I love that your fan has an xt60 connector

"when your done completing the joint, just dab a little bit more" J. Bardwell @8:17

I've been using this stuff for years. All of my builds electronics get coated. I've flown in downpours, crashed into wet grass, puddles, snow and once in a pool. Never had any failures due to water damage. I take a heat gun to it to loosen the cap when it gets stuck to the bottle.

I'd like to see a video where you test out "Lipo fire safe bags". I have a tough time believing any are good enough to be worth spending money on them.

And you should say..." I learned something today"

Got to admire a guy that admits he's faults... great video

Distilled water flush is great advice. Years ago, I flew a marine life observation drone that landed and floated on the ocean. It required a distilled water flush after each flight followed by a WD-40 spray rinse of the motors. Flushing with (distilled) water is counterintuitive but apparently worked for this specific project.

yeasterday I dumped my TP3 into a water bucket. I pluged out the battery before removing it from the water. It survived 100% Thank you Joshua for your tips 11:06

Worth to mention, that motors don't need to be covered with coating because of magnetic nature of motion. Brushless motors are waterproofed by design.

Was waiting for a video on this topic! Thanks Joshua.

I just want to say that this channel is truly so fantastic.

Thanks for this video - I know what I will be doing for the West Coast winters.!

thank you for this. I was expecting it as an out take of the mobeetle review. but you went a step further and made a great video about water resistance prep. I have recently started to coat all my quads. carefully

Thank you for the complete guide for conformal coating. When you mention products like FPV Worry Free, it looks like people can dump their quads into the water and the quad can fly away without any issue, maybe a part 2 with this kind of product would be useful for us :)

Josh is the coolest nerd I know, Have helped me in my FPV journey beyond saying.

Good to learn that conformal coating will work when you dump it in water! I conformal coat most of my whoops and quads only landed in wet grass so far and they all still work.

conformal coating is essential where i live, i like to use the 422C conformal coating as u can ensure its covered using a uv light.

Definitely costing my drones... Thx for another great clip 🇿🇦

Thanks! I live most of my summer on a boat and love to fly FPV from my boat but I’m constantly worried about the water. GREAT VID!! Would love to see you actually fly it into the pool and then fly it after it dries. Prior Navy Aviation Electronics Technician here, so I understand the concept of conformal coating for sure… Anyway… Thanks for your awesome service Sir. I’ve watched countless hours, so it’s about time I kick in a little tip for everything you’ve taught me.

We had spray bottles at work but instead of spraying we put a cotton swab (with hollow plastic shaft) in the nozzle and they you could use it to spread it more accurately.

Somehow managed to leave my taranis out pver night and it rained, had pretty much killed it, opened it up and sat it on a dehumidifier for a couple days and its fine now! Also, used to dry out something else the same way, to speed up the process! Would definitely recommend a dehumidifier if you need to dry stuff out!

The shark shot was pure awesome. 🦈 Comic cinematic quality, Bardwell! ^^

your the best. it was fun contest, and i learned somethings

I had a 16 x 16 iflight pinned stack in a small 2.5 inch that I recently retrieved from a tall tree after being stuck for over 2 years. Surprisingly everything still works fine. Except for the one motor bell that showed my bb gun aim was dead on the money at least once! It had been 90 degrees and better with no rain for a few days prior to the rescue. I have just put the stack in a Darwin fpv tiny ape frame and flown for a few weeks now with no issues at all.

Wet grass took out 1 of my esc's on my 4 in 1 about a week and a half ago. New speedybee setup is performing nicely though!

I learned something !

I use Urethan based conformal coating, it is more pliable and has better heat resistance.

I personally use nail polish top coat. After two crash in to sea quad still working well

I conformal coat good the ones that go in the snow. Other ill lightly hit motor pads & battery pad from outside sometimes after actual testing that it's working good

Electronics technician in a previous carrier. Never heard of the unplug it before removing it from the water theory. But I suppose I can maybe kinda see some validity to it. Definitely recommend removing the battery ASAP! Also isopropyl alcohol is one of the best tools for removing water from electronics. And air! A little heat doesn’t hurt either.

Fished one out of the sink a week ago and luckily I got there before it shorted itself to death. Still flying! Luck.

The best way to waterproofing the drone is B7000 glue! glue can pour contacts and then remove without residue with tweezers. B7000 can be completely removed without solvent by winding on tweezers. Where I live long winter and rainy spring and autumn so i know what i'm talking about. I filled the boot button and exposed connectors with B7000 glue, and then easily removed them when I needed them in a new build. b7000 can clog the UFL antenna connection without fear of losing connection. I don't like MG Chemicals because it leaves a lot of dirt and is very difficult to remove with a solvent. And also it is very fluid and floods the places that I try to avoid. In this old video, a guy shows how easy it is to apply and remove B7000 glue with tweezers from a flight controller: ukposts.info/have/v-deo/qahejoptjaVn2Zs.html And this glue is very cheap and sold everywhere, as it is very popular for gluing smartphone screens

Try using your underr desk light to see conformal coating. It might be blue/purple enough to see the coating

Hahahaha JB, that intro. You crack me up!!!!

Jeeeez Joshua, that fill light from the pool makes you look like youre in a professional video production studio.

Still works....like 👍

My mobula6 HD also took a plunge, I put it on a infrared heating panel with a fan for 24 hours. And boom, it still worked!

Contact cleaner will clean conformal coating off of anything you need it off of(save camera sensors, and possibly barometers), and will ensure that the component gets working again. It may take a couple applications and some scrubbing with a toothbrush, but it will get it working again.

This vid couldn't have came at a better time lmao I fly around my back yard and did so with COMPLETE CONFIDENCE....until the pool went up....lol I am scared to death to fly around water lol oddly enough my quad fail safed in the exact spot where the pool is located before it went up and that added to the anxiety of flying in the yard lol have some of the worry free so I'm going to try it since I have it already 😁 and apply it to my new mobula7 1s elrs whenever I can get another one😒 this was an awesome review JB and I take my hat off to you for doing it since it is extremely hard to find a mobeetle right about now lol 👍🏽✌🏽oh and I almost forgot PLEASE TRY THE MOBULA7 1S ELRS IT IS AWESOME but make sure your running the new betaflight lol I bricked my gyro however I do think I just had a bad FC because I never flashed anything to it....👍🏽

Hey Joshua, what about the goggle feed after the dunk? I’ve had issues with the sensor in some quads after a good swim in the pool. If you’re careful, applying conformal coating around the seals can help a good bit. You earned your like 👍

I bought conformal but have not used it! Thanks for biting the bullet for me buddy. I guess now I'll use it! Glad your quad is ok.... Let us know how it is in a week!

a hairdryer works well too i was my quads with the hose spray with electrical contact cleaner or isopropyl then dry with a hairdryer been doing it for a few years now never had a quad die

That's the stuff I have but I hated using it because it looks like the board is covered in slime eventually. Once it has enough grass mixed in with it. It does work well though. Now that I have been doing a good enough job at building and not crashing so much, I haven't had to repair a quad in almost a year now. So I keep thinking I need to take them apart, clean them with alcohol and conformal coat everything.

For the USB plug u can use corosiinx 😊

Corrosion X HD is the only waterproofing safe enough for main battery connection and any other small connectors and usb as well but silicone conformal coating is best for everything else, so combined you'll basically have a fully waterproofed quad.

So funny, this video was released just a few hours after I landed my acrobee65 in the garden pond. No conformal coating, did not unplug the battery under water but rinsed the pcb with Flux remover fluid and dried it in the sun. Got lucky, it still flies like a charm

At work (pcb manufacturer) we just use normal transparent spray paint Maybe not the most professional solution but a couple layers of that work just as well + cheaper + more accesible

A food dehydrator works well, if ya have one!

I use spray conformal coating! You just have to be careful!

Question: what is a good combination of analog goggle reciever and antenna for these whoops? I mean, digital is still too heavy for whoops for now imho. Nice experiment and details about conformal coating, mine survived a bucket of rainwater too, no coating. But i did unplug under water, and dry out for 48 hours, then alcohol bath and soft brushing soaking for 25 min, then dry for 3 days, before trying to fly it again. Conformal coating bought, but never used yet. This video reminded me about it, so thank you Joshua.

Instead of conformal coating, I always cover my eletronics with Corrosion X. I live and fly near to the beach. And work great, I have radios, drones and planes working for years. Just apply, a coating once by year. Or if dump into water clean with electrical cleaner and re coat

Priceless knowledge, especially these days! Happy drying 😁

Clear nail polish. works well, comes off easily with alcohol and saves you from anything short of full submersion. For the amount of work most people do to a quad on an ongoing basis, a coating that is 'difficult' is really not so good. Having said that, if you're over water then maybe go all-in with the good stuff.

You literally used logic to prove why people should like the video lol. Nice job.

A couple weeks ago my meteor 75 crashed. Of all the places it could have landed it ended up in my dogs water dish. I got extremely lucky! It still works! How? No idea! No water proofing at all! Great video Josh!

I had a betaflight F3 I never felt like changing and crashed into a drained lake. A mostly drained lake. Needless to say it motivated me to update it to an F4. Keep on the sunny side This was all while an F3 could still handle all of betaflight. No quads have an F3 anymore unless it's been sitting in a closet. I also just got a mobula6 so you make me feel like I'm still in the club lol

I personally have had a Phantom 4 Pro that went swimming in the deep blue ocean on a Natgeo Sharkweek shoot (luckily we had an underwater cameraman, suited up, that immediately free dived down 12m and saved it - what a legend!!) We were still out at sea on the zodiac for a good few hours. As soon as we returned to basecamp, I took my Phantom apart, unscrewed everything and dunked and rinsed my drone in a tub of freshwater for a good 10 minutes, in an effort to get all the salt off the electronics. Afterwards I let all these components in the sun for 2 days, even put it in a box full of rice for another day. After that I sprayed all the electronics with electronic contact cleaner, a product called “mr mckenic”. My drone survived, except the 4k camera, and I fly my drone to this day! (After replacing the camera)! Needless to say, I had no silicon conformal coating on the electronics, prior to the incident. The only other part that had to be replaced was the GPS unit, as expected, as this unit is located in the top part of the shell of the Phantom, and this is the only place I did not open. Of course, the camera and gimbal is the expensive part of the drone, but it was inevitable to lose this part of the drone, sensor got damaged. But still saved me quite a bit of money. Good practice is to spray electronic contact cleaner on your drone parts, if you don’t plan on covering it with conformal coating 🤙

Can you do a video how to clean small motors when they get dusty/dirty? I spray out with degreaser and it works fantastic, even restoring rpm and power.

I use B-7000 glue to waterproof my quads. Have flown in fullpower rain totally fine. Heard conformal coating gets micro-cracks after some cooling/heating cycles + high vibration so it needs maintenance once in a while. B-7000 remains elastic like silicone and much easier to apply and control so that it don’t get in usb ports. In fact i apply it on usb ports with a help of gravity so it hardens like a plug. If I need to use it - just tear it off and reapply it back after to seal and preserve these parts as well. So easy to tear it off as well. You just take one part on tweezers and wind on itself. The only downside is - It has little worse thermal conductivity, but if you fly and not wait on a bench for 5 minutes its totally fine. Is there someone who uses B-7000 as well, or any other substance which you found better in your application? Are there someone using conformal without reapply more than 6 month with no issues in heavy rain?

Try running a thin coat of petroleum jelly around the threads of your conformal coating jar before you put it up, I have used this method on various things over the years that are prone to this

There are different kinds of conformal coatings and not all of them can be soldered through or dissolved in alcohol. so make sure you check

Watching this while my drone is leaned up against a dehumidifier

Cool video about waterproof and a little drone I enjoyed watching you almost destroy your mini

I conformal'd the VTx of my old drone after landing in wet grass killed it. Am looking at ways to waterproof my new one, but it has a barometer that I don't want to ruin. Video appreciated.

hey man love your videos im looking to build an fpv or buy a nazgul evoque i already own a dji fpv drone i am wondering what rc controllers/radios will bind with the dji air unit/caddex vista units if any at all i dont really wanna use the original dji fpv controller or the v2 controller are there any controllers/radios out there that work with those units or would i have to buy a whole seperate control chip or what ever they are and install that ?

you can get little rubber bungs to block the USB ports

Talking to a local store here in Norway, they said acrylic solution is better than silicon when it comes to water resistance. Now, I would think the silicon solution is preferred due to the heat resistant properties that is greater than the acrylic solution? From what I've read and understand based on the local store here, the silicon solution will handle 200C and the acrylic solution resists up to 125C.

I wouldn't recommend coating with things plugged in - I did an ESC plug like that and I could never get it out again, I broke the wings off the plug trying to get it out. I use Kapton tape to mask off anything I don't want coated and then I spray that sucker. Also (I don't know if this only affects the spray-on type) the solvent seems to soften any silicone items such as wire insulation and gummies. I'd probably remove the gummies and try not to get too much on the wires.

Saved my tinyhawk a few times from failure with this. Lost a motor tho. Top tip. 😎

Hey Joshua, I have this Mobeetle6 as well! I'm curious of the ECU temperatures with the coating on. Supposedly if the VTX is running at 400mW, it will lower the power depending on the temperature of the unit. I feel like this coating would keep it from dispersing heat like it should. Just curious! Thanks for the video!

Hey, Just have a little question, do we follow the same protocol if we didn’t thermalcoated it? Thanks a lot for All those infos!!

One thing you missed (probably obvious to you but may not be to new pilots): *Don't conformal coat the motors.* They're already waterproof.

Remember your dru drone shake n bake review ?

Submerging your quad or just getting it really wet is not usually an issue. Even not conformal coated, you just gotta heat everything up with a hair dryer nice and hot, and all the water bakes off. Done it many times, worked every time!

13:10 I go Big Fat Greek /w the Windex, Ethel Alcohol dries faster. Just be aware that there is a polishing compound in Windex, but I've never had a problem with it being conductive... It becomes some dust to brush off b4 applying a coating.

My quads always get the conformal coating treatment, they’ve survived dunks into the bath, in the sink, down the (clean) toilet, and my 5” spent an hour at the bottom of a lake while we tried to find it, when we did the first thing I did was disconnect the battery while still under water, stuck in on a desk fan for a few hours and it was fine, even the Caddx Vista and camera survived.

I like it 👌

Just rescued a 5” from a pond after 2 weeks under water, no waterproof coating applied. Result 1 seized motor, ESC fried. Flight controller, 3 motors, caddy unit and ELRS, were working. Battery was screwed. The rule here is the ESC Diodes cut power first to the rest of the drone.

JB, I have the HS 170 predator small little drone fell in a trashcan full of dirty water I couldn’t find the drone for about 20 minutes finally seen lights flashing at the bottom of a trashcan full of water took the drone out unplugged it dried it with a hairdryer an plugged it back in and flew it. then I had a drone same one laying on some wet grass it was wet and it shorted out, figure that one out!

Hmm thanks for the tips!

That water solution might help with my mobeetle6 board overheating and disabling the gyro

Thanks again for a informative video👍👍 but I wonder. How to conformalcoat a dji air unit? After watching your video I bought the Diatone Roma F5 HD. Really want to conformal coat it since I live in Norway, and it rain or snows "all the time"..

AWESOME video! BTW, did you tested the camera? One of my whoops feel into the pool, then water got into the camera and chlorine destroyed the sensor when it dried! 😢

7:40 Sunlight works great

I have a betafpv meteor 65 that sunk into a washer machine full of dirt water for about 8 minutes, and it survived, is still fully working. I didn't believe when I tested because it's so freaking insane, but is very true...lol

acetone completely removes conformal coating and does not hurt the components, great if you want to clear a board completely

Thanks for the video! But what about the battery? Do you need to cover the balance plug? And if you unplug it from the drone while underwater won’t the water touch the battery electronics and cause a short circuit?

So here's a crazy question... I've got a boatload of Flex Seal left over from a shower project. Would that stuff work?

lol, 13:32, seems like even regular electronics in Joshua's house are powered by xt60 plugs))

I've landed in the lake with pool noodles on the arms and it totally submerged but it still is flying fine but I don't recommend flying over water without coating 😂

Joshua, how many times have you flown over that pool? Must be thousands of times now! You may be able to estimate the odds now. Lol I have been looking to pick up a bottle of the conformal coating for years now. Always out of stock.

My Smart HD PNP from GepRC ended in rain water tank. Was there about 30 secs, after drying it really well it flies like new... no waterproofing done by me. Don't know if some was done by GepRC or if it is even possible to waterproof Vista unit. I guess I was lucky.

hi, new to FPV Drones. Can I use Acrylic Conformal Coating for this?. Thanks

On a roll JB I see the numbers works when you work it. TY for the great info and entertainment in the same takes a talented individual to nerd out and be cool!!

also, like they say with firewood for survival, if you think you have enough for the night, build it 3 times bigger. same for drying your quad lmao, if you think x amount of time is good, times it by 3

I once dropped my 5'' quad into saltwater due to some weird rxloss. It was approx. ankle deep and full of seaweed, so the quad plopped into that mess right to the upper deck. The battery terminals and the ESC power traces had likely shorted out, everything started boiling and fuming, and as a cherry on top the battery caught on fire. While in water. Yeah. I yanked it out having wrapped my hands in my shirt, but the ESC board has been ruined - some power traces eaten clean off the surface. Silicone insulation on some motor wires had puffed up, cracked and turned brittle, and the carbon fiber near the power terminals had visible pitting. To sum up, I had to replace the ESC board, rewire all motors (thankfully the coils themselves were not corroded) and buy a new action camera. That was enough of a lesson to lacquer-coat the boards.

I wonder if there could be some sort of "wetness-fuse" that will immediately cut battery current if it gets wet...

Interesting as always. Did the camera still work?

I have found alcohol not really great at Removing within buttons. I used a conformal coating stripper. Don't ask how I know. What about drone dry it doesn't have the problem of getting it in the ports. Just $$$$

Information I could have used last winter before I flew my tinywhoop into the toilet.