Automatic Pet Waterer
Переглядів 1,417,149
4 роки томуAutomatic waterer for pets, homemade automatic waterer of high durability manufactured with PVC accessories, with an approximate capacity of 5 liters, can supply water to your pets for a week without the need for replacement.
Materials used:
PVC pipe 50 cm 100 mm (part where water is stored)
20 cm and 53 cm pvc pipe (works internally to maintain level without overflowing)
2 knees 90 ° pvc 100mm (used to make the bowl)
1 knee 45 ° pvc 100mm (top or water inlet)
1 PVC plug of 100 mm (drinker cover)
1 sheet of EVA (seal)
´´Tips and compliments are always welcome``
´´Leave them in the comments``
If you are not yet part of the pasta, SUBSCRIBE ☞
/ @meantimeentretempo
Activate 🔔 not to miss any of the channel's new videos!
▬▬▬▬▬▬▬▬▬ Social networks ▬▬▬▬▬▬▬▬▬
FaceBook: / entretempo
Instagram: / meantime_entretempo
The Meantime channel has the ´´Do It Yourself`` group on FaceBook and WhatsApp, with the aim of exchanging ideas, doubts and any subject related to the range of leisure and recreation crafts. Participate and share ideas:
Facebook Group: groups/22016...
Grupo N ° 1 WhatsApp: chat.whatsapp.com/IzxkT3Axo5e...
Grupo N ° 2 WhatsApp: chat.whatsapp.com/ISz23K1vVbF...
@zarlus8 2 роки тому
There are many comments asking how this waterer works. It's only a guess as it isn't possible to see the water level inside the larger pipe. However, from what I can tell the video shows two pipes; smaller inner pipe, (for air) and larger outter pipe, (for water). The inner pipe passes through a divider. The divider at 5:26 has a small hole drilled in the center. This hole allows water to pass through slowly; (due to atmospheric pressure), from the upper reservoir to the lower dispenser "U" shaped area. The divider is placed, (inside the larger pipe) at the same height position as the desired water level for the dog to drink 7:26. This level also covers the bottom opening of the smaller inner pipe. When the dog drinks, the water level drops in the "U" which allows air into the "U" and up through the inner pipe. Atmospheric pressure pushes on the water in the reservoir allowing water to pass through the small hole in the divider. The water will fill the "U" until it covers the bottom opening of the inner smaller pipe which stops the water from filling and spilling out.
@MeantimeEntretempo 2 роки тому
Exactly
@zarlus8 2 роки тому
@@MeantimeEntretempo thank you
@twowheelfarm9024 2 роки тому
It is also very important for the top cap to seal air tight, and the hole in the divider to be small. As it will be running out while you fill it until you get the top cap back on.
@radamest2 2 роки тому
Thank you!
@kingkaleem6942 2 роки тому
Is the cap necessary to prevent over flow?
@felinerescue5272 2 роки тому
Nevermind, I'll just buy one.
@vernonjermin 2 роки тому
😂😂😂😂😂
@girthworm6895 2 роки тому
I'll just use a bowl thanks
@sameasnone Рік тому
Where?
@alexanderyan89 Рік тому
Where to buy can you share the link ? Thanks
@unveiledwithouttears1370 Рік тому
You should buy 2, just in case.
@jordanjgoldsmith22 Рік тому
And for those who are still confused how it works… it’s quick, but he first drills a small hole in the center of the divider before making a second hole for the inner pipe/hose. This is where water passes through and the inner hose allows air for the slow distribution of water. So the divider has two holes… one small one at the very center and a second which the inner pipe passes through!
@thomasmchugh1989 Рік тому
THANK YOU! I thought so but your confirmation was super helpful. Love this design
@gustavojimenez7802 Рік тому
Dont forget it needs to be airtight otherwise will spill the water after a while
@chickenwhisperer8410 7 місяців тому
Yes it looked almost as if he had just made a center mark without drilling all the way through. I figured that it went through but it doesn’t show it very well
@Ryan62751 2 роки тому
Lol nice invention, I especially love the part when he shows the dogs how to use it.
@blixten2928 3 роки тому
I love this channel! So cool, no-nonsense, just get right into showing us. REALLY GREAT, thanks!!
@sebytro 2 роки тому
This is awesome! It's a great space saver since it stands vertically and doesn't take so much space on the ground. Thank you.
@adamm2909 2 роки тому
Excellent job 🇵🇸❤️🕊 Love and respect from Jerusalem the capital of Palestine 🇵🇸
@alfredodiaz8229 3 роки тому
I think I know what is missing, in the materials I see that one of the small tubes is missing. The big one is the respirator and the small one supplies the water, but in the video you only see how you put on the respirator. "20 cm and 53 cm pvc pipe (works internally to maintain level without overflowing)"
@busigh 2 роки тому
I like the principle of controlling the water level really cool. I designed my own water dispenser before watching this but incorporated a system to automatically fill the chamber too rather than manually filling the reservoir. Simply I added a toilet bowl all in one fill valve with float and connected it to water supply. My design didn't use his method of controlling the water level at the feeder outlet to the dog either. I created a port and installed a hose on my water reservoir 2 inches below the water fill line and ran it to the dogs water bowl placing it 2 inches below the water fill line. This way the water level in the bowl controls the filling of the bowl and the toilet valve float unit controls the filling of the reservoir. No heating up of PVC (which releases toxic fume from what I read) just drill two holes and attach PVC and you are good. My unit allows for multiple hoses to multiple dog water bowls attached to the same reservoir.
@davidgraemesmith1980 2 роки тому
I can just about remember when magazines showed diagrams of projects like this 😊 yup I'm old at 41yrs
@drrussdc 3 роки тому
Great application of physics 👏 well done!
@mynamesnotrob 2 роки тому
That’s clear as mud instructions.
@notwrkn2mch 2 роки тому
We are out in the Arizona desert and i fill a poultry waterer for the local birds, rabbits and quail..... luckily no coyotes yet and your technique would be a much better solution for me.... I need to watch it a few more times to get the concept of why the water doesn't all dump out the bottom
@raven314 3 роки тому
love this design ... easy simple .. thanks Meantime for sharing!
@sansan925 3 роки тому
Estaba mirando recetas de cocina y terminé mirando este video. Muy bueno 👌
@c-martz2846 3 роки тому
Brillante amigo!
@diegofariacarlos 3 роки тому
Muito bom, gostei muito da engenhosidade!! Não faz bagunça e usa toda a extensão do PVC!! 👏👏
@elisasalamanca842 9 місяців тому
Gracias me ha resultado muy práctico su video..... y me encanta la limpieza de su trabajo....gracias por compartir.
@gerlandoalvesgomes94 3 роки тому
Ótimo muito bem feito, e o estímulo ao cão pra usar o bebedouro foi muito inteligente kkkkkkkkkkk
@funn4547 3 роки тому
So nice! Want to make it but the directions say 2 internal pipes but video only shows one😩. Please explain what did I miss ?
@jbiliHacker 4 місяці тому
3:20 nice invisible watch!
@Sloansteelsigns 3 роки тому
Do you have the plans for this design?
@kubeckunderka453 3 роки тому
Hello, please, must the knee bowl have a 90 ° angle to make the bowl or can the knee bowl be of different angles?
@marianam.desousa2341 4 роки тому
HAHAHAHSHHSH catiorada adorou!!! Q trampo bonito!!
@josselinelemanach7430 10 місяців тому
Un homme qui aime la précision et le travail bien fait, ça fait plaisir à voir !
@JohnB3363 Рік тому
I would’ve used a clear pipe and put tape down the length of the last third or so before painting it so I could monitor the water level.
@cesarmezaycabrera7358 Рік тому
Idea maravillosa, gracias
@JoseCarlos-ol5by 4 роки тому
Aí sim... Belo trabalho . São José do Rio preto sp Brasil 🇧🇷
@MeantimeEntretempo 4 роки тому
Valeu parceiro
@jasonmiller5995 10 місяців тому
‘Damn, that looks easy”~said no one truthfully. Doc Browns’ dog food dispenser for his dog “Einstein”, was as convoluted as this. Great job though.
@onetruesoldiervt3686 2 роки тому
Nice 👍🏼 job I wish I could make one but seems a lil tricky
@oldhiway66 3 роки тому
BRILLIANT! Hilarious ending. I think the plumbing industry owes you for making P traps 😆
@elyserva7903 2 роки тому
I think it would be cheaper just to buy the waterer! Saves you the trouble! 😄😄😄
@valdirrocha3431 2 роки тому
O cano de 25 mm q vc colocou dentro , é só encaixado ?
@gabrielrissi608 4 роки тому
Top demaisssss
@richier.1585 2 роки тому
Good job. Buena idea.
@Skashoon Рік тому
Easy if you have patience and tools. I lack both. On to the next video. Great waterer, but it’s too difficult with the few tools I have.
@yagocorrientes 2 роки тому
vi modelos con válvulas que en argentina no se consiguen... este me sorprendiendo.... el agua cae por el agujero de 2 mm verdad?
@angelortiz9784 3 роки тому
Ive seen many versions of this on the tube, but this one seems more efficient. Would it be possible to replace the copper with CPVC 1/2"? also non of the versions have a way to know when it needs to be refilled. maybe a clear tube version would solve this problem at the same time you could make sure the water environment is clean.
@MeantimeEntretempo 3 роки тому
I've tried with smaller tubes, but unfortunately it doesn't work
@swangodesigns Рік тому
@Meantime that's my main concern is sterilization.
@dtec30 2 роки тому
Not sure I quite followed it was it like a bell syphon ?
@Dudu291097 4 роки тому
Que engenhosidade daora mano... A idéia tá simplesmente genial! Como sempre, as melhores gambiarras com quem entende do assunto!!! Tá de parabéns mano 🤙🤙🤙🤙
@MeantimeEntretempo 4 роки тому
Valeu parceiro, você é o cara!
@ronwillett9014 2 роки тому
Can you get written instructions for waterers?
@alefalves4299 4 роки тому
Ficou top irmão, com a crise de corona vírus faça umas máscara para o povo
@MeantimeEntretempo 4 роки тому
Que ótima ideia em, valeu!
@GonzoDonzo 2 роки тому
They do sell these for about $30. Hooks right up to your hose. With the cost of pvc its probly a better route
@GreenChilliD Рік тому
Link? Keyword for search?
@jorgegranada4964 3 роки тому
Make it smaller and its a good hummingbird feeder.
@suspence25 2 роки тому
Chris Notap should try this one.
@charjaylorenzo5429 2 роки тому
Do you fixed? Circle pvc inside the tube?
@sanghpriyverma9845 2 роки тому
Please reply me the cap on the top is necessary ?
@sholland42 2 роки тому
A real hacksaw would have made it much easier. Great idea, thanks.
@fabianovargas126 2 роки тому
Boa tarde, gostei da idéia só uma dúvida você colou o cano de 3/4 que fica dentro do círculo de PVC.
@JoseAntonio-yb7yi Рік тому
Também tive dúvidas nessa parte,foi feito um pequeno furo no centro da quela tampa cega e um para o cano é isso,o cano 3/4 funciona como o que lá dentro,a água não sai por ele certo,a água sai pelo furo do centro do tampo cego né isso,precisa colar esse cano ou só deixar na forma obtida pelo esquento?
@psyco4916 3 роки тому
Thats a cool idea bro. I figured it out how this works after couple of minutes. Great work bro.
@bhekisfruitful488 3 роки тому
I'm still lost you know
@psyco4916 3 роки тому
@@bhekisfruitful488 bro its simple. You see that small hole made by a nail. If you dont close the top end with cap the water will ooz out like gravity action. The small hole prevents quick water flowdown . So you get enough time to refill it. Then you close the top so no air going in so the water flowdown stops. Then when the dog drinks water the water level drops and air can pass through the inner small pvc, the water will flow down untill the water level comes as earlier and hit the inner pvc down end. Phew I think you understood now. If not i will explain again 😅😅😅
@wushugirl6941 3 роки тому
@@psyco4916 so we should put water in the inner pvc pipe, right?
@psyco4916 3 роки тому
@@wushugirl6941 no the inner small pipe is for air to pass from botom when dog drinks water. The water is filled inside the main pvc.
@wayjeen 2 роки тому
@@psyco4916 i watched it 2-3 times and figuring how the water flow down knowing that the overflow pipe is not the one sending water. And i totally get it when you mentioned the small hole by the nail ! Thank you for sharing !
@antoniosaraiva9737 Рік тому
e muito bem explicado
@L.Salvatore 3 роки тому
Good idea
@mikelestad2 3 роки тому
Cumpa la tubería de adentro le hiciste agujeros para que siga llenando el bebedero , o solo sirve como respiradero ? No cache mucho esa parte .. gracias .
@Jaimeb453 3 роки тому
Creo q se tiene q llenar del diario
@Jaimeb453 3 роки тому
No se como bajara la demás 💧
@justyalicea2602 2 роки тому
I've built something similar for my chickens. How do you keep the inside from building up algae/mold? I had a layer of green film inside the pvc in less than 2 weeks
@MeantimeEntretempo 2 роки тому
whenever the slime builds up, I use a hypochlorite solution with water to clean it.
@sbstoecker 2 роки тому
A very small amount of hydrogen peroxide in the water will help.
@douglasdishroon1834 2 роки тому
@@sbstoecker Hydrogen peroxide slowly decomposes into water and oxygen. An elevation of temperature and the presence of pollutions enhance this process. This is a redox reaction. Hydrogen molecules partly function as reductors and partly as oxidizers.
@sbstoecker 2 роки тому
@@douglasdishroon1834 Would you be able help me breakdown then what processes are happening to help reduce algae build up? On the rough, my field study compared the following - A 32 liter chicken waterer, refilled everyday. 3 days at 30 Celsius and there is significant algae growth in the waterer. Now the same but with a
@douglasdishroon1834 2 роки тому
@@sbstoecker Hydrogen molecules partly function as reductors and "partly" as oxidizers. It's still helping, it's merely less active. Meaning your concentration of H202 could be higher.
@jeffk7626 2 роки тому
i don t understand how it works with the smaller pipe inside.
@davidcastillo379 2 роки тому
Me either, I wish he would have explained it
@guyfisher2050 2 роки тому
Great idea, but not sure all those chemicals are food safe (caulking and paint)
@dani644b 2 роки тому
The end was cool 😎
@woofy548 3 роки тому
a big bucket of water works too and is a lot easier to clean and change the water
@MeantimeEntretempo 3 роки тому
A tank would also work, but I have no place for one at home ...
@tubrogg 3 роки тому
Do you have a step by step video of how the water holds inside the pipe?
@MeantimeEntretempo 3 роки тому
Unfortunately not, but the system is based on vacuum
@tubrogg 3 роки тому
Do you know where I can find this vacuum concept on UKposts?
@just2botheru 2 роки тому
But how do you clean it?
@mmawad100 9 місяців тому
If the water does not flow down while the top cap is away Why does it flows down when the cap is on ?, Did any one build that and it actually worked ?
@alfredodiaz8229 3 роки тому
en la lista de materiales falta el adhesivo usado, no parece el típico adhesivo de PVC.
@rosalbagonzalez4522 4 роки тому
Los perritos😂😂👍👍
@babyriver8121 Рік тому
Es muy buena idea, pero cual es la idea del cobre adentro, si me wxplicas porfavor
@MMFORTAL 3 роки тому
Great
@Roady2010 2 роки тому
Amigo no disco de pvc que recortou e perfurou com o cano fininho , o disco é colado por dentro certo? Mas o cano fino só entra na pressão dentro do disco é isso? Sem cola mesmo? O segredo todo ta ali, qi a agua escorre devagar por esse furo no disco? Eu ja preparei a o grosso ai, so falta esse disco e cano fino, ta funcionando mas como um bebedouro de gaiola de passarinho, vedei a tampa superior e avasteço o bebedor de cabeça pra baixo, viro rapido, e a pressão estabiliza kkk
@evandromax4121 Рік тому
Não precisa desse cano fino eu fiz sem e deu certo.
@DanielLaRusso-Do 3 роки тому
What is the exact purpose of the thin pipe inside the waterer? The water is droping through the tiny hole you made in the middle of the flat round piece that holds the thin pipe?
@MeantimeEntretempo 3 роки тому
The larger inner tube serves as a bridge for the air inside the reservoir to escape and maintain the water level.
@schumpa17 3 роки тому
You don't even need the small tube in there it serves no purpose. You could have drilled a 1/4 inch hole at the top of the lid and that would be enough for air flow but regardless air bubbles would make their way up the pipe as the dogs drink n the water level will always stay the same cause it's called gravity. You people must not have a lot of knowledge to b impressed n fooled by such a pointless video. Oh n don't worry bout him putting alcohol in the dogs water that's real good n health for their livers. Should be in jail for animal abuse and I'll b sending this video to the aspca
@mehmetberke5121 3 роки тому
@@schumpa17 Its not called gravity domass. If he had just drilled a hole the two openings of the pipe would have the same atmospheric pressure so all the water he pours in would just spill at the bottom. The mechanism with the small tube keeps the pressure difference. This guys tutorial is worth dog shit without correct display of that mechanism anyways.
@mustang268 2 роки тому
@@mehmetberke5121"domass" I wouldn't call people dumb if i where you lol and sorry you dont need that inner pipe at all the top cap being air tight is more important and I'm a plumber I know what I'm talking about it will work just as good without it don't care if you believe me or not so dont bother with your childish response either won't read it
@alexanderyan89 Рік тому
@@MeantimeEntretempo is there anyway can buy from you ? We need that !!!!!😅
@susannahb2723 Рік тому
The music is a whole bop at 1.25x
@IBMDOCTOR 10 місяців тому
Not bad but Water warms up My idea to have flap to drain warm water and debris also mounted to the line
@saidraid9855 2 роки тому
I did the same thing but doesn't work. Is there any schema with what should not to do ?
@jmti1356 Рік тому
Bonsoir j' ai réalisé le même que vous mais je rencontre un problème : L eau coule en continu - prise d air ? En tout cas ingénieuse idée
@sandubercea9952 3 роки тому
Super
@SolidworksUnlimited 2 роки тому
Lol that burp
@polesejunior 4 роки тому
Estranhei o título que me apareceu, parecia uma tradução esquisita, aí olhei o título na aba do navegador e vi em inglês, credo, sente o poder do canal!!!!! Hhehehe
@malukinha7036 4 роки тому
Kkkkk
@calebwiggins3042 2 роки тому
Should have done that outside with a heat gun cause the pvc just ruined your toaster oven
@mirfster7425 2 роки тому
Yep, Toaster Oven is now "Toast" for any usage with food.
@valiyevdavlatbekrustamjonovich 3 роки тому
Good
@sylgibbons859 3 роки тому
👍👍
@GreenChilliD Рік тому
Who doesn’t like tequila? 😂😆🤣
@Young937phoenix 2 роки тому
You can just buy the waterers that screw into pvc that ends up cheaper than making one of these and works just as well
@CosmicJib 2 роки тому
I’m a plumber and we don’t use tape for a straight cut we just eye it
@Reddylion 2 роки тому
Nice...
@kathrynw.9754 2 роки тому
Love that music! Who is it? Also the waterer is cool too.
@antoniollamas6367 3 роки тому
10:16 “You can lead a horse to water but you can’t force it to drink”
@Th3Crow10111 2 роки тому
Great video mate. I have to try this out. For those that don't get the joke at the end... faq em snitch's.
@jongrubaugh160 Рік тому
Great idea nonetheless.
@GreenChilliD Рік тому
I’m frustrated. So, I built this. I am having an issue when I close the top. It seals but wont refill. As soon as I open the top it overflows. Is my vent pipe leaking?
@GreenChilliD Рік тому
I think I know what the issue is. My elbows are different than yours. They have more of a drop. Yours are basically perpendicular. My air gets trapped in the elbow at the back because the front has to drop very low before air can pass from the front to the back. I bet if I drill a hole just below the diaphragm and above the bottom of the vent pipe it will fill the front to the top.
@GreenChilliD Рік тому
Yup that did it. Filled right to the brim in the front. Physics 🤣
@RomSoloO 2 роки тому
Man, they don't speak spanish, you wrote Agua, that's why the won't drink it 😜 just kidding, amazing inventions, I'm now gonna try at home!!
@odairmarquesdealmeida1572 3 роки тому
Faltou explicar como funciona o sistem
@mustang268 2 роки тому
You did alot more then you really had to
@fabioklasener3013 3 роки тому
Teria como explicar melhor a parte do cano interno, as medidas
@antoniosaraiva9737 Рік тому
exaaaato
@marcelalarroque9378 2 роки тому
Que pasa si no le pongo el caño fino que le pusiste adentro?
@thehazelnutspread Рік тому
I loved it up until you put in the black circle. You could have done a lot more to explain how it works with the small grey tube.
@rushikeshmore7260 3 роки тому
In How many days water is dried ??
@evandromax4121 Рік тому
Muito bom eu tenho desse bebedor só não entendi porque o cano dentro .
@MeantimeEntretempo Рік тому
Para manter o nível da água e possibilitar a passagem de oxigênio para parte superior do reservatório.
@heut4384 2 роки тому
I do like your engineering work. It does look very nice. However, I can see, it will take awhile to make just one (i.e., cutting the pipes and otherpieces, gluing, painting, etc.) I would imagined, you may had been working for a few hours....? Especially, you have to be very articulated. For me, I like alittle more simplicity and quickly to changing water, etc. Lol. But, thank you giving us more other option.
@mustang268 2 роки тому
You dont need to do as much as him all you need was PVC glue he over thank it I built one in 5 minutes but I'm also a plumber so that helps
@pinkmosey 3 роки тому
Make mini one for hamster pls
@alexisyairvalenciamendoza1454 2 роки тому
Es jenial
@aleonvc842 4 роки тому
Wow! How did that work?!?
@MeantimeEntretempo 4 роки тому
vacuum
@aleonvc842 4 роки тому
Yes. But vacuum is a partial answer. Water normally levels itself. But this one looks like it just refills to a certain level always (hence the "automatic" in the name) to a level thats is lower! Very very interesting indeed! Very crafty! 👍👍👍
@MeantimeEntretempo 4 роки тому
@@aleonvc842 Thank you very much, the ideas contained in the letter are as follows: whenever the vacuum is formed inside the reservoir, the atimosferica pressure on the outside is higher than on the inside and, therefore, keeps the water from the basin level without overflowing
@schumpa17 3 роки тому
It's called gravity.
@amithmalik4648 3 роки тому
How does the water around the smaller pipe get into the pipe
@mikewerner3797 2 роки тому
Probably has brain damage from the PCB fumes off the melting pvc😄 I’m sure his mom appreciated him using the kitchen toaster oven for his “project”.
@howardsternisbatman 2 роки тому
And the Granite counters. 😂
@BamaGard291 2 роки тому
I must be slow. I watched this about 10 times, and I’m still not seeing how this works. Edit: Seriously, please explain how this thing functions. I honestly want to know.
@zoltanszilagyi5673 2 роки тому
Same feeling
@authorized411 2 роки тому
To fill: put cap the drinking end To drink: put cap on fill end, remove cap on drinking end See cap on fill end 10:17
13News Now
Переглядів 9 млн
Ветерани космічних військ
Переглядів 548 тис.
BBC News Україна
Переглядів 843 тис.
Boutique de Garagem
Переглядів 2,5 млн
İbrahim Yıldız
Переглядів 864 тис.
Galeri Saturasi
Переглядів 2,3 млн
L'Atelier d'Adrien
Переглядів 40 тис.
MaxxPC
Переглядів 164 тис.
Notebook1 Ассоциация сервисных центров
Переглядів 51 тис.