To support the channel and purchase Official Paint Society Shirts and Decals: Paintsociety.bigcartel.com

Another tip is to place the spray cans in warm water before spraying. You get a little more pressure and a little better atomization

Most DIY videos: "First, put your car up on your lift. Then roll over your toolbox with $40K worth of tools." This guy: "We're doing everything by hand!" I love it! Great video.

This was a great tutorial. Just did some Audi wheels yesterday. I didn’t use the exact same products, but your step by step was a perfect guide. They came out incredible! Thanks! 🤙🤙

Trip report with some tips. First and foremost, a huge thank you to Brian and @Paint Society for the video, it REALLY helped my second whack at this go a jillion times better. Considering the number of newbies watching, here's some tips and tricks from a newbie that Brian didn't cover probably because he's old hat at this and it's just a given to him. 1. Buy all of your paint at one time from one place. If you have the option, look at the bottom of the cans and get matching lot numbers. QC seems a little loose over at Duplicolor and the color can vary widely from can to can. If you expect to need touch-ups down the road get a few extra. 2. I only used 2.5 cans of each to paint five 20" six-spoke F150 wheels. 3. I can't speak for any other colors but the Graphite is really gritty, the Sprayway wipe is a good idea between all of the base coats. 4. Avoid trying to paint the wheel upright, hard to see where you're getting good coverage. Laying down at an angle like the video shows worked best. I did mine with a light coat left to right, then a light coat up and down on each layer. 5. Don't make the first spray out of the can on the wheel, give a quick shot away to avoid spit/splatter. Wipe the tip often as suggested. 6. Get some slip on shoe covers. Overspray on the floor builds up quick and sticks to your shoes, then you forget and go walking thru the house leaving paint on your floor that's a SOB to get off. 7. Watch the video and take notes. What sandpaper did he use for that? How long between coats was that? Lots of steps and times in this video, handy to have them written down.

Great job, not all of us have a $2000 AUD compressor and $750 AUD spray gun, and the tips you gave are brilliant.

Perfect timing! I was getting ready to do this on my curb rashed alloy wheels

This is the first video ive seen that specifies the amount of time you wait between paint and clear. And so many more new tips. Finally! Thank you!

I never liked the dark gray color of my Honda Ridgeline rims, so I followed your instructions using Duplicolor silver paint over white primer and clear coated with the 2K clear coat. The tip about using the SprayAway glass cleaner to smooth the surface is genius. I am very pleased with the results. Many thanks!

Best tutorial I've seen. Straight to the point yet calm in delivery. Cheers,

Awesome video. I used to spray can computer cases for mods and a good tip to avoid gritty paint or stippling is to lay the can in some hot water to loosen up all the paint that does not get thoroughly mixed.

Just did the factory wheels on my Audi TT and they turned out Awesome! I followed your method to a tee and it's excellent! Thanks, Brian!

Well done! With any paint project, prep is key. This video illustrates doing it the right way. Your newly painted rims are going on your coveted ride and taking shortcuts does not work. They are going to get a lot of abuse from the road, brake dust, repairs, etc and you want a quality durable finish. No point in doing it if you're gonna do it half-assed. Worth spending the time on the front end to get the results and longevity on the back end. Great video!!

Your's is the "BEST" instruction on how to do wheels yourself Brilliant...Thanks

This is the absolute best in depth DIY paint your rims video on the internet

Your knowledge, explanation, way of presenting everything is priceless. Thank you.

I did this a few years ago when I put 05 Acura TSX wheels on my 07 Accord. I followed almost the exact same process and it worked remarkably well. I had a couple of chips I had to go back and fix when the tires got remounted but other than that, they were great.

Man this guy gives free seminars on UKposts. I'm planning on repairing my dad's w211 e200 after army. If the shipping to Greece isn't insane I'll buy a t-shirt of yours and tag you when I get it all done. You are a blessing thanks a ton

Great video, really clear and very informative. Just what I need to sort my TT wheels out!

Thanks for the tip regarding how it isn’t necessary to use primer on spots that weren’t repaired. I have a nearly new set of aftermarket wheels in perfect condition that have a flat finish that I now realize that I hate, and I want to spray them in a gloss finish. It’s good to know that I can clean them, rough them up, and skip to base and clear coat.

Asked for this a while back and you nailed it, thanks! Look forward to more videos!

Great video. I'll be attempting this in the spring and this video gives me a much better instruction on doing it correctly by can.

Great video as always and full of useful info like tips, drying time, etc! I wanted to know how much of each product you did use and I found that it is mentioned in the description! Keep up the good work!

Just picked up some wheels from my local pick a part. This video was really well timed for me.

15:00 love the afterspray tricks.

Thank you for these videos. This channel is giving me the motivation & confidence to restore my rims sooner than later.

The best tutorial I've watched on UKposts. Simply awesome. Thank you.

I came here to learn technique on all that was shown. I was not disappointed, rather encouraged to go ahead on my own wheels. Thanks for that.

Dude, you killed it! They look amazing! I think the most important part of the whole project is "patience"! If people follow the steps you showed - look out! America is going to get shinier! Great job! You just gave me the confidence to finish a job I've been putting off for a while! 2k clear, here we go! 👍👍

That looks good brother nice job and your getting there on your subscribers nice going God Bless and keep up the good work

once again u show me some thing i was wanting to do and needed some professional advice & the right way to do it ,thank s great viedo

Love this video! Have to tackle the curb rash on my 2010 Fit wheels and seeing those wheels in that color makes me kinda think about painting my stock wheels a different color, but I'll probably just keep them stock. Thank you and keep putting out these great vids! P.S. Killer music at the end! Made me smile from ear to ear!

Great work, thank you for showing it step by step. Great work!

Dude thanks for this video. Looks like I’m gonna have a weekend project soon! 🤙🏼

Pretty cool, I was looking to paint my ITR wheels a gun metal color and throw them on my 1st Gen CR-V.. and to see these wheels done and go on a CR-V like mine was confirmation 🤟🏼🙌🏼

Thank you for all the info just did my wheels really happy with the outcome

Great channel!! Very thoughtfully explained and for every level of equipment. Now I know what I have been doing wrong for many years! Could you do one on painting wheels with hyper silver?

As always you make it look easy. Amazing attention to detail with ultra professional results, even with a rattle can. Thank you sir for the encouraging and instructional footage. It is inspiring. Subscribed and smashed the like button without hesitation.

Can’t wait to fix my curb marks! Thanks for the tips!!!!

I've used a lot of the eastwood 2k aerospray cans. I think something to stress is the temperature needs to be as close to 70f as possible or higher and most importantly you need to shake the crap out of the can before and after you pierce the hardener. I had issues when I first started using the 2k aerospray paint because I wasn't shaking it well enough especially with the color paint, the primer isn't too bad. I want to say it's the cans with the white knozzles that really need that extra shaking and make sure the can is warm it doesn't need to be hot but just warm. I've easily used over 250 cans of that aerospray paint and I haven't had a single issue after I figured out the temperature is important not just with your project but the actual can needs to be warm it seems like common sense but it's something I make sure of everytime now and most importantly you have to shake the hell out of it like 3 minutes before and 3-4-5 minutes after piercing the hardener. I'm sure I go slightly overboard with the shaking but when I first started using it every single can clogged up because I wasn't shaking it enough I was doing 2 minutes before and 2 minutes after and that wasn't working well for me the cans clogged up not just the tips but the whole can. Like I said the primer is more forgiving I believe all the cans with the black knozzles are more forgiving. Then also the primer goes a lot further than the color like a lot further so get extra color. Otherwise I love that 2k aerospray stuff it's really good paint especially if you prep well and keep it at temperature while it dries, I use the chassis black on roll cages and bumpers and stuff on jeeps and it's very durable, surprisingly durable and very easy to use especially when you just have a single item to paint.

Just bought an Acura TL with exact wheels. This vid will help me do the job. Thanks

Glad i ran into this video, i just bought the same cans for my rims

Great video! Very detailed! Thanks so much, Brian!

Your videos are so helpful and so real. So much good information.

This channel will go places, full package. Keep it up!

Amazing results! Thanks for the video.

I really appreciate this level of perfection and detail. But I think I could get 3/4 of the way there with about 1/4 of the perfectionism. You are an excellent teacher and a skillful painter.

Very nice, love the masking! I may have missed it but on the back of the Dupli-Color can it states, "for additional coats after one hour, wait seven days for the paint to cure." Because this is an enamel it needs to set. If you coat with the clear too soon it could mess up all of your work. I'd wait to do the clear coat. If you use a lacquer clear coat it will definitely mess up the enamel. Always check to make sure your product makeup matches it's just easier, especially after you spend hours prepping. It's 90% prep and 10% finish that makes the wheels look good.

one of the best video I have seen in years quality info and what a finish thank you from the UK

Thanks for the video. Ive got to lay down some clear and i think it will look very good

Happen to stumble across this vid. Excellent, step, by, step to recolor rims! A project my son wants to do to his car with the exact same color. Thanks for this. I’m a subscriber!

Good video, bought set if alloy rims off junker for my camry. Coating peeling do did this repaint thing came out good. Now if you get curb rash and want to fix here is a tip. To fill gouges use jb weld as filler. Stays for ever and when hardened can be sanded lime metal then touch up paint.

Wow! Im speechless! With just canisterpaint! Wow!

I am getting ready paint some wheels, and I've seen all the wheel painting videos on youtube. This is the best video on painting wheels yet. You should get some kind of award. excellent video

Those look like they just came out factory finish! Nice job and thanks for the education!

Love your stuff Brian, I've learned a lot and have built the confidence to take on more projects of my own. I would like to see a video on how to setup a air compressor for body work and painting.

Best tutorials on UKposts hands down!

Got some old 13 inch Crager's out of a field, chrome still passable with a good polish but inside the rims was too corroded. The bead wouldn't set well, slow leak even with goop. I cleaned the inside with a wire wheel and used metallic bondo to smooth them out and primed and painted. Good for nearly two years now.

Wow awesome video bro! They came out sweet dude keep up the great work!!

Wow I literally just refinished a set of TL wheels this past weekend

Great videos, very detailed. Nice work!

Very nicely done I will follow exactly thanks for the lesson.....

UPLOAD ANOTHER VIDEO! lol. im patiently waiting! im not just meaning so i can learn more stuff, i actually enjoy watching you as a person! your an awesome guy! jumping on your channel to hear your voice and seeing your artwork is like coming home and eating a perfect steak infront of the fire! didnt mean for that to sound cringy but it sounded good in my head lol. love your videos though, you do amazing work and also make my day better! hope this motivates you! thanks mate :)

Really Nice Job! Geez! Brand New! What a Skill!

Thanks. Really good video. Thinking of doing my tundra wheels. Two tone.

Thank you for this great video! My wheels look bad. Now I can do something about them!

Good job man. Keeping these videos real, for average people. Well done!!! ☮️. 💡🤯🎯

Amazing tutorial! Thank you for taking the time to cover each and every step in detail. Also the tips about products was helpful because there are so many out there. Going to attempt to spray some brand new silver wheels and make them black. Any special considerations for painting wheels with a very complex and intricate pattern?

awesome job! loooooooooooooooooooooooooooooooooooooooooooooove the detail. this has to be thee best wheel back to life video. keep it up guys.

Omg I just finished a set of 19" AMG wheels. Gave up trying to strip off the coatings with paint stripper so took them to get them acid dipped. Mirror finishing the spokes, masking then spraying with primer, base coat and lacquer. Time, effort and costs considered, I wish I'd got them done by a specialist. Although they looked great when done.

Nice job! Would love to see a video about restoring/painting faded black trim plastic on cars.

Nicely done amigo Looks superb!!!!

Beautiful work!!!

Great Video as always!! Thank You Sir!!

Bro!!! I'm going to paint the same set of rims! I'm more than hyped for it now after seeing your sick results!

Really nice video, I’ll try to do it in my elantra summer wheels 🙂 thanks 👍

Wow, very nice result Brian. Dutch regards, Nico.

Bro, doing a set of wheels for older tundra, this vid makes it happen 😎keep em coming

PRICELESS, THANK YOU MAESTRO….

My 05 acura tl has the same wheels and wanted to paint them but wasn't sure what it would look like with my car color. This is great.(they also have a bunch of curb rash from previous owner)

Great video! One of the best I've watched.

Always been a fan of those Honda wheels. Haven’t seen them in that color before.

Good quality at home paint video! Thanks

Thank you very much for that video I just but for rims yesterday for my little 2001 Kia but I couldn't get white it's a blue car and I wanted white so now I know what to do. I appreciate it thanks guys

Respect for you, thank you

Thank you for teaching us.

Brian is the king of paint and technique.

Very well explained! This is the best DIY wheel paint video. Power to you!! Love from India :D

Best video on wheel painting I have seen!!! I will follow step-by-step. I have a question though, in the past I had issues with 'orange peel' after the Rattle Can clear coat was put on - what was I doing wrong? Thank you and keep up the good work.

Good video eastwood 2k stuff is really good paint and easy to polish. I figured out a way to make sanding so much better with a sheet of paper. No folding needed just put duct tape on the back of it. Only flaw with it is you have to mark it with the grit with a pen otherwise youd have to guess. Remember dont overthink it, its just duct tape.😂Thank you for your knowledge and your awesome techniques.

One of the best video thanks nice work

That was very educational Nice work

Magnificent! Such a brilliant idea... your diy parking sensor!!!! I caught it at the end... but I also like how you set up a mock booth. Did you bother wetting the floors for dust? I guess the cans don't provide enough psi to disturb the dust. Great job on the wheels BTW, I'm thinking of doing mine next summer.

TL wheels on a crv? Looks sick! Love it man great job and thank you for the vids..confidence for painting my 93 4door ex.

Pretty nice, am impressed

Thank you! I need this

Great job now I can try to do mines

Thank you for making the video.

Thank you for sharing 👍

Never over think!!! Love it 😍