Portable Bluetooth Speaker Build (with DSP!)

День тому

👉 Build plans, wiring diagram and more: etsy.me/3Uc8Ux9
✅ Speaker available for purchase - etsy.me/3Up5tmJ
Parts (EU / US):
✅ Dayton Audio RS100-4 full-range driver (x2) - bit.ly/436nx7z / parts-express.sjv.io/PygqgN
Dayton Audio KAB-250v4 amplifier - bit.ly/4c1jTzQ / parts-express.sjv.io/anzZzo
Battery board - bit.ly/3uZqome / parts-express.sjv.io/VmKjKM
KPX programmer - bit.ly/49QLlyI / parts-express.sjv.io/B09Y9W
1" port (x2) - bit.ly/3wyaI9R / parts-express.sjv.io/QyAYaP
Optional cable package - bit.ly/4c1UKF9 / parts-express.sjv.io/ZQzezg
LED package - bit.ly/3T79IRR / parts-express.sjv.io/XYR5Rb
18650 battery cells (x3) - bit.ly/3J3KCNl / geni.us/LqDK
5.5x2.1mm charger - bit.ly/4a3j6wN / bit.ly/3w0YI0w / parts-express.sjv.io/9gD2Mj / geni.us/mbsMxh
Latching LED switch (19mm, 12V) - bit.ly/4a3nHPz / geni.us/Xz78Ut4
DC input jack 5.5x2.1mm - bit.ly/48I50j2 / parts-express.sjv.io/5gE5DL / bit.ly/3SFWFru / geni.us/Hbs3uD
Liquid tape - bit.ly/43ANz1N / geni.us/y5ph
Rubber feet - bit.ly/3IjqU2z / geni.us/E2PU4
M4x16 screws - bit.ly/3T6ljAs / geni.us/jt4Sq
Dayton Audio KABX Software Download - bit.ly/3OeGrCS
Tools:
✅ Creality 3D printer - geni.us/IuLA579
TS101 soldering iron - bit.ly/3HUzrI9 / geni.us/owyDm5G
Multimeter - bit.ly/3vS2aKG / geni.us/UmrhyYk
Wire stripper - bit.ly/3T1pVrO / geni.us/6epIs
Heat gun - bit.ly/3SyxaYX / geni.us/spT5M
Cordless drill - bit.ly/4bZg5PN / geni.us/A5AZi
Drill bit set - bit.ly/3S3i6zC / geni.us/ktAK1M
Jig saw - bit.ly/3uWmric / geni.us/D8GC
Orbital sander - bit.ly/3HBOC8O / geni.us/gHqu0W
Wood router - bit.ly/3I7Aplm / geni.us/6okRl
Router circle jig - bit.ly/3P5B75e / geni.us/JvCvO
Straight bit - bit.ly/43nXng8 / geni.us/bkAYwnC
Flush trim bit - bit.ly/43ggzfH / geni.us/bZRVci5
Round over bit (radius not less than 20mm) - bit.ly/4c39Av7 / geni.us/0MASr
Forstner bits - bit.ly/35snpjW / geni.us/F6it
Hole saw set - bit.ly/3YZU8tg / geni.us/hONP
Center punch - bit.ly/3xslc8u / geni.us/o5WBEwB
Helping hand - bit.ly/3B9mIgt / geni.us/Yyqyte
Thanks for watching!
- Donny
0:00 Intro
0:28 Making the enclosure
4:50 Veneering
9:35 Cutting the speaker holes
11:14 Sanding
12:13 Fixing the flaw
13:27 Finishing the enclosure
15:55 Speaker components
17:28 Wiring
19:20 Installing the components
26:05 DSP settings
27:43 Finished speaker
28:17 Sound test

КОМЕНТАРІ: 75

@ashystyle 4 місяці тому

You forgot to mention how much it would have cost. At least the parts. Well done as usual!

@DonnyTerek 3 місяці тому

Thank you! You can check the cost of parts in the description.

@maestrohun 20 днів тому

You don't want to know it, because otherwise you will buy a brand new factory built solution, because of the price/perf.

@umbrellacorp. 3 місяці тому

And if you don't have woodworking machines you're DOOMED!!!... 😂

@DonnyTerek 3 місяці тому

Unless you're aiming for the same result, I have to agree 😄

@mjb2496 2 місяці тому

You can do it bro

@komradekoala5648 Місяць тому

Even without some of these machines, a saw and a drill will definitely get you a nice enclosure! They sell kits online with everything you need though

@user-iy8oc7dq5t 3 місяці тому

As always, a masterpiece!

@DonnyTerek 3 місяці тому

Thank you!

@dannyverhamme7970 4 місяці тому

This is a very enjoyable video to watch! Thanks. 😀

@DonnyTerek 3 місяці тому

Thanks for watching!

@diogoandrade4772 2 місяці тому

Your work is incredible! I haven't seen anything like it! I would be very happy to win one of these! 😊

@shahintalukdar9829 4 місяці тому

Good work but the batteries should tighten with cable tie or glue gun to prevent come out from slot when accidentally speaker face any falling issue from any high surface to ground.

@DonnyTerek 3 місяці тому

Thank you! The batteries are held in very tight. You would most likely break the speaker first before the batteries get loose.

@arshaax6968 4 місяці тому

Good job man, I enjoyed it very much👍🏻

@DonnyTerek 3 місяці тому

Thank you a lot!

@bladE290879 3 місяці тому

Nice work. Using dedicated programming connector back in the speaker (e.g M12) could make a sense in case you ever need to reconfigure the speaker.

@DonnyTerek 3 місяці тому

Thank you! That's a great idea!

@edgarchansin5617 4 місяці тому

Suelo ver tus trabajos y me parece increíble...el detalle y el acabado son muy bueno....éxitos 🙌

@DonnyTerek 3 місяці тому

Thank you!

@steveroberts 4 місяці тому

Nice build and explanation

@DonnyTerek 3 місяці тому

Thank you kindly.

@xeroname 3 місяці тому

Nice video and clean, neat speaker! I've always wondered how every diyers make smooth surface finish of wooden enclosure, and today I solved this question thanks to your video. Also surprised about the solution at 12:55 which despite non-curable mistake in normal situation! Thanks to your video and hope you have a nice day 😁

@DonnyTerek 3 місяці тому

Thank you so much! Yes, and even that finish is not the smoothest 😄 Thanks for watching and I'll hope you stay tuned for other projects!

@endall39 4 місяці тому

Really nice! There are inexpensive calibrated measurement mics out there. If you’re intending to set the DSP once, I’d want to see the pink noise response and use it to guide you to a base curve. Then tune to taste.

@DonnyTerek 3 місяці тому

Thank you! Have to agree, I should probably get a measurement mic for my next builds.

@_mysilentblue2227 4 місяці тому

I like your spray can stand.

@DonnyTerek 3 місяці тому

Thanks! 😄

@user-co4lb5yz1x 2 місяці тому

Все отлично! Молодец за такой проект. Но я бы сделал заместо фазоинверторов один большой пассивный резонатор внизу. Получилась бы система 2.1, и отдача на басах существенно бы возросла. Чтобы отсеять кросканальные акустические наводки в таком случае, внутреннее пространство лучше заполнить синтепоном.

@st170ish 4 місяці тому

Nicely done Donny, any reason you didnt use some more veneer to fix the corner?

@DonnyTerek 3 місяці тому

Thank you! It would be a quite tedious job to glue a piece that small and probably wouldn't look any better than it is right now.

@marzooperinhoo9011 4 місяці тому

Perfect video just a question, there are no crossover between drivers and amp? Thx for the answer

@hansmeiyer831 4 місяці тому

These are full range speakers, no need for splitting the signal to high frequency and low frequency components.

@bastianrivero 19 днів тому

Perfection

@rezvanfar 3 місяці тому

youre an artist

@DonnyTerek 3 місяці тому

Thank you!

@daa2622 Місяць тому

i agree

@Simone-qr6mq 2 місяці тому

Do you have any suggestions about a cheap, non amplified DSP for diy speakers?

@meany2 3 місяці тому

A lot wait for your video❤❤❤❤❤❤

@DonnyTerek 3 місяці тому

Hope it was worth it!

@meany2 3 місяці тому

@@DonnyTerek yes superb💌💌💌💌💌

@johnraffyvito2790 2 місяці тому

It would be nice looking if you use a torx screw

@millenniumrun9995 4 місяці тому

Excellent work! Just a suggestion: Lining the inside with open cell foam and filling the open space with poly fill really cleans up the sound. Just don't obstruct the port. Great content man.

@DonnyTerek 3 місяці тому

Thank you for the kind comment and tip!

@millenniumrun9995 3 місяці тому

@@DonnyTerek No problem dude. Keep up the good work. You have some of my favorite DIY audio content. I'd love to see a high end build some day. Try some Scanspeak drivers and you won't be disappointed.

@DonnyTerek 3 місяці тому

@@millenniumrun9995 Much appreciated. Will definitely be trying a high end build in the near future to replace the Amigas even though they are quite amazing for the price.

@daa2622 Місяць тому

i love how it looks, but it really nags me knowing the amount of sound diffusion around the corners. it causes hills and valleys in the frequency response. but still, a great build for an MDF speaker

@VINAYKUMAR-wl4gk 4 місяці тому

After a long time 😊

@manadoinitialdj8795 2 місяці тому

nice work Sir❤❤, but how you make round corner? im really interesting😊

@Ace10929 2 місяці тому

Oh I can't find my last comment. Small question, Is the dc power connector included in the dayton audio amp board? (when you buy it) to charge the extended batteries

@DonnyTerek 2 місяці тому

You have to buy the DC connector separately, I have placed the links in the description.

@fouzaialaa7962 Місяць тому

add some rubber bands or some scotch tape around the battery's and the battery holder so when the speaker inevitably falls from the table or something the battery's dont pop off the holder

@ejfrederico 3 місяці тому

Perfeito

@gauravbhilare98 2 місяці тому

Marhsall who? We need this speaker man, in INR it costs 2x less than Marshall to build this !!

@ariangeroy6035 Місяць тому

can you make a simple and cheap speaker

@Gabriell17b 4 місяці тому

Preço final?

@wolfairxpdc4384 4 місяці тому

👍👍👍👍👍🔥🔥🔥

@peterukw 2 місяці тому

I have paid and down loaded your plans but you have missed out the drawing for the back panel, can you add it please.

@Vinz3ntR 3 місяці тому

I always thought veneer was pre glued and only heat is needed to fix it to the wood

@DonnyTerek 3 місяці тому

That would most likely be synthetic veneer, probably PVC that only requires heat to be glued.

@yokohamalover-mc2wy 2 місяці тому

Wao～Nice　Sounds Good ！！！

@davidlee3203 4 місяці тому

But how was there no line from the two corners meeting around the edges of the speaker box? Tell me im really confused how there wasnt any.

@abramhunter6249 3 місяці тому

They are still there. It is hard to see with a nice sanding job and partially covered in glue.

@DonnyTerek 3 місяці тому

There is a line, down at the bottom.

@TYAGI_MOTO_VLOGS_786 4 місяці тому

Dimensions are not shown in the description

@DonnyTerek 3 місяці тому

Just uploaded the plans, please check.

@mikhail_gritsay 4 місяці тому

Нужно было войлоком изнутри проклеить, убирает гул и делает звук приятнее

@champakkharshiing9211 3 місяці тому

Hi sir good evening

@ugochukwuokafor3764 3 місяці тому

You haven't put the free plans yet

@DonnyTerek 3 місяці тому

Just uploaded the plans, please check.

@82cfmedina 3 місяці тому

Necesito esto en españoooooool 😫

@hercules7136 Місяць тому

I would like to buy from Turkey please support

@ankamanirudh8837 4 місяці тому

No bass plain

@parthaprothimsarker5844 4 місяці тому

266$

@DiamondDog_ 3 місяці тому

🤣🤣🤣