MWXNE 1200W 12V Inverter: amzn.to/468qzbC Oscilloscope: amzn.to/48gRVya TOPDON TC001 Hi-Res Thermal Imaging Camera: amzn.to/3pGiUBW Midea U Shaped 12000BTU AC Unit: amzn.to/43xiXPm ================ AFFILIATE DISCLOSURE: This channel may earn an affiliate commission if you purchase products through links I provide. ================ CONTACT: bradcagleyt@gmail.com Business/Collaboration only. Please do not contact me for for personal project help, or advice. ================ DISCLAIMER: These videos are documenting my own projects, and experiences. These projects, and activities can be dangerous. Do not try any of this at home, doing so will be at your own risk.

The remote battery may be one of those small 12v ones. A23 or A27.

My 2000w version has done its job through over a dozen power outages since last year in August. I`ve used it during five Louisiana heat emergency power outages since June with an Ampere Time battery for a small air conditioner.

Mine only shows voltage and other simple info but not wattage. I use a watt meter to monitor wattage and aprox battery capacity remaining and have had no issues. My 2000w version seems to be very efficient. I`ve used up to 3.4 kwh of the battery`s 3.8 kwh capacity but never drained it completely. Mine came with huge double cables and a remote wired display/controller that I`ve never used. I need a backup though just in case. I have limited solar and a 20amp plug-in charger. Having this stuff has repeatedly saved me from major suffering in the Louisiana heat while my relatives nearby who called me names for getting it had to evacuate to hotel rooms. And they didn`t even check on me after one of the worst storms with 80 mph winds even though I`m disabled, no car, and in a camper. My outlook on humans is at rock bottom at this point.

The Mighty Malinois! ❤

👍👌❤️🇨🇦, thanks for the review, still sticming with my SWI 3200 watt inverter

Thanks, good short and informative evaluation. I use a gopower 2kw pure sinewave inverter , first one lasted about ten years, replaced it with newer version, works well. I have renogy inverters for future use. Which brands do you see with the best quality and ruggedness? Thanks for taking time to answer

Did the efficiency calculations change when considering the watt-meters numbers? its being marketed at 92%. Load curves matter. from what I recall 50% load is best for efficiency peak.

I've been a subscriber for about three months and enjoy your content. In this video I'm more interested with the battery charger you were using. I would appreciate if you would post the link.

17:50 Can you please check and see how much power is being drawn when the inverter is off and no load connected to the USB? Just like to know how much power the USB circuit is drawing since you cannot turn off the power to the USB circuit. My AIMS 2K inverter USB is controlled by the power switch so when power switch is off everything is off. Great BTW.

HELP I purchased a MWXNE 1200 Watt Pure Sine Wave inverter to power my furnace which normally takes around 400 watts. When I attempt to run the furnace with the inverter, the motor kicks on but there is no heat and the furnace does not respond to the thermostat. So, I built an extension cord that only has the ground wire prong on both ends as suggested in another video. I plugged this cord into one of the outlets on the inverter and the other end into the ground connection at the furnace outlet. No change, the furnace kicks on, no heat, and after a few minutes it shuts down and does not respond to the thermostat. The inverter is connected to the battery in my Honda CRV using the supplied jumper cables. The inverter output voltage is 113v regardless if the CRV is running or not. With out the inverter the furnace works fine. Any ideas before I return this inverter to Amazon??

111 volts seems low for household voltage. Most are around 120 even though 110 was the original voltage, it should be 120 now. I would think an AC inverter would put out at least 155 or above even though 9 volts I guess isn't that much.

I have a 1500W inverter (Excelvan brand) Mine has output but if I plug in anything above that uses 600 watts it shuts itself down and the fault light comes on. No blown fuses or anything, If I cycle it off/on its good to go, until I try to plug in or turn something on that uses a lot of watts (i.e. like a small a 600 watt heater) Anyone have any idea what is going on? I used to be able to run things like a table saw or a small AC unit off of this thing before! Now I'm lucky to have a box fan and laptop working. Any ideas?

Odd angle OCD 🤯

Looks like an especially bad example of Chineesium, to me.