JUST 5 Minutes Every 2 Years so Your Batteries Will LAST FOREVER! Our Prevention Series #2

  Переглядів 844,642

Sweet Project Cars

Sweet Project Cars

2 роки тому

Subscribe to our New Channel / mrknowitallguru
and learn to do almost everything DIY! You can Do this WITHOUT taking your battery out of your car or truck WE ASK YOU DO NOT DO THIS UNLESS YOU HAVE WATCHED THE ENTIRE VIDEO WITH NO SKIPPING THROUGH!!!!!!!
THE BEST Ceramic Coating EVER goo.gl/z9TrgR
SEE This VIDEO if your battery is not holding a charge • How To MAKE OLD BATTER...
Replacing vehicle batteries is expensive, we share how to fix them so they work perfectly for years and years to come and never replace them ever again!
MAKE OLD BATTERIES NEW AGAIN!!! 12v 6v Deep Cycle, Car, Truck, Golf Cart, Semi
Friends the 120V & 220 VOLTS ARE THE POWER INPUTS FROM YOUR HOUSE POWER SOURCE, THEY ARE NOT THE OUTPUT OF THE WELDERS. Here we show the simplest and cheapest way to make cars, trucks, and golf carts, marine batteries last an eternity. We show you the exact method on how to use AC/DC converter welders for reviving your batteries and having them last a lifetime!
Throw out your WD-40, PB Blaster along with all your Slick 50 because we found the best Lubricant for EVERYTHING tinyurl.com/bdf6a6ky
We Guarantee you will love it.
TOOLS:
Welder for For This Video ONLY, use on either standard or deep cycle Batteries amzn.to/3yW4ihK or amzn.to/30k7YNg either will work great, if the Red welder is currently unavailable AS THEY SELL FAST
CAMERA USED FOR VIDEO amzn.to/3pFDsGM
***********************************************
If you would like to help us out.
www.paypal.me/YourSweetProjec...
***********************************************
__________________________________________________
TOOLS:
To Totally revive a Deep Cycle Battery use any of these below
ONLY 6 Volt & 12V Batteries amzn.to/3yW4ihK or amzn.to/30k7YNg
__________________________________________________
Totally Revive a Standard 12-volt Battery us any of these below amzn.to/2K1UsWQ
**If the above welder is unavailable, either one of these will work amzn.to/3mqhebK or amzn.to/3sH4COq ** After doing this process use this charger to slowly full charge the battery amzn.to/3kmCThX
Tools For All Countries:
Distilled Water amzn.to/32notpT
Pic Set amzn.to/3dKiy3w
Trickle Charger amzn.to/36UosJU
Battery Post Cleaner amzn.to/2Z9r7wX
Hydrometer amzn.to/34JLFNn
Shop Towels amzn.to/2P2IDQ5
Venom amzn.to/2qoqfHR
______________________________________________________________
The small compensation we receive from these amazon links helps to keep our channel
available to you.
****Disclaimer****
Due to factors beyond the control of SWEET PROJECT CARS, we cannot guarantee against the improper use or unauthorized modifications of this information. Make sure you check with your manufacturer to make sure this will not affect your factory warranty. SWEET PROJECT CARS assumes no liability for property damage or injury incurred as a result of any of the information contained in these videos. Use this information at your own risk. SWEET PROJECT CARS recommends safe practices when working with tools seen or implied in our video and written content. Due to factors beyond the control of SWEET PROJECT CARS, no information contained on this UKposts channel shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this content is the sole responsibility of the user and not SWEET PROJECT CARS.

КОМЕНТАРІ: 608
@jacobwrona
@jacobwrona 8 місяців тому
I can confirm this works great. I did this on my excavator battery that was too dead to even turn on the gauges. Its been 3 months since performing this procedure and the battery still acts like new and cranks the diesel engine quickly. This may not revive every battery but it won't hurt the value of your battery as a core if you do this and it doesn't revive your battery. Good luck and I hope this saves you a few bucks when everything is so expensive.
@SweetProjectCars
@SweetProjectCars 8 місяців тому
It sure does work Jacob! Glad we could help! Thank you for the view and sharing your stupendous results! Hope you have a great week my friend. mad Mike & team
@athrunzala5337
@athrunzala5337 7 місяців тому
@@SweetProjectCars I have a battery that has been sitting for 5 years should I use caustic soda to clean it first then do this process with the welder? should I buy new acid?
@johnr8439
@johnr8439 2 роки тому
Your doing whats known as an equalization charge. Essentially, you are charging the battery at a higher voltage than it is typically charged to help remove built-up sulfate and balance the voltage of each cell. on the battery. Lead acid battery's only, never on AGM or lithium batteries.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you for watching and sharing John, have a great day. mad Mike the hammer SPC
@tonyann5646
@tonyann5646 2 роки тому
No equalization charges on gel batteries as well..
@Here-2-Learn
@Here-2-Learn Рік тому
Is that the same as desulfurization?
@cphank151
@cphank151 Рік тому
Desulfation is typically done with short pulses of very high charging current with some resting between pulses to prevent the battery overheating. I assume your welder is set for DC reverse polarity so you won't be discharging at high current. This generates a lot of hydrogen for which is very explosive so be careful. Don't allow any sparking when connecting/disconnecting.
@jsun3117
@jsun3117 Рік тому
@@cphank151 Hence why he unplugs his welder from the outlet prior to disconnecting the cables.
@HUBBABUBBADOOPYDOOP
@HUBBABUBBADOOPYDOOP 2 роки тому
Thank you for another video, Mad Mike. May Almighty God Bless you and Family.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Blessings to you and yours as well Hubbabubba, we truly appreciate your view and comment, thank you my friend. mad Mike the hammer SPC
@Kobafied
@Kobafied 2 роки тому
I have a pair of AGM Optima 31T Yellow Top batteries ($375 each) since 2003 in my boat and they are as good as new. They sit on a marine battery maintainer 24/7/365. I take them out every year and test them on a 1,000 amp battery tester, and surprisingly they are good. My point here is that, if you take care of your batteries as shown in this video, even lead acid batteries can last indefinitely. Good video sir - you’re a National Treasure. Happy Holidays all! BTW, the high amps from the welder is cleaning the deposits off the lead plates, which acts like an insulator that reduces a battery’s voltage. Simple science that works.
@SweetProjectCars
@SweetProjectCars 2 роки тому
You are correct WayneRite! Thank you so much for watching and sharing, we really appreciate it, hope you have a great week my friend. mad Mike the hammer SPC
@scottfenton7607
@scottfenton7607 2 роки тому
I wish that I had one of those charges or arc welder machine! I have a 110 mig welder & I'm sure that it wouldn't work.
@j.t.cooper2963
@j.t.cooper2963 Рік тому
That's when Optima's were still made in the USA. Now they are made in Mexico and are total garbage.
@whatsit2ya247
@whatsit2ya247 Рік тому
@@scottfenton7607 I was wondering the same thing about my mig
@TristanVash38
@TristanVash38 9 місяців тому
To add a bit more clarification to your last statement, *acts like an insulator that reduces a battery's voltage and reduces the flow of amperage. Otherwise, well stated!
@SweetProjectCars
@SweetProjectCars 2 роки тому
Dear Subscribers We would like to give a great big SHOUT OUT to EMMANUEL KOUKOULAS for Donating to our channel!! Now if you want to keep those batteries in TIPTOP shape then this is the video for you! This is part of our winter 2021 prevention series ***Quote of the week: If you Talk common sense to a fool he will call you foolish.**** Euripides
@Bozemanjustin
@Bozemanjustin 2 роки тому
You'll never have dry turkey if you do it right. Dissolve 1 lb of brown sugar 1 lb of salt couple tablespoons of Ginger tablespoon of allspice tablespoon of cinnamon tablespoon of nutmeg and 1/2 teaspoon black pepper in water Marinate the turkey overnight in this marinade. The next day remove the bird dry it fully with paper towels. Then rub softened butter over the entire bird. Now place in a 450 oven until internal temperature of the breast is 160 degrees fahrenheit. Remove and let's sit on counter for at least 15 minutes. Now enjoy your juicy bird with subtle flavors of the holiday season because of the spices. You're welcome
@BrettASpitzer
@BrettASpitzer 2 роки тому
How long on and off for a moto battery? About to put mine to sleep for a year and want it to fire up when I return from the middle east!
@tellmesomething2go
@tellmesomething2go 2 роки тому
how much did he donate?
@punker4Real
@punker4Real 2 роки тому
Why Not just swap it with a capacitor set up and a mini SLA way more reliable
@carmichaelmoritz8662
@carmichaelmoritz8662 2 роки тому
i have to do this every time i use my mobility scooter till near dead. it increases the batteries amp hrs use. when i normally charged the batteries to the full shut off they only lasted a days use and when i so called let them boil for a bit after they reached full normal charge i got three days use out of them . bad thing is though nothing lasts forever , even batteries. they will eventually fail over time and go dead quick under a load.
@tomwhite2368
@tomwhite2368 2 роки тому
You've got some amazing content!! I'm loving you're videos,you sir have earned another subscriber!!!
@SweetProjectCars
@SweetProjectCars 2 роки тому
Welcome aboard! Thank you very much, Tom, we truly appreciate the view and comment, hope you have a fantastic day my friend. mad Mike the hammer SPC
@jirojosephesman8175
@jirojosephesman8175 2 роки тому
Great video...your a blessings in disguise.... Thank you have a blessed day and be blessed
@SweetProjectCars
@SweetProjectCars 2 роки тому
You are so welcome, we appreciate the view and share my friend. Hope you have a blessed week. mad Mike the hammer SPC
@gregorycuarino9645
@gregorycuarino9645 2 роки тому
Thank you for your time and help 😊 🙏
@SweetProjectCars
@SweetProjectCars 2 роки тому
Happy to help Gregory! Thank you so much for watching, we truly appreciate it, hope you have a great week my friend. mad Mike the hammer SPC
@Rampage00769
@Rampage00769 2 роки тому
Had turkey deep fried many years ago. Won't eat it any other way. Well maybe roasted lol. Also been a subscriber for many years as well. Great dependable knowledge, and info. Love the channel.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you Rampage! We really appreciate the view and comment, hope you have a Merry Christmas & Happy New Year from the team at Sweet Project Cars.
@silvergrizzly316
@silvergrizzly316 2 роки тому
I hafta tell ya folks, Mad Mike has vast knowledge of all sorts of ingenious ideas... Sweeeeeeeeeeeeeeeeet!!!! 👍👍
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you Jay!! We truly appreciate the view and comment, always a pleasure my friend! Have a stupendous week. mad Mike the hammer SPC
@mlbaker40
@mlbaker40 2 роки тому
Okay, so I DID IT!!!! I bought the red welder and did exactly what you said. Brought it to a boil, bubbles popping out. Max 115 current. Thank you thank you thank you. Unfortunately I have an agm battery in another car. Never again agm. You're the best!!!!!!!!
@SweetProjectCars
@SweetProjectCars 2 роки тому
Excellent! Thank you for watching and sharing your great results M, we truly appreciate it, hope you have a fantastic weekend my friend. mad Mike the hammer SPC
@khanswaleh5
@khanswaleh5 2 роки тому
During boiling is the welding plant connected to house electric supply?
@landasales1
@landasales1 Рік тому
It would have to be, can hear it still running until at the end of the video he tells you when to turn the welder off.
@MichaelR58
@MichaelR58 2 роки тому
Good informational video , thanks for sharing , God bless !
@SweetProjectCars
@SweetProjectCars 2 роки тому
Our pleasure! Thank you for watching Michael, we truly appreciate it, hope you have a blessed week my friend. mad Mike the hammer SPC
@cdogg1787
@cdogg1787 2 роки тому
I do believe the "smoke" from the battery is hydrogen gas. Make sure you don't arc anything when you do this! Great video, I am buying that welder
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you for watching, cdogg, have a great day! mad Mike the hammer SPC
@wngimageanddesign9546
@wngimageanddesign9546 2 роки тому
I got an easier tip to never have a dead battery. Install a 5W solar panel in your rear deck of the car and wire it to the battery. It will keep the car trickle charged daily when in the sunshine and never allow the battery to drop in voltage to the point of sulfating. It counters the constant 10s of milliamp drain on the sitting car's battery. Great for anyone parked outside and don't drive their cars often, like city dwellers. If the car is stored indoors, buy yourself a Battery Tender.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you for watching and sharing, we really appreciate it, have a great week my friend. mad Mike the hammer SPC
@8632tony
@8632tony Рік тому
I'm retired and drive my Ranger about 250 miles per year, so it was not uncommon for me to find my battery dead when I needed to go somewhere. I got tired of buying a new battery every year, so I bought a 20 watt solar panel off eBay (about $25), a 5 amp controller from AliExpress (little over $5) I just laid the solar panel in the bed of the pickup, ran a wire under the door to the controller I had hung on the back of the seat and plugged the controller into the cigarette lighter. The controller has a light on it to indicate when the battery is fully charged and I can see it from the kitchen window (that's why I hung the controller on the back of the seat.) I look out the window and if I see a green light, I know the battery is fully charged. I haven't had to replace the battery for six years and it's always ready to go when I am. If you have to leave the solar panel under the front or rear windshield, get the biggest one you can conveniently deal with as the glass will drastically reduce the panel's output. Those little 1.5 watt panels are useless behind a windshield, so don't waste your money on one.
@KrustyKlown
@KrustyKlown Рік тому
should be a standard feature on ALL CARS .. a built-in solar trickle charger.
@arkrainflood
@arkrainflood Рік тому
make sure the panel includes a diode! otherwise the panel will DRAIN the battery if no sun.
@solotango5576
@solotango5576 Рік тому
@@KrustyKlown LOL I can hear the lobbyists now xD
@ronarmstrong835
@ronarmstrong835 Рік тому
As I sit here watching this, I can't help but imagine that its totally possible to build something like this into a car's circuitry. Given that everything is computer controlled. In other words, every two years your car could run a diagnostic and do this automatically. Obviously none of the car companies want to do this because they want to help their friends in the battery industry sell batteries.
@SweetProjectCars
@SweetProjectCars Рік тому
We're with you on that Ron!! It all comes down to the companies making more and more so the consumer ends up getting the shaft. Your idea is fantastic! Thank you for watching and sharing your input is appreciated. Have a great week and Happy New Year. mad Mike the hammer SPC
@chriskennedy7534
@chriskennedy7534 2 роки тому
I connect a charger every time I service the vehicle. A thorough charge, equalisation, a few times a year is much kinder on plates than cooking it every 2 years Prevention saves issues, compared to using the radio or lights when engine is not running, that's a killer
@miketonon7946
@miketonon7946 10 місяців тому
I have two 6 year old batteries. How long should I cook them for?
@SweetProjectCars
@SweetProjectCars 9 місяців тому
I hear you chris!! Thanks for watching and sharing, have a fantastic day my friend. mad Mike
@marriocharles4168
@marriocharles4168 Рік тому
Great Video there Mike. May you please indicate after how many minutes the increments of different voltages are adjusted? I'm eagerly looking forward.
@SweetProjectCars
@SweetProjectCars Рік тому
Please watch the video a couple more times, you will see. We start out on the lowest voltage for the whole process, that should take care of the job for you Marrio. Thank you for watching, watch this video as well ukposts.info/have/v-deo/jomln6RkhZWhlac.html it has a lot of helpful information about this method. Have a great day and all the best on your project my friend. mad Mike the hammer SPC
@jayjaynella4539
@jayjaynella4539 2 роки тому
I recycle metals as a hobby and money earner. Son just delivered me a load of fairly new car batteries, supposedly maintenance free. Most fairly new, showed green or black eyes. But not enough to turn a starter motor. I picked a few and removed the caps from the maintenance free batteries. Some caps easy to get off, many are quite difficult. All the batteries had no liquid visible anywhere. Even though the eye was a green or black colour, the battery was not really useful. I even added demin water to 1 but could not get enough response. It appears the battery makers are making topping off the battery cells an impossible task to heighten their profits, part of being green sustainable. What a waste to the environment, batteries needing to be replaced needlessly. If you see a company using the word sustainability or any of its variants, the company is really talking about its profits and the use of those words have nothing to do with the environment.
@SweetProjectCars
@SweetProjectCars 2 роки тому
We're with you on that, jayjay! Thank you for watching and sharing, have a great day my friend. mad Mike the hammer SPC
@joshuaneal4125
@joshuaneal4125 2 роки тому
Would have loved to seen this last year! After buying 3 boat batteries, zero turn battery, v star 950 battery, F150 battery, etc my cost was well over $800
@SweetProjectCars
@SweetProjectCars 2 роки тому
Ugh, that's terrible Joshua! Well now you have the information to take care of them from here on out. Thank you for watching and sharing, have a great day. mad Mike the hammer SPC
@markc9400
@markc9400 2 роки тому
Love your videos. Do you have any input on welding with the Amico machine? Longevity, quality? Thanks. Be well and have a great New Year.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Hello Mark, we have a few of the Amico machines, they are great quality my friend. Thank you so much for watching and asking, we really appreciate it, hope your 2022 is going well. mad Mike the hammer SPC
@kylemlm
@kylemlm 2 роки тому
Mike...Battery shortage is big issue. Thank you for the video and the secret..
@SweetProjectCars
@SweetProjectCars 2 роки тому
It sure is Kyle! Everything is lately :( Thank you so much for watching and sharing, hope you have a great week my friend. mad Mike the hammer SPC
@1erinjames
@1erinjames 2 роки тому
Brilliant!! Great video!
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad you enjoyed it Erin! Thank you so much for watching, we truly appreciate it my friend, hope you have a great weekend. Cheers! mad Mike the hammer SPC
@tbos.
@tbos. Рік тому
You sure are one funny engineer, lol. Thanks for your unique and amazing diy videos.
@SweetProjectCars
@SweetProjectCars Рік тому
LOL Glad you like them! Thank you for watching and commenting, have a great weekend T BOS. mad Mike the hammer SPC
@felicelgato59
@felicelgato59 2 роки тому
Merry Christmas, thanks for another wonderful video
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you, it's our pleasure! Hope your holidays were the best, thanks for watching and sharing my friend. mad Mike the hammer SPC
@dragan3290
@dragan3290 2 роки тому
I subbed and liked yesterday. Every couple of hours I'm liking ? How w many vids?😂👍. Never put acid in water, especially hot water. But you can add water to acid, distilled of course. Top videos. Cheers from Australia 🙂👍👍👍
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you for watching and sharing, Dragan! Cheers to you my friend, we are glad to have you here with us Australia! mad Mike the hammer SPC
@tonyann5646
@tonyann5646 2 роки тому
Bought a Korean built vehicle new in 2010. Was fitted with a Korean made battery which lasted 11 years. Certainly a record in my experience.
@SweetProjectCars
@SweetProjectCars 9 місяців тому
Thanks for watching and sharing tony, have a great day my friend. mad Mike
@alexguzman5547
@alexguzman5547 2 роки тому
😅 Charge the brother in law and mother in law. Thanks for another great video, Mike. TBH, I'll still pull my battery if I'm going to do this though. I don't trust sulphuric acid, and especially not hot sulphuric ACID, but I accept proof that it can obviously be done in place. Have a most blessed season. 👍👍
@SweetProjectCars
@SweetProjectCars 2 роки тому
LOL, thank you so much for watching Alex! Blessings to you and yours, Merry Christmas my friend. mad Mike the hammer SPC
@juriedekock6154
@juriedekock6154 2 роки тому
Start on low setting....only go to higher setting of welder if all the battery cells does not "boil"
@bassthis
@bassthis 3 місяці тому
Mike, The ARC MMA Welder 160A Welding Machine is listed as 110V - 220V. The plug attached to unit is 120v also I dont see a voltage selector switch anywhere. Plug attached to unit is 120 volt type. How do you feed 220v to this welder?
@paulpaine8231
@paulpaine8231 2 роки тому
Can this welder be used for the 15 minute, repeat 5 times, battery rejuvenator you show in another video. The Associated charger youuse in your other video is 3X the cost of this welder. I would rather have the welder for 1/3 the cost. Thanks for all the terrific videos. I own a few classic cars, and these tips save me a ton.
@SweetProjectCars
@SweetProjectCars 2 роки тому
This ukposts.info/have/v-deo/jomln6RkhZWhlac.html is the video, it's our update to this process rather than the charger video, the SHOW MORE will instruct you on which welder to use for a standard battery and a deep cell battery, Paul. Thank you for watching and asking, hope you have a fantastic week my friend. mad Mike the hammer SPC
@georgesmith8113
@georgesmith8113 2 роки тому
Excellent!! 👍👊😎
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad you liked it George! Thank you so much for watching and sharing, we truly appreciate it, have a fantastic day my friend. mad Mike the hammer SPC
@Jayson90210
@Jayson90210 2 роки тому
Man, I have seen this before and it does work..Now, has anyone got a welder I can borrow..lol Thanks for the Video! Merry Christmas to you and your family, and everyone watching 🎅🤶
@Hitomaru-shiki.sensha
@Hitomaru-shiki.sensha 2 роки тому
even the little charger with desulfate mode work but it takes longer
@SweetProjectCars
@SweetProjectCars 2 роки тому
LOL, It's our pleasure to share Jay Bob! Thank you for watching, Merry Christmas to you and yours my friend, have a great week. mad Mike the hammer SPC
@wayneshipman7406
@wayneshipman7406 Рік тому
Thanks for the info
@SweetProjectCars
@SweetProjectCars Рік тому
Our pleasure Wayne! Thank you for watching, have a great day. mad Mike the hammer SPC
@marriocharles4168
@marriocharles4168 Рік тому
Marvelous! I'm elated by this video by Sweet Project Cars.
@SweetProjectCars
@SweetProjectCars Рік тому
Glad you liked it! Thanks again Marrio, hope you have a great week. mad Mike the hammer SPC
@saulflores1044
@saulflores1044 Рік тому
Hi Mike Thanks for all your info. Can this be done with a charger instead of the welder? And at what setting would I have to do it for the 5 minutes? I figure at 200amps by let me know if I got it wrong and it has to be only with the welder? Thanks again in advance.
@SweetProjectCars
@SweetProjectCars Рік тому
See this ukposts.info/have/v-deo/jImJrG1nhKd7jmQ.html it's our oldest video on this method, however, this method ukposts.info/have/v-deo/jomln6RkhZWhlac.html is our update and works best and is far more economical. Hope this helps, thanks for watching have a great day. mad Mike the hammer SPC
@saulflores1044
@saulflores1044 Рік тому
Thank you! God bless you!
@subbangovender3476
@subbangovender3476 Рік тому
Could you send us a recipe for the fried turkey and thanks for your wonderful and informative video
@SweetProjectCars
@SweetProjectCars Рік тому
You just need this amzn.to/3pXGPcN then follow the instructions included with the fryer. It's fantastic, you will never eat another baked turkey again my friend. Thank you for watching and commenting, we really appreciate it, have a great week. mad Mike the hammer sPC
@charlesduzzie9811
@charlesduzzie9811 2 роки тому
Merry Christmas Sweet .... And Happy Holiday Julio...... 🎄
@SweetProjectCars
@SweetProjectCars 2 роки тому
Merry Christmas & Happy New Year to you as well Charles! Thank you for watching. mad Mike the hammer SPC
@chriskolar
@chriskolar 2 роки тому
Thanks for the cool tips
@SweetProjectCars
@SweetProjectCars 2 роки тому
Our pleasure Chris! Thank you for watching, we hope you have a Merry Christmas & Happy New Year from all of us here at Sweet Project Cars.
@hunybilliches
@hunybilliches 9 місяців тому
PLEASE CONFIRM ... Do I leave the welder setting at it's lowest that will make it boil for 5 minutes as you say at the beginning or ... do I go ahead and crank it up for maximum boiling for 5 minutes as you say towards the end? Thank you for the great videos !
@SweetProjectCars
@SweetProjectCars 8 місяців тому
Start out on the lowest setting, then gradually turn it up until you get a consistent boil on all of the cells then follow the video instruction regarding timelines etc. Hope this helps, have a great weekend, thanks for the view. mad Mike
@kendellmarlin6739
@kendellmarlin6739 2 роки тому
I try this today it really really work 👍
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad we could help Kendell! Thank you for watching and sharing, have a great week my friend. mad Mike the hammer SPC
@BruceLyeg
@BruceLyeg 2 роки тому
That Julio is a crazy guy. Happy Holidays Mike
@SweetProjectCars
@SweetProjectCars 2 роки тому
He sure is Bruce! Thank you so much for watching, Merry Christmas & Happy New Year my friend. mad Mike the hammer SPC
@opiojoel4272
@opiojoel4272 2 роки тому
Great video👊. Just wondering would this trick work on motorcycle batteries. The 6.5ah small batteries?. Happy holidays
@SweetProjectCars
@SweetProjectCars 2 роки тому
It sure will, just cut all timelines in half for that size opio joel. Thank you for watching and asking, Happy New Year to you my friend. mad Mike the hammer SPC
@goodguygto
@goodguygto 2 роки тому
That's a good battery!, ACDelco "GM"!👍 Then again it's actually a Interstate Battery!!👍👍😎
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thanks for watching and sharing goodguy! Hope you have a fantastic week my friend. mad Mike the hammer SPC
@geraldito7777
@geraldito7777 2 роки тому
Ill try today🙂thanks
@SweetProjectCars
@SweetProjectCars 2 роки тому
Awesome! Thank you for watching and sharing, have a great week my friend. mad Mike the hammer SPC
@otobulakenyo2664
@otobulakenyo2664 2 роки тому
Can i use a non inverter type of welding machine? is there no need to top up the battery with distilled water? Thank you so much sir for this very informative tip.Godbless and more power
@SweetProjectCars
@SweetProjectCars 2 роки тому
Please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process. Thanks for watching and asking Oto, have a great week. mad Mike the hammer SPC
@juriedekock6154
@juriedekock6154 2 роки тому
Only invertor [DC] welder, not old heavy transformer type AC welders. Fill cells just to cover the plates !! Do not fill up completely.
@christopherwilliams4647
@christopherwilliams4647 2 місяці тому
I have a charger on my boat that does this. It’s called equalize mode. It even improves brand new batteries. My new trolling motor batteries fully charged sat at 12.6 static voltage now they’re at 12.9. This method does work!
@a.c.e.7568
@a.c.e.7568 Рік тому
Well I got over 14 and 16 years out of factory installed "Panasonic" batteries in our Honda and Toyota in weather that goes from 30C to -25C. The trick is topping up the battery with distilled water every couple of years and a properly vehicle charging system. Your boiling of the battery is "cell equalization" which can only be done to a standard flood leaded acid (FLA) battery, not an AGM or GEL battery. Some chargers have that feature, or you can simply use the "winter" snowflake charging mode (higher voltage) in the summer.
@SweetProjectCars
@SweetProjectCars Рік тому
We've found that the option on chargers doesn't work like our method does. Thank you for watching and sharing A.C.E. have a great week. mad Mike the hammer SPC
@dallaste462
@dallaste462 2 роки тому
After this process Do you change out the battery fluid with new? Just wondering if there is any contamination to the fluid that would need to be changed
@SweetProjectCars
@SweetProjectCars 2 роки тому
It's not necessary dallaste462. Thanks for watching and asking, have a great day. mad Mike the hammer SPC
@jeffreprogle7958
@jeffreprogle7958 2 роки тому
I use standard 6 volt car/tractor batteries (not deep cycle) in restored WW2 military vehicles. I also need a good starter welder. Which model do you recommend? Of course I will also be using it on 12 volt car and truck batteries.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Hello Jeff, amzn.to/3yW4ihK or amzn.to/30k7YNg either one of these are a great choice, it's what we use. Thank you for watching and asking, we really appreciate it, have a great week my friend. mad Mike the hammer SPC
@randyo308
@randyo308 2 роки тому
Well that video gets a “subscribe/notify/like” from me lol. Great info!!
@SweetProjectCars
@SweetProjectCars 2 роки тому
Awesome! Thank you Randy, welcome aboard, we really appreciate the view and comment, hope you have a fantastic day my friend. mad Mike the hammer SPC
@SalmanKhan-ir9gw
@SalmanKhan-ir9gw 2 роки тому
Marvelous work dear is that safe for battery separators and plates may be they burn on that high amperage and volts, what about batteries that already have 12.6 volts i will be really appreciated if you answer these questions good luck and keep it up
@SweetProjectCars
@SweetProjectCars 2 роки тому
This is safe for all wet-style batteries my friend. If you already have 12.6 volts, this is still a good method to do every 6 months and you won't be replacing that battery. Thank you for watching and asking Salman, have a great week. mad Mike the hammer SPC
@SalmanKhan-ir9gw
@SalmanKhan-ir9gw 2 роки тому
@@SweetProjectCars Question 1: how much time for 40AH amp battery, 100AH amp battery, 150AH amp battery, 200AH amp battery ? Question 2: if i do this on discharged battery it will take lot off time should i charge first then do your procees ? Question 3: can i do the same process on normal lead acid batteries not a deep cycle or change the timmings ? Friend these questions are very important for me i will be really appreciated if you answer these questions good luck and keep it up
@tinof5829
@tinof5829 2 роки тому
Are the numbers you are stating from the welder, DC amps? Thank you.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Yes. Thank you for watching Tino. mad Mike the hammer SPC
@francoisverdoes8552
@francoisverdoes8552 8 місяців тому
I got a matweld dc inverter 200 amp,but it wouldt not work,why is that?So i borrow a friends universal 160 amp dc inverter and it work,thank you sir .Question why wouldt my matweld not work?
@SweetProjectCars
@SweetProjectCars 7 місяців тому
We only recommend using the posted products/tools shown in the video description as they have been rigorously tested by our team here at SPC. Thanks for watching, have a great week. mad Mike
@gailmrutland6508
@gailmrutland6508 2 роки тому
*Something kept bugging me to watch this vid, as I am designing a off grid solar cabin setup and have been laboring over using low cost FLA 's or going LI on and break the bank. The issue was longevity, and now that is no longer a problem with your technique. I cannot thank you enough, My God Bless. ( yes i have access to on grid power to do the treatment when necessary!)*
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad we could help, Gailm! Thank you for watching and sharing, we really appreciate it, have a great week my friend. mad Mike the hammer SPC
@juriedekock6154
@juriedekock6154 2 роки тому
For nothing you get nothing and very little for a sixpence.......
@patrickt863
@patrickt863 Рік тому
What welder are you using? I have a golf cart with 6-6 volt batteries. The batteries are all matched. Do you think I can take a pair in series and do both at the same time like a 12 volt battery?
@SweetProjectCars
@SweetProjectCars Рік тому
We are using this ukposts.info/have/v-deo/jomln6RkhZWhlac.html and yes, you can do them in series Patrick. Thanks for watching and asking, have a great week and all the best on your project. mad Mike the hammer SPC
@andrewsj65
@andrewsj65 Рік тому
I have a Lincoln MIG welder. Can this be done with a wire feed welder. Thanks
@SweetProjectCars
@SweetProjectCars Рік тому
Please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process. Thanks for watching and asking, have a great week. mad Mike the hammer SPC
@brianwacasey6016
@brianwacasey6016 2 роки тому
Thanks for the video. By regular household current for the welder, do you mean 120v 15a,20a, or 30a? With the welder set at the "22" that you started at, does that draw 22amps? Thanks
@SweetProjectCars
@SweetProjectCars 2 роки тому
The most common electrical outlet in any home is a 110 volt. Sometimes you may hear 110 volt plugs referred to as 120 volt. Do not be confused by this; think of them as one and the same. Hope this helps Brian, thanks for watching, have a great day. mad Mike the hammer SPC
@marksandlin8376
@marksandlin8376 2 роки тому
Think in watts and it makes more sense, volts x amps. your welder is putting out a lower voltage at a higher current. Example, 15V x 22A = 330W. Your welder will be drawing a bet more from the power outlet because nothing is totally efficient, so maybe 350W. So 350W ÷ 120V = 2.9A, so about 3A.
@brianwacasey6016
@brianwacasey6016 2 роки тому
Btw, Ronnie says he can take Hoolio easy peasy lemon squeezy! Or should we say "squeegy? Lol
@flacoanemico5199
@flacoanemico5199 2 роки тому
No, the welder steps down the voltage and tho the welder says 22 amps it is not drawing 22 amps. Its like a transformer but it uses mosfets.
@natgasf4097
@natgasf4097 2 роки тому
So at what amperage does the welder operate at 15 or 20 amps?
@jirojosephesman8175
@jirojosephesman8175 2 роки тому
Quick question...? I do have dewalt 4amp charger and maintenance charger, is it ok without being 200 amps as you recommended? I drain all the acid out pour in distilled water and charge? Every hour then 15 min rest intervals? Thank you again..happy holidays to you and your family circle as well ..God blessed
@SweetProjectCars
@SweetProjectCars 2 роки тому
This works on wet-style batteries only Colin. Thank you so much for watching, hope you have a great week my friend. mad Mike the hammer SPC
@whatsit2ya247
@whatsit2ya247 2 роки тому
@spc, I think you misunderstood the question.
@celticlightning9703
@celticlightning9703 2 роки тому
That is one tip that is the best I've seen out of my 49 years.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad to help Brian! Thank you for watching and commenting, we really appreciate it, hope you have a fantastic day my friend. mad Mike the hammer SPC
@yulafewa5298
@yulafewa5298 Рік тому
Was going to try this out, unfortunately the welder is causing the breaker to trip. Do I need a dedicated high amps circuit for the welder?
@SweetProjectCars
@SweetProjectCars Рік тому
It works with standard household power, if you have that and it's still tripping the breaker, it may be something wrong with the welder, send it back for a replacement Yula. Thanks for watching, have a great week and all the best on your project my friend. mad Mike the hammer SPC
@dennislintz1
@dennislintz1 Рік тому
Does it matter what kind of welder I use? Can I use my 125 Amp Chicago Electric Flux core welder from Harbor Freight?
@SweetProjectCars
@SweetProjectCars Рік тому
You need this amzn.to/3yW4ihK Please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process. Thanks for watching and asking, have a great week. mad Mike the hammer SPC
@paulzlens
@paulzlens 2 роки тому
cant wait to try this
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad we could help, Pavel! Thank you so much for watching and commenting, have a great week. mad Mike the hammer SPC
@fredblankenship2319
@fredblankenship2319 Рік тому
will the tooliom welder revive deepcycle batteries as well as the standard batteries?
@SweetProjectCars
@SweetProjectCars Рік тому
It works flawlessly every single time using either of these welders for standard battery amzn.to/2K1UsWQ or deep cycle amzn.to/3yW4ihK Thanks for watching, have a great day. mad Mike the hammer SPC
@rmckelvy15
@rmckelvy15 2 роки тому
Happy holidays Mike
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you Ronnie! Merry Christmas and Happy New Year my friend, we really appreciate all of our great subscribers like you. mad Mike the hammer SPC
@ramonlopeznote
@ramonlopeznote 2 роки тому
Hey, you can really roll the Spanish "r". That is worth a gold medal! The most difficult thing for Americans, really, when speaking Spanish. Thanks for your videos dude. I am going to try this myself since I have got all the tools needed and 3 past dead batteries to experiment with. Well deserved "LIKE IT"
@SweetProjectCars
@SweetProjectCars 2 роки тому
LOL, Thanks Ramon, I appreciate that :) I learned from the best..... Hoolio :) Thank you for watching and sharing, we really appreciate it, hope you have a great week my friend and all the best on your project. mad Mike the hammer SPC
@lovemytechy
@lovemytechy 2 роки тому
So optima yellow too can be done this way? No difference in AGM batteries? Do all 12v batteries shave a way to be topped off?
@SweetProjectCars
@SweetProjectCars 2 роки тому
This works on all wet-style batteries Deb. Thanks for watching. mad Mike the hammer SPC
@edwardkane3237
@edwardkane3237 2 роки тому
Have you ever rejuvenated a garden tractor battery ? We have a lawn service and we own several zero turn and stand on mowers. Seems like the best I can get is two years out of our batteries. We store then up here in NE Ohio with a battery tender in the off season and the best I’ve ever had a garden tractor battery last is 3 years…
@SweetProjectCars
@SweetProjectCars 2 роки тому
This works on all wet-style batteries, we have done this on all types like motorcycle, garden tractor etc. Thank you for watching and asking Edward, watch this as well ukposts.info/have/v-deo/jomln6RkhZWhlac.html it has lots of helpful information about this process. Have a great week my friend. mad Mike the hammer SPC
@HonestHomesteading
@HonestHomesteading 5 місяців тому
How long do you let the battery cool before putting the caps back on? And is it necessary to run the trickle charger after doing this?
@SweetProjectCars
@SweetProjectCars 5 місяців тому
Once you're done doing the charging, put the caps back on, and it's always good to put a trickle charger on it until the charger says the battery is fully charged it could take up to 24 hrs. Thanks for watching and asking, have a fantastic week my friend. mad Mike & team
@philipward8242
@philipward8242 2 роки тому
Really Nice
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad you liked it Philip! Thank you for watching and sharing, have a fantastic week my friend. mad Mike the hammer SPC
@billy2bob63
@billy2bob63 2 роки тому
Just to add NO SMOKING or no sparks while doing this!!!!!! Please don't use your cigarette lighter to be able to see in the battery cells either! 🚀🔥 Thank Mike
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thanks Kerry, it does take a little common sense, I mean you don't smoke a cigarette when you are filling your car with gasoline do you? :) We appreciate the view my friend, hope you have a great week. mad Mike the hammer SPC
@billy2bob63
@billy2bob63 2 роки тому
@@SweetProjectCars Mike will that yellow one that is rated at 160 amps work for maintenance of a 12 volt car/truck battery?
@garychandler4296
@garychandler4296 2 роки тому
But the lighter trick could help rid the planet of the witless...
@IDK-vs1mg
@IDK-vs1mg 2 роки тому
What are you the fun police 🤨
@calholli
@calholli 10 місяців тому
A little hydrogen flash won't hurt you..
@thedapperpauper
@thedapperpauper 2 роки тому
Graet tip! Q: Can this be done to sealed MF (maintenance free) batteries? The ones that don't have plugs that open at the top?
@SweetProjectCars
@SweetProjectCars 2 роки тому
This works on wet-style only batteries Paul. Thank you for watching and asking, have a great week my friend. mad Mike the hammer SPC
@carlfalk7251
@carlfalk7251 2 роки тому
NO
@xicazen1
@xicazen1 Рік тому
Yes, it works, all batteries had caps, even under stickers, open them and if the battery is an AGM type only put distilled water, do the trick with the welder and it works fine, i did it a lot of times with lead acid, agm and apparently “sealed” batteries.
@martinylores400
@martinylores400 Рік тому
Good day sir i'm martin of the Philippines can i do the same procedure to my 60 volt e-bike battery
@SweetProjectCars
@SweetProjectCars Рік тому
This works on wet-style batteries only my friend. Thank you for watching and asking, have a great day Martin. mad Mike the hammer SPC
@haroldjbilliot9879
@haroldjbilliot9879 Рік тому
what dc welder were you using? and were to purchasr
@SweetProjectCars
@SweetProjectCars Рік тому
It's this amzn.to/3yW4ihK Thank you for watching harold, hope you have a great day my friend. mad Mike the hammer SPC
@shannonlawsonnashville
@shannonlawsonnashville 2 роки тому
I just bought a YESwelder to do this exact deal. But I caught another one of your older videos doing this and you used a specific welder and said that some of them wouldn’t work for this application. Is that true?
@SweetProjectCars
@SweetProjectCars 2 роки тому
Hello Shannon, this method in this video is completely different than our other video, please use the recommended products/tools for each specific video, we test these methods for years and years to know that they work, and work every time and most of all that they are safe for both you and your batteries/vehicles. Thanks for watching, have a great day. mad Mike the hammer SPC
@shannonlawsonnashville
@shannonlawsonnashville 2 роки тому
@@SweetProjectCars thanks for getting back to me
@ferozkhatri8565
@ferozkhatri8565 2 роки тому
sir i have 2 batteries one have showing 12.7v and second have 12.8v but there is cranking amps and backup can i run this procedure on that type off batteries that have 12.6 to 12.8v showing , and what if my battery have irritation cells or damaged cells is that still works, and there is any different procedure for 220v household voltages please reply it is very important to know thanks
@SweetProjectCars
@SweetProjectCars 2 роки тому
This works on wet-style, acid batteries only, if your battery has acid in it and distilled water, this will work. Give it a shot, you've got nothing to lose my friend. Thanks for watching, have a great day. mad Mike the hammer SPC
@dukiepile
@dukiepile Рік тому
Can you please tell me the brand and model of that welder THANKS !!!
@SweetProjectCars
@SweetProjectCars Рік тому
It's this amzn.to/399hh3E and just a reminder, all of the products/tools we use in our videos can always be found in the ...MORE of the videos description, if you can't find it let us know and we will help you. Thanks for watching. mad Mike the hammer SPC
@vijayanmullai
@vijayanmullai Рік тому
Is this method applicable for home inverter tall tubular batteries also?
@SweetProjectCars
@SweetProjectCars Рік тому
This works on all wet-style batteries my friend. Thanks for watching, have a great day. mad Mike the hammer SPC
@paulpaine8231
@paulpaine8231 2 роки тому
Thanks!
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you so much for this Paul! We truly appreciate all of our great subscribers like you, it makes all we do worth it, Hope you have a fantastic week my friend. mad Mike the hammer SPC & team
@ronaldch7365
@ronaldch7365 2 роки тому
Very cool
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad you liked it Ronald! Thanks for watching and sharing, hope you have a great weekend. mad Mike the hammer SPC
@N67414
@N67414 2 роки тому
Unlikely this will work reliably. The normal chemical action of lead and sulfuric acid Will result in slight decline in the integrity of the lead plates over time. Charging reverses the process, but not 100%. “Boiling” a battery is helpful, but a desulfating cycle on some chargers takes a long time. In cases where the deposits are so deep the electrical current can’t get to the material, it’s stuck forever. This is why battery recycling companies salvage the lead and build a new battery. Just keep it charged and or buy a battery charger with a trickle charge desulfating setting.
@SweetProjectCars
@SweetProjectCars 2 роки тому
We have done this process for years and years Clifford, we have batteries that are still going after 20+ years, so it does work my friend. Thanks for watching, have a great day. mad Mike the hammer SPC
@1puppetbike
@1puppetbike 2 роки тому
@@SweetProjectCars ...I'll try it on a 20 year old dead battery and let you know! ..on a serious note.. I wish I would have tried this 20 years ago! Thanks
@roadstar499
@roadstar499 2 роки тому
@@SweetProjectCars i agree..if you have been doing it for 20 years that would be a win win...most batteries don't last more than 4-5 years on average... even if a battery lasted 10 years that's incredible...
@roadstar499
@roadstar499 2 роки тому
would this work using my 110 volt flux core wire welder.??..i think so,just checking...thanks
@SweetProjectCars
@SweetProjectCars 2 роки тому
Please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process. Thanks for watching and asking, have a great week. mad Mike the hammer SPC
@Photostudioww
@Photostudioww 2 роки тому
I have harbor freight 90 amp stick welder will it work with that?
@SweetProjectCars
@SweetProjectCars 2 роки тому
Please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process. Thanks for watching and asking, have a great week. mad Mike the hammer SPC
@D.Macchione
@D.Macchione 2 роки тому
how high of amperage on that welder do you suggest going?
@SweetProjectCars
@SweetProjectCars 2 роки тому
Start off low and gradually turn it up until you have a consistent boil on all cells, just follow the video. Also, watch this ukposts.info/have/v-deo/jomln6RkhZWhlac.html it has more information that will be helpful Michael. Thanks for watching. mad Mike the hammer SPC
@WFHVictor
@WFHVictor 2 роки тому
Can this method be used on smaller 12v sealed lead acid batteries used for ebikes?
@SweetProjectCars
@SweetProjectCars 2 роки тому
This works on all wet-style batteries, you just need to have access to the water inside the battery. Thanks for watching and asking, have a great day. mad Mike the hammer SPC
@domingodeanda233
@domingodeanda233 2 роки тому
That was pretty damn good
@SweetProjectCars
@SweetProjectCars 2 роки тому
Glad you liked it Domingo! Thank you for watching and commenting, hope you have a great day my friend. mad Mike the hammer SPC
@saltycreole2673
@saltycreole2673 2 роки тому
You sound like Adam Corolla! ¡Con mucho gusto Julio! Gracias por haciendo gaso de hydrogenia en su caro desde la bateria libre.
@SweetProjectCars
@SweetProjectCars 2 роки тому
I've been told that before Salty :) Thanks for watching, have a great day my friend. mad Mike the hammer SPC
@saltycreole2673
@saltycreole2673 2 роки тому
@@SweetProjectCars lol!
@joshua_tira
@joshua_tira 2 роки тому
Can this process charge a battery if it is flat say after leaving my head lights on n the car cant start cn i charge it this way
@SweetProjectCars
@SweetProjectCars 2 роки тому
Absolutely Joshua! Thank you for watching and asking, have a great day. mad Mike the hammer SPC
@MT-rv3ec
@MT-rv3ec 2 роки тому
You have 2 tool lists....I am confused. Can the yellow welder be used on a regular 12 volt car battery? And which one is used for deep cycle batteries? I don't want to order the wrong one. Please tell me which one to use for a regular 12 volt car battery. Thanks, Terry
@SweetProjectCars
@SweetProjectCars 2 роки тому
This amzn.to/3yW4ihK you can use for standard 12volt batteries, MT. Thanks for watching, have a great day. mad Mike the hammer SPC
@davidfellows6250
@davidfellows6250 Рік тому
can i use my wire welder if i hold it in place? oh ps and does this work for deepcell batteries?
@SweetProjectCars
@SweetProjectCars Рік тому
This works on all wet-style batteries David, please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process. Thanks for watching and asking, have a great week. mad Mike the hammer SPC
@hamsandwich4830
@hamsandwich4830 2 роки тому
Keep up the great videos. You are a sweet badass. Thumbs up.
@SweetProjectCars
@SweetProjectCars 2 роки тому
Thank you! Will do Ham Sandwich! We truly appreciate the view and comment, hope you have a stupendous week my friend. mad Mike the hammer SPC
@treasure_hunters451
@treasure_hunters451 9 місяців тому
Can I use a trickle charger instead of the DC welder? Thanks.
@SweetProjectCars
@SweetProjectCars 9 місяців тому
No, to have success with this process, you need to use the exact tools/products shown. Thanks for the view, have a great weekend. mad Mike the hammer SPC
@Hitomaru-shiki.sensha
@Hitomaru-shiki.sensha 2 роки тому
does this only work for flooded lead acid. what about AGM?
@SweetProjectCars
@SweetProjectCars 2 роки тому
This works on wet-style only batteries. Thank you for watching, have a great week my friend. mad Mike the hammer SPC
@MrNebRebew
@MrNebRebew 2 роки тому
So the answer for AGM batteries is NO, right?
@daleg5553
@daleg5553 11 місяців тому
I have old batteries that don't have any fluid un them. Can I add distilled water and bring it back or is it history
@SweetProjectCars
@SweetProjectCars 10 місяців тому
Top them off within an inch of the tops with this amzn.to/3gb9Ni0 then get busy, you have all to gain and nothing to lose dale! Thank you for watching and asking, have a fantastic day and all the best on your project my friend. mad Mike the hammer SPC
@lukebray2192
@lukebray2192 2 роки тому
Can I use on old Lincoln welder for that?
@SweetProjectCars
@SweetProjectCars 2 роки тому
Our videos are very product/tool specific Luke, we take all the guess work out for our viewers as we have done all the trying, testing and failing to show everyone what we know works and is safe for both you and your batteries. Thanks for watching, have a great day. mad Mike the hammer SPC
@bradscottbutler
@bradscottbutler 2 роки тому
You are obviously talking about using an Arc welder. I happen to only have a flex welder. I'm now shopping for a Arc welder. Any suggestions?
@SweetProjectCars
@SweetProjectCars 2 роки тому
Hello Bradley, amzn.to/3yW4ihK or amzn.to/30k7YNg either will work great for this process. Thank you for watching and asking, have a fantastic day my friend. mad Mike the hammer SPC
@cybercatrdw
@cybercatrdw Рік тому
I did a battery with this method and had some success. I extracted some of the water from each cell and it is quite black. Does this black particulate reattach to the plates? Can I replace the water with new clean distilled water as you mentioned that the acid is not boiled away but only the water?
@SweetProjectCars
@SweetProjectCars Рік тому
Just top off the cells to within an inch of the top with this amzn.to/3gb9Ni0 before beginning this process, then again during the resting times as needed. It's not necessary to remove any of the water, just follow the instructions in the video to a T. Watch this ukposts.info/have/v-deo/jomln6RkhZWhlac.html for additional helpful information about this method. Thanks for watching Robert, have a great day and all the best on your project. mad Mike the hammer SPC
@cybercatrdw
@cybercatrdw Рік тому
@@SweetProjectCars Thank you for replying to my post. I watched the second video you show in your post. I will be trying these approaches and I love your channel.
@agguilarmetalwork4494
@agguilarmetalwork4494 Рік тому
Can this be done on a optima red cap battery?
@SweetProjectCars
@SweetProjectCars Рік тому
This works on wet-style batteries only. Thanks for watching and asking, have a great day. mad Mike the hammer SPC
@suegomez241
@suegomez241 Рік тому
You crack me up with that Julio Caesar Chavez …. Lol
@SweetProjectCars
@SweetProjectCars Рік тому
Hoolio is a jokester for sure, he keeps us all laughing! Thanks for watching Sue, hope you have a great day. mad Mike the hammer SPC
@joannatudor5125
@joannatudor5125 Рік тому
Are your using a am or DC welder ? Thanks
@SweetProjectCars
@SweetProjectCars Рік тому
Use this amzn.to/3yW4ihK and just a reminder, all of the products/tools we use in our videos can always be found in the ...MORE of the videos description, if you can't find it let us know and we will help you. Thanks for watching. mad Mike the hammer SPC
@elviefesta1903
@elviefesta1903 9 місяців тому
how to revive 8v deep cycle battery one cell not working? slow to bubble when charging with welder?
@SweetProjectCars
@SweetProjectCars 9 місяців тому
Do this video ukposts.info/have/v-deo/jomln6RkhZWhlac.html just cut the timelines in half for the 8v battery, but start out on the lowest setting, and gradually turn it up until you get a rapid boil on all cells. If you can't get that last cell to boil, your battery is toast my friend. Thanks for watching, have a great rest of your week. mad Mike
@elviefesta1903
@elviefesta1903 9 місяців тому
@@SweetProjectCars thank u ...my battery is toast!! ooh well
@egzecutore4732
@egzecutore4732 Рік тому
Would this method work for AGM batteries?
@SweetProjectCars
@SweetProjectCars Рік тому
This works on any lead acid battery, thanks for watching, have a great day. mad Mike the hammer SPC
Can you revive a dead car battery by inverting its polarity?
17:19
Garage 54
Переглядів 226 тис.
Новая технология! РАССЫПНОЙ ПОДШИПНИК
00:35
How did CatNap end up in Luca cartoon?🙀
00:16
LOL
Переглядів 5 млн
How to SUPER CLEAN your Engine Bay
21:58
ChrisFix
Переглядів 50 млн
This Stupid Thing Will Save You Thousands in Car Repairs
10:56
Scotty Kilmer
Переглядів 2 млн
Reviving Dead Batteries With A Stick Welder
19:05
Uncle Tony's Garage
Переглядів 1,5 млн
DEEP CYCLE BATTERY HACK?! Fix $400 battery for $20?! (Part 3)
21:54
Pure Living for Life
Переглядів 194 тис.
MAKE MAINTENANCE-FREE Batteries NEW AGAIN!
8:00
Sweet Project Cars
Переглядів 119 тис.
1752 A DIY Sand Battery - The Theory, Practice And Use
12:13
Robert Murray-Smith
Переглядів 361 тис.
How To Repair The NASTIEST Leather & Vinyl Seats....Back To PERFECT!
13:43
Sweet Project Cars
Переглядів 4,2 млн
Crazy Rally, special 🐕 vs 🚗 #rally #rallying #luckydog
0:13
Купил специальные чехол для машины #shorts
0:20