns3b9 місяців тому
Брат ты лучший !!!!!! Это талант мастерство знания в купе !!!!! Удачи тебе
@user-ed5mm7zf9o6 місяців тому
Класс !!! Отличная работа. Успехов в творчестве .
@kkpatil849 місяців тому
Your skills are amazing,love your videos, one suggestion please mention in written text on video, every important operations, example if you're creating a port for spark plug, or on what engine part , cylinder head or crank case or cylinder itself, what operation your doing and for what, that will be so informative and helpful .
@kalybnielsen41839 місяців тому
I need a Honda 110 motor converted to a two stroke. I'm jealous at the parts he has available to him, great videos, excellent abilities
@miguelsampaio61999 місяців тому
Love your experience you are a genious. Like to see you making a liquid piston engine or a free valve engine.
@ASMReverything287 місяців тому
Bro's not too far away from making a V8 Scooter engine! 😂 You make impossible build look like a childs play, awesome craftsmanship. 👏👏👏
@h-j.k.89718 місяців тому
Tremendous work, could watch all day.
@happyowner93479 місяців тому
Этот парень когда-нибудь устает? Великолепная работа!!!!!💥
@nickmassey91049 місяців тому
Awesome build as usual .Great skills
@nigelbutler94889 місяців тому
Another great video. Watched it twice. Have you ever considered the honda sonic nova 125 twin cam engine as a donor for a V or crossplane build?
@davidforsman59738 місяців тому
Can't wait to hear this engine running 🙌
@justinpouplier97827 місяців тому
Hi, thanks for the video. I have some questions, what's the purpose of that plate and the cut below it that u do between 11:00 and 13:20 of the video? And also, why did u feel the need to change the spark plug location from the original one? Thank you for the answer.
@mustafamansuria43577 місяців тому
انته فنان في هندسه المحركات تستاهل المليون مشترك ❤ متابعك من العراق❤
@tiredironrepair8 місяців тому
Would you do an inline 4 cylinder with altered cam timing build? So it fires cylinders 1 and 4 and then 2 and 3 at the same time essentially making it a 2 cylinder with huge displacement? Originally I thought of the idea for a small block V-8 to run like a 5.7 liter 4 cylinder.
@davezu098 місяців тому
Awesome work, I would like to know what engines are you using for those proyects.
@tehnoelektronikloznica711910 днів тому
Potrebno je mnogo znanja, veštine, alata, novca, vremena i ljubavi prema poslu, da bi se uopšte odlučio da započneš ovako veliki posao, a kamoli da ga realizuješ! B R A V O!
@rraji8669 місяців тому
finally, im a bit worried with your hiatus, but then BAM.. new engine made precisely.. Well done Prof,..
@paulthomas52584 місяці тому
That crankshaft at the start of the video is fantastic work
@yusufabdrahman5929 місяців тому
So good ii boss 👍👍😊😊 buat part 2 k tunggu video baru k 👍👍
@Tommysmess9 місяців тому
I love the build! Cant wait to see you make a inline 5 or 6 👍
@mechniack8 місяців тому
Have you noticed that he reuses the 125 gearbox in all his build, and guess why ! And do you think those gearbox can handle an inline 6 get a grip on things
@Tommysmess8 місяців тому
@mechniack how about it was just a idea. He builds all the other types of motors, he has also used 300cc engines so idk what your talking about, yes these are 125cc engines, I bet it would be just fine with a Inline 5 or 6,
@BINTANGAutoworks9 місяців тому
We waiting next part.....great video brother....greetings from Indonesian mechanic
@user-rx3rb9pg5z9 місяців тому
released in right time for tea! cool as always bruh! 😉👍
@steveshoemaker63479 місяців тому
Le Dan you are the SMARTEST GUY ON youtube....l just love watching❣your AMAZING VIDEOS and i am in my 80's....... Thanks so very much and waiting on part 2 of this engine 👍 Shoe🇺🇸
@danilocabral52309 місяців тому
É inteligência demais para uma só pessoa ! 😁 parabéns 👏🏼👏🏼 🇧🇷
@mikenzo7225 місяців тому
That's why I love watching your videos. And thank you for your sharing this idea.😊
@vanivanov9 місяців тому
Great job so far.. Please just don't drive camshaft by same chain what was used in donor engines. Use at least 2 next to each other (if you have room)or use something wider from bigger engine.
@voodoochild8008 місяців тому
I like your work! 👍 could you tell me what press fit you use for your crankshafts, 0.05mm? 0.03mm? Thanks
@MotoEnz9 місяців тому
Thank you for making our request happen. You are awesome Great engineering 💪🤘
@hoadoan37109 місяців тому
Việt Nam mk nhiều người giỏi quá , hóng ngày nó thành cái xe hoàn chỉnh❤
@user-zi5cd6xi4f6 місяців тому
Le Dan, I challenge you to make a 2-stroke 4-cylinder in-line engine using 4 80cc motorized bicycle engines
@jonathanulco83919 місяців тому
Admiro mucho tu trabajo eres genial en lo que ases amigo Saludos desde ECUADOR
@locpham22179 місяців тому
ủng hộ những sáng tạo mới của a. chúc a luôn thành công trong những dự định mới
@quyieu87159 місяців тому
Não bộ của ah giờ đã đạt một tầm cao mới ah giỏi hơn bất kì ai. Chúc ah luôn thành công trong công việc.
@khatrantrong19539 місяців тому
Rất tài giỏi , rất tuyệt vời . Ngưỡng mộ em !
@ongnguyenson31139 місяців тому
quá đỉnh. ra thêm bản 4 xi lanh như r1 thì quá phê
@karlalton31709 місяців тому
Chào mừng Dan trở lại, và công việc tuyệt vời cho đến nay 😁😁🤘🤘
@samhendra74609 місяців тому
From all of your videos, especially 4 stroke, i just wondering about the oil pump, did u change it or use stock?
@renz10139 місяців тому
Most youtubers when they do stuff like this normally have a 21 part series that'd have 20minute long videos with a lot of intelectual talk and planning. Whilst Le Dan here just decided to film cut and post and see what comes out of it. Just impressive man.
@DanWoodTomwoodson5 місяців тому
Yes. Completely. We'll almost completely. now that I know what he makes is worth my time I actually would like to know more about his thought process.
@renz10135 місяців тому
@@DanWoodTomwoodson Maybe he has a second channel but from the looks of it there might be a language barrier.
@takeshifukuhara85789 місяців тому
wonderful. The quality is improving each time.
@muhammadalfin28919 місяців тому
Mekanik luar biasa Indonesia hadir😅❤
@rgreerjr9 місяців тому
this channel will never cease to amaze me.
@poprawa8 місяців тому
That's mental, thanks for the video C:
@Muhammad_Aditya3269 місяців тому
I thought you stopped making videos, it turns out that you are innovating again. It was so amazing, I waited months waiting.....😊😊
@thanhhaihuynh16299 місяців тому
Không có bản vẽ gì hết mà làm hay thật sự , nhìu người tài giỏi ghê 👍👍👍👍👍
@levannamcuong83299 місяців тому
Chúc mừng bạn đã chế 1 chiếc ex lên 3 máy Bạn làm bên máy móc tôi chỉ mong bạn làm cẩn thận và an toàn Chúc mừng bạn nhé
@lukmanprojayan31887 місяців тому
Ini yg aku tunggu2 mesin crossplane hand Made amazing
@vvmrace6 місяців тому
Awesome build , like all your other projects.
@lunamiracle9 місяців тому
Wow 135cc jadi 400cc, cannot wait for next videos👍 mantapp
@grobischmiede93019 місяців тому
Greetings from Germany I love to see your Videos in my garage and drink beer 😅
@johnurielantigua99209 місяців тому
Im dying for the next part which is the testing, keep it up man, God bless
@Bayuhutamamotor9 місяців тому
Mantap tidak ada bosannya selalu memberikan wawasan sehat selalu dan sukses selalu bang 🙏
@IamNusantara9 місяців тому
Can't wait for the end.. 🔥🔥🔥 But, Still wait for the 1 cylinder dohc suzuki satria/raider/belang engine into 3 cylinder.. 🤘🤘🤘 #salamFromIndonesia
@alejandracadicamo30859 місяців тому
la verdad siempre me sorprendes con tus videos,te felicito por tus trabajos y habilidades en la mecanica..saludos desde argentina
@fenrir47399 місяців тому
Increible le, un saludo desde uruguay yo y mis amigos admiramos tus trabajos🎉
@jayburrough43089 місяців тому
This guy knows these engines in side out just think what he could build with a shop full of the right tools
@zaitmorkam67929 місяців тому
Very profesional...milling mechine...respect your job...
@Rdc-jz4gm9 місяців тому
Gift me one of your best works sir, you are my role model, I am very proud of your work
@nguyenhuequang90759 місяців тому
chờ kết quả hoàn chỉnh và ráp lên xe như thế nào? Chúc bạn mau thành công
@AqlaZenanMauli-oe6no6 місяців тому
it's a great video brother, better put the watermark on your center from beginning until end of video, literally on center not the bottom of your video, because i saw many videos from your channel being reupload on tiktok without putting credits of your channel
@phunguyenmr5928 місяців тому
hóng e làm cục máy winner 2 máy 😊😊, chúc e nhiều sức khoẻ nhé
@lean17279 місяців тому
Professional Machinist 🙌
@hancbr40069 місяців тому
Bữa nao anh làm 4 si lạnh nữa nha em khoái nghe tiếng 4 si lạnh qua😊
@vladim4739 місяців тому
Красивая работа!👍сделай такой двигатель из моторов от мотоблока
@mikepertle35826 місяців тому
I would like to pledge le Dan to my team when the world ends. Having a guy like this will be invaluable
@khang.ngtr4875 місяців тому
this is beyond impressive!
@Iowa5999 місяців тому
Now you should make it into a 2-stroke, that would solve the problems with compression ratio & camshaft drive chain.
@ngocphuphan51497 місяців тому
Người Việt Nam! Tự hào về anh
@imjustkidding79089 місяців тому
Looks like straight from the factory 🏭
@user-cl9nb7gt6o9 місяців тому
สุดยอดอีกแล้ว เยี่ยมมาก
@alur.779 місяців тому
Ditunggu proses selanjutnya hingga selesai . saya menanti pembuatan mesin 3 silindernya ❤
@yodamnhsaputrano80429 місяців тому
AMAZING JOB my friend. Incredibly amazing.
@user-eu8fl8xu8g8 місяців тому
Part 2 ny. Le dan emang master costom engine! Salam dari indonesia
@Gabriel-rn1si9 місяців тому
Cara eu fico ansioso para assistir um vídeo seu. Você é um artesão e um mecânico excelente!
@hamzahaji50679 місяців тому
Last time i comment about crossplane, and now you made it happen🔥👍
@ducgiangtran87399 місяців тому
Đỉnh quá idol ơi ❤❤❤
@Guds7778 місяців тому
If you want a vibraitor, then you build a crossplane. I own Yamaha R1, that has the infamous crossplane, and it has vibraition...
@hungduong26008 місяців тому
Theo dõi và xem anh làm từ những video đầu tiên. Giờ đọc cmt thấy a ko nhận làm thấy buồn quá 😢
@minn58989 місяців тому
Anh giỏi quá, ngưỡng mộ ghê ❤
@maspintarjualan54059 місяців тому
so the spark plug position is located between two ex-valves, interesting definitely would like to see this baby MT-9 running
@faiqsports64389 місяців тому
why not just make a 4 cylinder Crossplane? we are waiting for the next, cheers ❤
@minhaibui9 місяців тому
cho em qua làm R&D bên Vin hay Honda hoặc 1 cty về xe máy có tiếng chắc em phát triển nghề của em lắm. Thân
@personablade36699 місяців тому
lên 3 xilanh máy winner đi bro , chế luôn thành con xe kiểu mới 😅
@RitaElaineHeltonBarker-uz4sz4 місяці тому
I would very much like to see a Three Cylinder Honda Trail 125 to become a Honda Trail 375
@adisuprapto40259 місяців тому
một cái ấm áp từ một người đăng ký Indonesia, tinh thần làm việc👍👍🙏🙏
@AnibalMotosePasseios9 місяців тому
Ai esta um video que me faz continuar pagando o UKposts premium. Obrigado, @leDan pela aula de construção de motores.
@azindependence949 місяців тому
Very talented! Greeting from malaysia 🇲🇾
@imamkeceng83509 місяців тому
Hell yeah🔥🔥🔥 Le dan come back again!!! We from indonesian fans❤❤