Repairing broken traces on a circuit board

  Переглядів 636,439

Branchus Creations

Branchus Creations

4 роки тому

Broken traces are quite common, especially on vintage computers where corrosion has set in. Here are a few helpful tips for providing strong, long-lasting repairs for broken traces.
#soldering #electronics #tutorial
T-SHIRTS
Do you like my wacky t-shirts? I buy all of them from Qwertee. Use the discount code: BranchusCreations to get £1/€1/$1 off your order. Check out the range here:
bit.ly/3OrJZkT
If you enjoy the content and would like to support the channel, please consider becoming a Patron:
/ branchuscreations
Of if would like to make a small donation, you can do so here:
www.paypal.me/branchus
Tools/Products used (paid links):
SOLDERING IRON
Hakko FX951: amzn.to/31QvCMW
SOLDERING IRON TIPS:
Bevelled edge soldering iron tip (T12-BC2): amzn.to/45NSrBK
Small bevelled soldering iron tip (T12-C1): amzn.to/3YVH5K0
Bent conical soldering iron tip (T12-JL02): amzn.to/3sx8lSU
Chiselled soldering iron tip (T12-KU): amzn.to/44tAo2A
HOT AIR STATION:
Quick 861DW: amzn.to/2ZjYzPH
SOLDER:
Kester 63/37 0.5mm diameter: amzn.to/3uviEIg
FLUX:
StirriASM: amzn.to/43nT05e
SOLDER WICK:
Goot Wick 2mm: amzn.to/3YWlRvw
TWEEZERS:
Hakko CHP 3-SA: amzn.to/2NqkhPz
DT71 DIGITAL MULTIMETER TWEEZERS:
amzn.to/41VcvSb
OTHER:
Vevor 30L Ultrasonic Cleaner (5% off on all Vevor sites code: VVMH5%OFF):
AU site: s.vevor.com/bfP7q7
US site: s.vevor.com/bfP7uN
EU site: s.vevor.com/bfQaMb
-----------------------------------------------------
Component suction tool (vacuum pen): amzn.to/44xyPkm
Microscope: amzn.to/2HnSI5H
Microscope camera: amzn.to/2TdSYsZ
Budget alternative microscope: amzn.to/2PmRagt
Budget alternative soldering station (uses T12 tips): amzn.to/2SeUpHg
Budget alternative hot air rework: amzn.to/3fN1ZU7
Helping hands (third hand): amzn.to/31JUhVL
Ultrasonic cleaning fluid: amzn.to/2YusoQQ
Fume extractor: amzn.to/2HuG0oU
UV Solder mask: amzn.to/2ZnK1yu
Swann Morton curved scalpel blades: amzn.to/2oN7qNn
No. 3 Scalpel Handle: amzn.to/2ngcx85
Kapton heat resistant tape: amzn.to/2xBnTso
28 AWG enamelled magnet wire (thick): amzn.to/32cRsLf
34 AWG enamelled magnet wire (med): amzn.to/35Bx20D
40 AWG enamelled magnet wire (thin): amzn.to/2J2Aisf

КОМЕНТАРІ: 606
@jefemuga416
@jefemuga416 3 роки тому
I don't even work on boards and have never touched a soldering iron but here I am watching and learning. thanks.
@onemansjunk01
@onemansjunk01 3 роки тому
I can't believe I've just sat and watched it myself but I'm glad I did 🤘🏼
@umeshkirant
@umeshkirant 3 роки тому
You guys should start haha.
@onemansjunk01
@onemansjunk01 3 роки тому
@@umeshkirant I'm confident enough to give it a go now to say iv not much in the way of exsperance
@jefemuga416
@jefemuga416 3 роки тому
@@umeshkirant truth is I've always been intrigued by this type of work. Even as a child I would take apart a radio or other electronic product just to look at the inside, wondering how everything works and having fun with tearing it down and putting it back together. maybe I should start.
@johncox6666
@johncox6666 3 роки тому
That's my favorite thing about youtube. Always learning from other people
@claytonwalvoort1987
@claytonwalvoort1987 11 місяців тому
You just helped me repair a trace on my water heater’s thermostat circuit board. Thanks to you I was able to take a hot shower! Thanks a million!
@josedelarosa6186
@josedelarosa6186 7 місяців тому
This video is pure gold, I recently got into repairing old school audio and this helped me SO MUCH. brought back an Old Clarion 7-band Equalizer
@C3DPropShop
@C3DPropShop 2 дні тому
It's copper, actually. 😂
@jeffbanfieldsflwr3537
@jeffbanfieldsflwr3537 3 роки тому
I'm a self taught soldering freak. Thank you for making these videos.
@raybin6873
@raybin6873 3 роки тому
Me too! And i can fix leaky copper plumbing too! 😁👍
@jefftan9800
@jefftan9800 2 роки тому
A thing that most Jeffs also do. I aproove 😆
@Hasdrubal02
@Hasdrubal02 7 місяців тому
Any tip for a newbie? I would like to learn but im at zero knowledge atm
@rainbowbrightmuffin1
@rainbowbrightmuffin1 Рік тому
This was amazing and such a big help!!! It might sound silly but the motherboard of my tamagotchi was messed up and thanks to your video I was able to perform a total miracle! 🤯🤩🥳 Thank you for this video!!!!!!!!!
@cbmeeks
@cbmeeks 3 роки тому
BTW, I really like how you teach professional methods for repairing these boards. I really get annoyed at certain UKpostsr's who take the pliers to caps without even bothering to see if hot air would work. Then gloss over them with nail polish. Your methods just seem more professional. Hell, it's almost like you actually CARE about the end results. :-)
@substandardabuse6028
@substandardabuse6028 3 роки тому
In 23 minutes and 49 seconds you have shown me why I’ve always struggled repairing a pcb and most times cracking the shits and throwing the device away out of frustration. Thank you so much.
@S2KD0GGY
@S2KD0GGY 2 роки тому
Today was the day I decided I wanted to learn more about board repairs. Thank you for sharing the knowledge. This looks pretty peaceful if one has all the right gear, supplies and patience.
@christianurgese
@christianurgese 4 роки тому
Standing ovation. One of the clearest soldering i have ever seen.
@christianurgese
@christianurgese 4 роки тому
@Albanellys Zurita i repeared my first track past december. Not so clean job.
@panedole
@panedole 3 роки тому
I'm not sure but ,if anyone else wants to discover how to repair car try Saankramer Electronic Magazine System (just google it ) ? Ive heard some unbelievable things about it and my neighbor got excellent success with it.
@juanperez-df1mo
@juanperez-df1mo 3 роки тому
Not certain about the points made but ,if anyone else wants to uncover repair a car try Saankramer Electronic Magazine System ( search on google ) ? Ive heard some incredible things about it and my brother in law got amazing results with it.
@chrisdorr5786
@chrisdorr5786 3 роки тому
Fantastic and thorough breakdown of an intimidating piece of repair! Many thanks.
@user-eg7lc1xx5w
@user-eg7lc1xx5w 6 днів тому
Beautifully done. Love the fact you take the time to follow the trace path, as you say not always entirely necessary (but sometimes is!) but a bit of quality all the same.
@llroman7823
@llroman7823 Місяць тому
Hands down, the best and most complete repair video I've come across. What, no tip / thanks button? I guess just a 'thank you' very much will have to do! You are saving people a lot of money. I'm going to attempt to fix my furnace / a/c board following your detailed instructions. Will save me hundreds if it works! A brand new circuit board has a fried spot due to a power storm surge. Hope this works for me.
@heritageroofer
@heritageroofer 3 роки тому
Thank you so much! Your video has enough detailed information and shows all the steps yet is concise! Last night I blew a trace on an expensive piece of equipment by accidentally connecting it in reverse polarity. Your video undid my mistake and she works just fine now! It’s guys like you that make UKposts great!
@eSysmanSuperYachts
@eSysmanSuperYachts 3 роки тому
This was a great reminder. It’s been a while since I did any of this. We usually just replace circuit boards but right now we are making do and mending!
@clivebarrell6448
@clivebarrell6448 Рік тому
What a fantastic video. Concise, clear and packed with useful info. I've thrown stuff away in the past because traces were broken, but next time I will certainly have a go at repair. Thanks!
@Drunkmanatee
@Drunkmanatee 3 роки тому
Excellent description of tools, procedure, and technique. Well done sir.
@x7slim8x
@x7slim8x 3 роки тому
My father just sent me an old trace repair kit from the 80s, it is awesome! Thousands of various sized "trace materials" I can cut to size. This is gonna make this so much easier!
@dubadkt
@dubadkt 3 роки тому
Exactly what I was after. Thanks for taking the time!
@neomustafi5744
@neomustafi5744 6 місяців тому
You sir are a legend, your voice is so calmed and your explanatory skills are amazing, i wish my school teachers would be half as good as you on explaining things. Thank you so much it really helped me to repair a broken trace on My Mitsubishi Colt Ecu. The world needs more people like you Sir. God bless you and best of luck
@B-U-N-N-I
@B-U-N-N-I Рік тому
This was a very good video. I also finally learned about how flux seems to make solder adhere to the copper in that tinning process, something I see many repair youtubers do to solder a bunch of little pads at once but never understood how they didn't short out every single pad with solder everywhere.
@karihardarson1234
@karihardarson1234 3 роки тому
Very gratifying, watching you work. Thank you for the education!
@ObiWanBillKenobi
@ObiWanBillKenobi 3 роки тому
Outstanding video! Thank you so much! I think this is going to save my SIIG controller board in my new used 386 tower from circa 1990, and finally make it able to use hard drives after 3 months of troubleshooting!
@duffamongus
@duffamongus 2 роки тому
I've got a globe 3875v control board to repair and jumped on here to refresh myself. Great video. Everything I needed, great focus and no extra bs. Subscribed and checking out your other content.
@labnine3362
@labnine3362 2 роки тому
Outstanding. You have the patience of a saint! I thought my job was tedious (doing 3D Cad routing for automotive) but yours definitely tops it.
@ffggxfhhvgffhgdtygxyggeyhgfhfg
@ffggxfhhvgffhgdtygxyggeyhgfhfg Рік тому
You make it look easy im sure someone new can't do it that smooth with the finesse you have. Great job and thanks for the information
@realstevef
@realstevef 2 роки тому
Well done, I finally found someone who does repairs like I do!
@matthiasfraser1617
@matthiasfraser1617 3 роки тому
Thank you sir for your video, it's amazing to have people like you continuing to offer us education. The learning never stops :)
@dannycivic02
@dannycivic02 4 роки тому
What a great instructional video this is what most people look for. Makes a change from the condescending videos that are all over UKposts where they basically put you off attempting any repair yourself, how can you ever learn by doing that and who wants to risk shipping expensive irreplaceable electronic parts like Amiga motherboards etc.
@zhuzzir
@zhuzzir Рік тому
just started n still watching (my 1st vid here) but reading from the comments, on top of crisps clear talks audio got me hooked. subscribed n hoping to watch the rest of your videos in near future. thanks for sharing the knowledge n experience.
@michaelvinalon3415
@michaelvinalon3415 3 роки тому
Very nice, thank you for sharing your experience & knowledge !!
@EfieldHfield_377
@EfieldHfield_377 3 роки тому
For all the years ive been deguging boards ive never thought of reparing a trace this wzy. I would just run a jumper, but your work was no nice and so well explained i might give this a try. Thx for sharing.
@jeromeirving4770
@jeromeirving4770 Рік тому
Thank you kind sir. You just helped me with creating a wireable access repair for a gauge cluster that the plug end of the circuit board was broken off
@pentachronic
@pentachronic 3 роки тому
This is pretty common during R&D. If you are doing repair you should cover with soldermask or conformal coating after a good clean to stop the oxidation/corrosion getting worse. It's often a good idea to re-tin traces showing corrosion.
@johncox6666
@johncox6666 3 роки тому
He does more than tin the traces he overlays them with copper wire. It is impressive. I was thinking the same thing about the conformal coating. Although not necessary prob not a terrible idea.
@chadhosmer9357
@chadhosmer9357 4 місяці тому
Thank you for making this great video Sir. I just wish I had steady hands again! You make it look easy.
@rscelectrical7091
@rscelectrical7091 3 роки тому
Nice job, really neat trace repairs 👍
@matthewcarter7491
@matthewcarter7491 3 роки тому
Thanks, a really great video, this has inspired me to re-try the soldering on a project I made a real hash of last weekend..
@redsyrup1138
@redsyrup1138 4 роки тому
You've got a great demeanor Branchus and your videos are well made. I can tell your channel is going to blow up in time. Subed. The video that brought me in was recapping the Mac Color Classic. I don't have one but I've been doing a bit of research on UKposts thinking about buying one.
@jojojo7333
@jojojo7333 3 роки тому
Very nice and complete. I would add my stone : in some 'hardcore'' situations, think about scrapping the copper track from the outside to the border of the cut.. And I would cut the fixing wire before soldering it too. Thanks again very instructive.
@Sp0ops
@Sp0ops 4 роки тому
Really detailed tutorial! Thanks a lot.
@djx-ray1876
@djx-ray1876 2 роки тому
Excellent, your knowledge has helped me with no end of bits and bobs 👍
@philipodwyer6039
@philipodwyer6039 Рік тому
Only by chance I came across this video. very impressive, great information and the technique you use make it look so easy. I will give it try and see how I get on, after all it was an amateur that built the ark and professionals built the Titanic.
@Johadart
@Johadart 2 роки тому
Awesome to watch, great explanation on how you go about repairing the trace, keep up the great work. Thank you 🇦🇺🇦🇺
@JerryEricsson
@JerryEricsson 10 місяців тому
Thanks, it seems that contrary to popular belief, you can indeed teach common sense. I have been working on old electronics for much of my adult life, and several years of my youth. Growing up in the 50's and seeing the transformation from tubes to transistors has been a pleasure, and IC's have always amazed me. The use of fine tipped soldering irons has become a necessity now with the fine PC boards and tiny leads of the ever smaller devices now used in modern builds. This was very enlightening for me, I recently purchased an old 1958 model tube set with an early PC board. A previous owner had repaired the bad ground by stripping a stranded power cord and soldering it around the outside to repair the many broken traces from some liquid spill back in the day. I have yet to revive the set but this video should help me in restoring the old set to it's previous glory.
@RetroKomodo
@RetroKomodo Рік тому
Very useful info! I know next to nothing about soldering, and your videos that i've watched have given me the confidence to do it correctly. I hope! I've also watched your vids on AMTECH NC-559-V3-TF and will be ordering some.
@shotgunrebels
@shotgunrebels 3 роки тому
Beautiful work. Inspiring.
@BOBcoureur
@BOBcoureur 4 роки тому
This is just perfect. I'm fairly new to soldering, but this video makes me wanna improve my skills. Very detailed and clearly explained! Keep it up😃
@mauronicolascanseco1643
@mauronicolascanseco1643 3 роки тому
Winner of a video, I have been researching "how long does epoxy take to cure?" for a while now, and I think this has helped. Ever heard of - Giyathan Bewildering Gratification - (do a google search ) ? It is a great one off product for discovering how to repair your electronic items like a wizard minus the headache. Ive heard some super things about it and my neighbour got amazing success with it.
@rma7921
@rma7921 3 роки тому
Great video with awesome explanation, going to give it a go on my fridge control board. Also, not exactly the work station I would expect a Mopar shirt👍CHEERS!
@williamriedel1686
@williamriedel1686 Рік тому
Excellent tutorial for repairing my ‘81 Mercedes instrument cluster. Thank you.
@silviutudose7868
@silviutudose7868 3 роки тому
respect from Romania; thanks for sharing
@piercebros
@piercebros 3 роки тому
Legend! Thank you so much for your excellent teachings.
@careycraig4360
@careycraig4360 2 роки тому
Excellent Video!! All procedures well explained. Direct and to the point.! I learned a new skill, now for some practice.
@2ndPyleOfVinyl
@2ndPyleOfVinyl 3 роки тому
This is very helpful. I am at my wit's end with trying to repair a Magnavox VR-9655AT01 (Panasonic) VCR. It was my favorite VCR and I have it at a TV repair place. The person has explained to me that the power board has bad traces from a combination of being plugged in for too long and perhaps, some errors that I have made while soldering.
@danielmorgan7702
@danielmorgan7702 2 роки тому
Wow. If I knew a circuit board could be repaired, I would not have discarded the board. Thanks for the video.
@drunkwiizard3483
@drunkwiizard3483 3 роки тому
This is very well presented and informative! Unfortunately, the most information I have taken away from all this is that I don't have the means to repair the damaged board of my Xbox controller where I have soldered in new bumper buttons SEVERAL times, damaging the board a bit each time as I don't have a ton of experience. (ex gf somehow kept dropping the controller on the same bumper and wrecking the small button inside lol.) I have plenty of controllers and all I just like learning and fixing things 😁
@daryx.langdale
@daryx.langdale 3 роки тому
these videos are great and I regret not having watched them before i took my soldering iron to my now botched Allen & Heath mixer. What would be cool to see is a video on fault finding and identifying where and why things went wrong. I thought I had a simple job of removing some resistors and bridging the pads they were sitting on (as suggested in the manual - a simple mod that adds 6dB to the phono inputs at the cost of the warranty), but now I only have signal coming through the left channel on each input, as well as some crosstalk where I can here input from CH1 in CH2. I want to go back and do things properly having watched these vids, but I'm not sure if the problem only exists at the site of the pads I soldered (the crosstalk makes me think I damage in other places). All this to say, keen to see more. Very helpful for a beginner.
@lockdownn-7666
@lockdownn-7666 3 роки тому
very well made video, you did explain things nice and calmly
@thebizzle2605
@thebizzle2605 3 місяці тому
Very very informative, thanks to you I have successfully fixed my vintage 8 track porta studio😊
@game_whisperer1606
@game_whisperer1606 4 роки тому
Thanks for this video. Very clean.
@zalafinari
@zalafinari Рік тому
I was about to toss a plasma ball that I discovered had a circuit board that got snapped in two but wondered if it would be possible to repair the traces without too much difficulty. This video was the first result and was a perfect explanation of the process. Guess I'm not throwing it out until I at least attempt to fix the traces. Thanks!
@mj12eben
@mj12eben 2 роки тому
You make it look so easy and no doubt you’re an Aussie. Thanks mate!
@timw1971
@timw1971 3 роки тому
Great video. This pooped up in my recommended videos, and I hope UKposts continue to give you the exposure you deserve.
@dsmithwc04
@dsmithwc04 3 роки тому
I love it when things poop up unexpectedly! Cheers!
@timw1971
@timw1971 3 роки тому
@@dsmithwc04 🤣🤣🤣 Hadn't noticed until you pointed it out. You've made my day.
@tvcad
@tvcad Рік тому
Thank you for making these videos.
@welshpete12
@welshpete12 3 роки тому
Thank you for posting , great help !
@TerrenceWFunk-ex6qd
@TerrenceWFunk-ex6qd 2 роки тому
Incredible. I will be revisiting this. Ty Ty Ty!! Ste Rose du Lac, MB, Canada!
@purerizzo
@purerizzo 3 роки тому
Amazing! Thanks for the lesson!
@jorgecaraballo5987
@jorgecaraballo5987 2 роки тому
Reviewing all I can before I jump into mounting a couple of simple kits . Great videos! Just like double checking with the instructor..... Safety first
@kibagami25
@kibagami25 3 роки тому
this is great. This will help me get better for sure. Thank you.
@als4621
@als4621 3 роки тому
Nicely done. Thanks for the video!
@Mac84
@Mac84 4 роки тому
Excellent video as always Bruce! This is a great tutorial on trace repair, I now feel confident enough to try and troubleshoot my Quadra 840 AV. :)
@gracedeleon1100
@gracedeleon1100 3 роки тому
This is glorious, been searching for "how to repair a printed circuit board" for a while now, and I think this has helped. Have you ever come across - Giyathan Bewildering Gratification - (do a google search ) ? It is a good one of a kind product for discovering how to repair your electronic items like a wizard without the normal expense. Ive heard some interesting things about it and my mate got cool success with it.
@shyleshsrinivasan5092
@shyleshsrinivasan5092 3 роки тому
Thanks a lot for this video ! Really needed this !
@sumitnsinha
@sumitnsinha 7 місяців тому
Very well explained. I am going to try it on my circuit damaged by battery fumes. Thanks bro.
@kurohyuki5912
@kurohyuki5912 3 роки тому
that was so satisfying to watch
@lumotroph
@lumotroph Рік тому
Brilliant! Thank you for sharing
@victorchorques4893
@victorchorques4893 2 роки тому
Very neat and tidy. Professional job.
@megeezer69
@megeezer69 3 місяці тому
Excellent repair tutorial
@TheEleventeen
@TheEleventeen 3 роки тому
Thank you for this wonderful video !
@RetroWizzard
@RetroWizzard 3 роки тому
Great video, very educational. Thanks a lot!
@garymucher9590
@garymucher9590 3 роки тому
That is a good way to fix broken runs. They do make circuit board repair kits that have runs, eyelets and through hole parts. And the runs are in a lot of different sizes and lengths for just this type work. If you don't have such a repair kit, this method does work. I usually lacquer clear coat the board after repairing broken runners and cleaning it well. It keeps other contaminates off the board that way.
@montenegro3167
@montenegro3167 3 роки тому
Great content Sir! thanks for your videos
@ChiWeiShih
@ChiWeiShih 3 місяці тому
Thank you sir for the tutorial, I've managed to fix the PCB in my car’s climate control panel with limited soldering skill, equipment, and materials.
@landongodspeed8466
@landongodspeed8466 2 роки тому
Fantastic presentation
@paulosilva-dm1qb
@paulosilva-dm1qb 3 роки тому
Excellent!!! Thanks a lot for sharing it.
@raymondheath7668
@raymondheath7668 3 роки тому
Great demo!
@__4762
@__4762 3 роки тому
Thank you so much for this. I have a very good idea of exactly what I need to do now and I can get what I need to repair my Super Game Boy!
@SaiyedR
@SaiyedR 2 роки тому
I love your neat and sharp skills.
@MichaelAStanhope
@MichaelAStanhope 4 роки тому
Awesome tutorial. Thanks for this. Its always nice to see how its done through the scope. Now to get a scope...
@Wallygjs
@Wallygjs 4 роки тому
I wish I could afford one, I am saving up, as my eyes are like Bruce's and need all the help they can get!
@burkusmax
@burkusmax 3 роки тому
Man, that was pro for sure. Thanks for the video!
@courtneywaln8006
@courtneywaln8006 4 роки тому
Best trace repiar video on UKposts!!!
@frankcanha
@frankcanha 2 роки тому
Thank you for creating this great video! I believe this is the issue I am having with a board on my LED message board driver. Cannot find a replacement part for it anywhere after extensive searching and reaching out to suppliers. So, I’m thinking this is the repair it needs as I have observed there are some traces that look buggered.
@georgesmusicchannel2115
@georgesmusicchannel2115 3 роки тому
Nice work, thank you. Learned a lot.
@h.l.a.wanigasekera2177
@h.l.a.wanigasekera2177 Рік тому
Real professional. Excellent video thanks from Srilanka
@6ixss
@6ixss Рік тому
im impressed from your hand accuracy
@juhaxx9906
@juhaxx9906 4 роки тому
Thank you very much for this video. Very educational. I do data recoveries from damaged media and this kind of soldering is sometimes needed. After seen this video I can i the future do this kind of work much better that I did before.
@terryshrives8322
@terryshrives8322 2 роки тому
Really great to learn this, thank you so much
@supergames2073
@supergames2073 Рік тому
Thanks for this I needed it to fix my 90 year old great grandma's humidifier
@1960livvy
@1960livvy 9 місяців тому
Very informative and helpful - Many Thanks
@RobbieLValentine
@RobbieLValentine 3 місяці тому
WOW! This video has helped me lear what Ive been trying to learn on my own for the last twelve months, but in 20 minutes! THANKS SO MUCH! 😀
@RobbieLValentine
@RobbieLValentine 3 місяці тому
Forgot to add something, you mentioned in the intro that once the repair was complete, to check for continuity. I don't suppose you have a video for that too do you mate?
@nachobeards
@nachobeards 4 роки тому
very cool and detailed video thank you
@stephencovrig8373
@stephencovrig8373 2 роки тому
Beautiful. You’re an artist
@rust8infinite
@rust8infinite Рік тому
This was such a fun and interesting guide. My 1st and recent soldering project was de soldering a dvd drive controller for an xbox 360 and re soldering to a new chassis it was only a couple of wires, when I powered on the xbox 360, saw that disc drive opened, and read a disc the amount of satisfaction was immeasurable to me. I think someone dropped the xbox because I tried realigning the tray which is easy to do and even swapped the metal shell outside of it and it kept getting stuck. My next project is replacing the capacitors on another xbox 360 that has the red ring of death.
@peymannaji
@peymannaji 3 роки тому
That was a really clean job. It didn't tickle my OCD :)
Repairing damaged or lifted pads on a circuit board
36:13
Branchus Creations
Переглядів 359 тис.
Beginner's Guide to Soldering Electronics Part 1
33:07
Branchus Creations
Переглядів 1,5 млн
Godzilla Attacks Brawl Stars!!!
00:39
Brawl Stars
Переглядів 8 млн
Первая поломка Scirocco! Балацко попал на мотор.
1:13:12
How To Repair Damaged / Missing PCB Pads || 4 Great Methods
11:54
Mr SolderFix
Переглядів 90 тис.
Can we clean a corroded PCB using FLUX?
31:02
Learn Electronics Repair
Переглядів 10 тис.
Can We Repair A Burnt PCB?
1:01:39
Learn Electronics Repair
Переглядів 27 тис.
How To Repair Damaged /Missing PCB Pads - INVISIBLE Fix  #soldering
10:17
Mr SolderFix
Переглядів 159 тис.
3 Ways to Check Capacitors in Circuit with Meters & Testers
14:48
How to clean Soldering Tip
15:54
Androkavo
Переглядів 5 млн
Data Recovery: Hard Drive Platter Swap in Our Lab!
36:05
Louis Rossmann
Переглядів 1,3 млн
Vortex Cannon vs Drone
20:44
Mark Rober
Переглядів 13 млн
КУПИЛ SAMSUNG GALAXY S24 ULTRA ЗА 88000 РУБЛЕЙ!
27:29
DimaViper
Переглядів 66 тис.