Great to see these videos though, being informative to help consumers know the difference between a reputable electrician and someone who cares about how it functions and works!

I've been in the automotive trade for around 40 year sand have forgotten the amount of times people have said that they have read on forums or the internet or from a mate down the pub that their specific job needing doing is easy,usually without them or their mate having a clue about what they are talking about. I used to argue the toss every time,now I just say,"yep,maybe so but its still that price if you want me to do it,if not get your mate to do it,it's easy!"

Cracking job you've made of that board,one of the neatest I've seen,it certainly makes a difference cutting down those neutrals as it's less cluttered at the back,great content

Good lil tip if you haven't got that mirror to check the busbar has gone into the holes correctly is to use the busbar itself to push the screws on the bottom of the breakers back

That is a nice New installation, shame you didn't do ours, we had to pay a proper Electrician firm to come in our New build, strip out the consumer unit check everything and rewire it properly because in their words looked like a Friday afternoon installation, other houses on the 6 house estate were just as bad, now the builder has had to pick up the bill for all 6 rewires, including plaster repairs and decorating, we are all safe now.

One of the best CU vids mate. Top quality and super neat. Hats off to you!

this might help mate, when tightening the busbar undo all the bottom terminals fully put the busbar in then push it away from you towards the back of the board then tighten one by one just until they slightly pull the busbar forward then onto the next then retorque up then use the mirror. nice vid once again mate

Nice clean job as per usual from you mate... If that cu was 50 mm taller it would be ok for fitting rcbo's other than that it looks like a decent bit of kit..... 👍

A good space to work in always helps when it comes to installing CCU's Makes it so much simpler

Embarrassingly neater than mine. The heatshrink sleeving is cool too & so is the slicing tool for the Inner of the swa. Also the mirror tool is cool too, i use an old vanity mirror that i borrowed from an elderly customer about 25 yrs ago ( approx 2" × 1") i must remember to let her have it back 1 day. As for All tails, i always do it by hand , give em a good twist and wriggle then i get another full turn... repeat etc, as i have in my time seen rather a lot of tails fall out of meters & cut outs where the elec company rarely do the tight enough.

I’m a subscriber from the US and an electrical contractor myself. These are so vastly different from the American counterparts! I am a fan of your videos and I watch to learn how different but similar the installs are. Keep up the good work my friend!

your videos very important for my future because I am going to sturdy something about wiring works. God bless you dude..!!

Cracking bit of information and guidance on how to do DB. Looks like Schneider haven’t considered the height of the board compared to them RCBO’s.

Good vid mate - good idea with the mirror checking the bottom busbar connections👍

Has to be one of the best and most entertaining CU videos on here. Cheers Ryan 👌🏻

Representing from UK Power Networks official owners of Southern Electric. It's nice to see electricians who remember us by name :)

Sparky from US, so interesting to see the different equipment and standards. Keep up the good work.

well done good video good neat job i think maybe next time wire in the SPD some people struggle with this the first time they come across it 10 out of 10

Great video, thanks. You mentioned you aren't a fan of cable ties so I wondered how you got the rcbo neutral leads so neat and tight up the top? Cheers

Love the Schneider boards, but find the RCBOs don’t leave much space at the top. Would love if Schneider will bring out some compact ones! Neat job guys 😊

Irish sparky, we can't fit consumer units under stairs fite hazard, our regs don't allow us . Min height new fuseboard new project 1400 mm to bottom but we use double stack boards , 2150mm to top highest mcb/rcbo

Good video!!! I was always wondering why the recruitment agencies always advertise commercial and domestic electrician, now I understand why after seeing this gentleman terminating the SWA gland! Overall very good video!

The Fusebox consumer units can be purchased with miniature RCBO's to give you loads of space at the top. Also they don't have the functional earth wire either. The Schneider is probably better quality but I went for the Fusebox one for my house as alot of the good youtube domestic sparks seem to swear by them. I'm an industrial electrical controls & software enginneer in a car factory so spent alot of time deciding on this one. Nice neat job 👍

I hope you remembered to earth the SWA cable armoured shield.

Hi, nice work there, wanted to know, what gasket did you use on the cable inlet on the back of the CU?

Put the Earth in the left hole (you had enough slack) have routed it along the bottom and up the side of the DIN rail and sorts one issue, perhaps buy single phase cable next time (you do people use the WRONG cable all the time?) and possibly start using piranha earth nuts to tidy things up.... But great video, Schneider lost it IMHO when they dropped the Isobar stuff, full size RCBOs with functional earths are just SO last week, I wouldn't use and un-branded (FuseBOX) CU as I simply would get away with is, but you now have a good choice of miniature, type A, no-earth-wire RCBOs out there and Schneider need to catch up!

I would run a earth lead off the SWA locknut too. You could argue it’s earthed through the metal consumer unit box but belt and braces? I like the lock nuts with the teeth that cut into the paint when tightened. They also have a bolt for attaching a earth lead 👍🏻

Not a fan of them boards with rcbos. Not much room above like you’ve said. With a 25mm earth you could’ve made it easier for yourself putting in the far left terminal perhaps. Good job as always

I have done hundreds of swa glands and at the end of my apprenticeship I could do one in 3 mins blindfolded! You can take off multiple wires at a time when scored (I always use a junior hacksaw to get a deeper score to make this easier and faster). Plus, when you wind out the galvo wires always do them in the direction of the wind as they lay in the cable as this will prevent the ragged dispersion you got when you went the wrong way. A few tips to make this easier I hope. Liked the video. Nice work. When you come back will you seal the entry with intumescent foam into the cavity?

nice tools! expensive but useful, i loved that milwaukee

New to your channel. You’ve done a great job on that consumer unit & thanks for the great tip with the mirror checking the busbar connections. I’ve been using my phone camera with the light & struggling to do so before. All the best 👍🏻

Job well done 👍🏻

Nice one board look the business now it’s all wired up ,I know the wire was a little long but Better thanks being to short. Cheers

Hi Mate, can you supply a link for the armoured tools you used also the light. Brilliant video 👍

It is easy! Use the plastic ones and get customer to install 90 min rated enclosure

I’m just coming to the end of my electrical apprenticeship and about to do my AM2S exam is there any chance you could do a video on testing? Love your videos and tiktoks always watching 💪🏼

LOve the mirror ! very neat trick .

Nice job! (another sparky using grips the wrong way around lol)😉

Great video 👍🏻 weird question, what music you tend to listen to when youre doing your consumer units?

Hey! The most important bit I needed to know you left it out. How do you measure where to cut the SWA back to for a perfect fit with the gland/board

Good job , I’d would of filed the paint of the consumer unit before fitting the SWA to get a good earth connection on armour

What a good video, great quality and good aesthetics in your work, I have learned much more about how you work in the UK. Greetings from Arica (Chile) (sorry for my bad english, I'm using google translator)

really nice work. do you leave the busbar like that, or trim it down?

Nice and tidy job …

Neat board, will the banjo be done later?

Comes from back in the day, wiring looms and harnesses electronics old school.

Hi mate. Nice one. Just starting a side hustle doing minor works. What make is your crimping tool. Looking for one that will last and do up to 16mm for when I get more qualified and fit the big stuff =) cheers.

How do you keep your consumer units so neat!🤩

Hello mate. Just came across your channel. Instant subscriber. Really enjoyed watching the video and learning. Currently working my way through the NVQ and planning on getting qualified in 2024. How do you like the Knipex crimping tool? Is it really worth the premium price? Thanks

Looks good nice install. Not so sure about the plasterboard fixings though

Looks a nice board to fit, massive let down on the fly leads tho, big up I enjoyed that 👏

Good job 👍

You live the busbar just there with free prongs hanging out beside the RCDs?

Might be a silly question so I apologise before hand, but how do you know what to mark up the cables as if nothing is fitted in yet?

Top job!

if i can see well you forgot to connect the neutral cable from the bottom side of the main breaker back to the neutral bar! please correct me if I'm wrong. with respect Manos!

Nice dude. Main Earth would be good over the other side of the bar out of the way of any circuit protection.

Exellent job sir

Good Job Dav. I'm from Srilanka.

Really enjoyed this video.

Good vid. But it’s a busbar. If it buzzes you have issues.

Very beautiful work. Very clear and completely different from Germany. Here most of the subdistributions are three-phase. I would have found one thing even better: If the consumer unit has to be replaced in a few years, it can be a problem that all the cables are cut to size. Perhaps in this case it would have been better to leave a few handbreadths of cable as a loop tucked into the drywall instead of cutting off all the cables.

My brother is a sparkie and done a bit of work on my house and he shows me all the bits because I have a genuine interest in electronics. Honestly, I would not want to install one of these. Thankfully, the law does not permit my stupid ass from doing it! I’ll stick to doing bulbs and switches!

personally would have used toggle fixings instead of plasterboard fixings, need to get myself a ferrule crimper. good job

Did that grommet strip come with the board?

Do Schneider do a miniature/compact RCBO? They make it a lot easier on Wylex and Fusebox boards that I've used.

If a customer does not have his kitchen built, can you do a first and 2nd fix? I mean, add sockets without plastering and leave boxes loose off wall for eye level oven and integrated fridge for customers to bolt to kitchen. he would have the appliances so you know the loads Or, do you have to return to see oven bolted in secure etc to allow sign off of certificate? Just trying to avoid two visits cost if that's possible?

Mr Davis loving your work and videos! one quick question could you tell the the name and model number of the tool you're using to strip the twin and earth cables please? thanks in advance.

Enjoyed the video as im still learning. Just a question....Did you cut down the excess on the busbar afterwards?

mudah bagi pakar nya bro,buat orang awam mungkin susah,,,salam dari indonesia

Really nice install but a grommet strip on the jagged punch out on the back would have been good to see 👀

Hey man, you said you aren't a fan of cable ties in consumer units and I'm just curious why? Great video though

Looks like a new build, how have you got around the Rcbo switch heights? Definitely aren’t between 1350-1450

I would have drilled and bolted the earth ring / banjo before fitting the switch gear to avoid any accidental damage but otherwise good vlog

Nice job, however did I see no grommet strip around the entry in the back? Looked like it had some sharp points

Looking for some advice, I have 3 appliances each allegedly consuming 3050 at maximum capacity, but the wires and my main feed to the consumer unit is getting so hot. I deliberately upgraded my consumer unit so it could handle these appliances. I installed the outlet (Specifically for these appliances) using Prysmian 10mm2 twin and earth, wired to a 50-amp breaker, then installed ANOTHER Prysmian 10mm2 twin and earth, wired to a another 50-amp breaker so there are now 2, one for two lower end of the consumer unit and the other for the higher end. Furthermore, I also have two BG 80A 30mA 2 Residual current device (RCD) installed on the consumer unit and the main feed that powers the consumer unit has a fuse of 100amps. These appliances are in a container where I linked each outlet to one another so they can draw power from the first one (again, each has its own 50-amp breaker at the opposing side of the consumer unit, one for the upper side and one for the lower side), not sure if that is causing resistance as I even have the powercables with 13amp fuses to power those appliances, but since there is a 50amp breaker for each outlet, I’m still confused.

What cable strippers are you using mate?

Good job

Can you send some link for them striping cable tools ? Thanks

how come the cables arent marked with the correct colour from the start? like blue and PE?

I like the install but wouldn't use those schneider DBs, too clunky with the functional earth lead and the neutral being excessively long.

Just wondering about the height off the ground seems a bit low , PS I'm not a sparks 👍🇮🇪☘️👋

The terminal bar can be reversed so the big cable comes in at the left

Well done, don’t think I’ve commented before on your vids so I’m giving you the privilege of a supersparks comment.

What wire strippers is that your using on the t+e, they look mint

Suggestion, mark each terminal shroud as you torque it.

Personally I would of used a 25mm split con instead of the SWA. A lot easier to fit, lighter, more flexible, can just use a stuffing gland. When its visible, run a bit of 25mm conduit to give it a little protection. Non the less, great install.

Made making that armoured look hard

The decorator did a grand job of masking the armoured cable

I'd put the earthning on the left side, so there'd be more space to do the job.

if the earth is too thick for 1 terminal I split it and connect using two terminals. And why you didn't use 1st terminal on the left to get that 25mm of the way.

It's the wrong rcbos 10 KA not 6 KA they are for the big 3phase boards where you need the length of the cables your dist board is very neat

No banjo from the gland?

Hi an Aussie electrician here, just wondering why is it so low, is that a law or some other reason. Thanks

Fireborard? Fire putty to seal the holes? Don’t know if you have to but we normally do

great video are them wire strippers knipex have you a product code cheers

I'm from UK and a certified electrician. Also many other skills. But I have to let this lose my friend those self drilling plugs you are useing are best of drilled straight into dry wall ( plaster board ) you don't need a pilot holl they more stronger if you use a pz2 and drill them straight into the wall. Ps the plastic ones are shite lol go for the metal ones they also have a better head and thread 😉

All good, other than drywall screws I would use drywall compression fixings as CU might stay there for a couple of decades and knock off for cable entry can't see anything protection from sharp edges!

I'm English but moved to Germany and did my qwals as an electrician here, watching out of curiosity how it is back home and there a quite a lot of differences from the stuff done here despite similar SOPs. Can't say I've even seen an armoured cable here and was curious there is no better way of terminating the armoured splices. Also that the consumer unit has 1 row as standard. Any patient english electrician around to discuss it ? Plus I never see a mains switch in consumer units in the UK, is that just down to costs ?

Nice neat job how was the armour earthed please