Building a 6.5 inch SUBWOOFER (for Sound Bar V2.0) - by SoundBlab

  Переглядів 432,252

SoundBlab

SoundBlab

3 роки тому

This subwoofer was designed around a down-firing Tang Band 6.5 inch subwoofer driver. It is a ported bass reflex enclosure with the port firing forward. The goal was to have a relatively small and elegant looking subwoofer that can fit into most home environments. This subwoofer can easily be integrated with a pair of stereo speakers or the sound bar project that is also available on the soundblab.net website for purchase.
The subwoofer design includes a plate amplifier that can be set to 2.1 or 0.1 output. This provides you with the ability to then use this subwoofer with any system or other amplified speakers or just set it to 2.1 and connect a pair of stereo speakers. The output of the specified plate amplifier is 30W+30W stereo, and 60W for the subwoofer channel.
When following the build plan for purchase (www.soundblab.net/build-plans/), it can easily be built with everyday woodworking tools, and even by someone with beginner woodworking skills. The construction follows butt joints.
When following the build plan, the end result should give you a speaker that will have the following approximate specifications:
Power Output: (Mono) 60 Watts (4 Ohms)
Bass Principle: Ported or Bass Reflex with approximate -3Db of 35Hz.
Approximate Size (W x H x D): 240 mm x 400 mm x 209 mm
Subwoofer BUILD PLAN: soundblab.net/build-plans/
Sound Bar BUILD PLAN: soundblab.net/build-plans/
Sound Bar & Subwoofer Combo BUILD PLAN: soundblab.net/build-plans/
Electronics, Speaker Drivers & Related Parts Used:
- Tang Band W6-1139SIF 6-1/2" Paper Cone Subwoofer Speaker - (US) parts-express.sjv.io/LPADrM , (EU) bit.ly/3dS0Sm2
- 0.5m (2 feet) of speaker wire (14 AWG) - (US) parts-express.sjv.io/e4yRJz , (EU) bit.ly/39erRI4
- Lepai LP210PA 2x30W + 60W 2.1 Channel Mini Plate Amplifier TPA3118 with Power Supply - (US) parts-express.sjv.io/15nb36 , (EU) bit.ly/3xhgirU
- 24V 4.16A Power Adapter - (Arylic) bit.ly/2WuRBeR , (EU) bit.ly/2TNxB6o
- Polyester Batting - amzn.to/3bJfBhF , (EU) bit.ly/3ojxWYE
- Felt/Rubber Stick-on Pads - amzn.to/3id20kq
- Electric Wireless Solder Iron 5s Rapid Heating 30W or 50W USB Charging Lithium Battery - Banggood - www.banggood.com/custlink/GGv..., Parts Express - bit.ly/346drWn
Join this channel to get access to perks:
- / @soundblab
OR
- Become a Patron - / soundblab
Support SoundBlab:
- Subscribe to my channel - goo.gl/EWMSXV
- SoundBlab Website and Build Plans - www.soundblab.net
Follow me:
- Instagram: / soundblab
- Pinterest: / soundblab
- Twitter: / soundblabs
OTHER CHANNELS:
- Mixtape // Music for everyone and every occasion - bit.ly/3Cg3pUA
Recommended Gear, Tools, Amplifier Modules, Speaker Drivers, and more...
www.amazon.com/shop/soundblab
Audio Components & Solutions:
- Parts Express (US) - parts-express.sjv.io/yRNVk2
- Soundimports (EU) - bit.ly/3B0xWEn
- Axiomedia (EU) - bit.ly/3TUQUoA
Music: www.epidemicsound.com/referra...

КОМЕНТАРІ: 211
@SoundBlab
@SoundBlab 3 роки тому
The BUILD PLANS for this project can be purchased here: bit.ly/30u4d5a . It includes a comprehensive 28 page description of materials, parts, etc. on how to build this subwoofer from beginning to end.
@nvdwalt
@nvdwalt 3 роки тому
Awesome job bud. All straight cuts and easy to do. Love the top plate as well
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@NeyBar
@NeyBar 3 роки тому
Amazing absolutely neat!
@etiennelotriet4000
@etiennelotriet4000 3 роки тому
I absolutely LOVE this😂 Definitely going to follow this guide step by step! Thanks so much for the great video and detailed guide to follow! Links help a lot too- thank you!
@SoundBlab
@SoundBlab 3 роки тому
Glad it was helpful!
@jdmccorful
@jdmccorful 3 роки тому
Throughly enjoyed watching the build.
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@kithmalkalhara4329
@kithmalkalhara4329 3 роки тому
The work is beautiful and tidy. Congratulations!
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@xanderguldie
@xanderguldie 3 роки тому
It's like watching Bob Ross paint. Excellent work. Btw, those drivers are crazy good for their size.
@SoundBlab
@SoundBlab 3 роки тому
Thanks 👍
@jimthvac100
@jimthvac100 Рік тому
I became a subscriber when I watched your video on the DIY Ported Subwoofer Build. Very impressed with the use of the router. You make beautiful speaker cabinets. I like the soft edges of the majority of your cabinets as they will resist chipping. Your speakers sound good too. I also was not aware of these miniplate amplifier/crossover boards that you install in some of your subwoofers, So I am grateful for the knowledge of them.
@SoundBlab
@SoundBlab Рік тому
Thank you very much!
@FreshLeaves
@FreshLeaves 3 роки тому
Looks so beautiful and neat in the minimal design. Waiting for the next video.
@SoundBlab
@SoundBlab 3 роки тому
Thanks a lot 😊
@FreshLeaves
@FreshLeaves 2 роки тому
@@SoundBlab Will it make any difference if I switch the position of the sub from bottom to the front and using the same enclosure dimension?
@user-xb4nn6ql5l
@user-xb4nn6ql5l 3 роки тому
beautifully done your work is impeccable.
@SoundBlab
@SoundBlab 3 роки тому
Thank you very much!
@emiel333
@emiel333 3 роки тому
Wow, great job. You sure have skills building your own speakers. Very cool!
@SoundBlab
@SoundBlab 3 роки тому
Thank you very much!
@emiel333
@emiel333 3 роки тому
SoundBlab You’re welcome 😉
@msmith2961
@msmith2961 3 роки тому
The perfectionist in me wanted the amp plate to be flushed into the panel.. Great build though and looking forward to part 2!
@berklynelectronics
@berklynelectronics 3 роки тому
Same thoughts brother
@AudioElectronicsChicago
@AudioElectronicsChicago 3 роки тому
Interesting to watch, making it from a scratch to a subwoofer
@SoundBlab
@SoundBlab 3 роки тому
Glad you liked it!
@ChiaSeDamMeDIY
@ChiaSeDamMeDIY 3 роки тому
It's great ... it's been a while since I saw you on the video, good health & lots of fun 👍👍👍👍👍
@SoundBlab
@SoundBlab 3 роки тому
Thanks!
@kai_s.5177
@kai_s.5177 3 роки тому
Amazing work!
@SoundBlab
@SoundBlab 3 роки тому
Thanks a lot!
@myturkishlife1777
@myturkishlife1777 3 роки тому
@9:00 I thought you were doing this freehand ,,, until I saw the bearing cutter.. Nice job ....
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@travelunboxreviewfamily780
@travelunboxreviewfamily780 2 роки тому
awesome built!
@SoundBlab
@SoundBlab 2 роки тому
Thanks!
@kalaik5949
@kalaik5949 2 роки тому
Wow nice 👏👌 .From 🇮🇳 India
@SoundBlab
@SoundBlab 2 роки тому
Thanks
@Knkasiatic
@Knkasiatic 3 роки тому
good job, very inspiring,......greetings from Indonesia
@SoundBlab
@SoundBlab 3 роки тому
Thank you very much!
@nanhsi1
@nanhsi1 2 роки тому
Nice professional look
@SoundBlab
@SoundBlab 2 роки тому
Thanks!
@SubhanToba
@SubhanToba 3 роки тому
O master please take me as your apprentice. You're so skillfull in woodworking!
@yttean98
@yttean98 3 роки тому
It helps when you have all the equipment at hand. I am afraid too many steps, and pieces to cut and put together for me. Should sound good.
@ashyouknow7420
@ashyouknow7420 3 роки тому
Yeah exactly
@remyterjanian8602
@remyterjanian8602 3 роки тому
Looks and sounds awesome! I'm always impressed by your consistently improving production quality.
@SoundBlab
@SoundBlab 3 роки тому
Thank you very much!
@colinduv1644
@colinduv1644 3 роки тому
Awesome👍🤩!
@SoundBlab
@SoundBlab 3 роки тому
Thanks 🤗
@marliedpahltr6574
@marliedpahltr6574 3 роки тому
Very good job !
@SoundBlab
@SoundBlab 3 роки тому
Thanks a lot!
@HNIZAR45
@HNIZAR45 3 роки тому
Nice work
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@Mr11mukesh
@Mr11mukesh 3 роки тому
Satisfying video
@SoundBlab
@SoundBlab 3 роки тому
Thank you
@khushizindagi8987
@khushizindagi8987 3 роки тому
Super, excellent
@SoundBlab
@SoundBlab 3 роки тому
Thank you very much
@joseacuna3882
@joseacuna3882 3 роки тому
Hi sir im your new subscriber i enjoy your work , watching here from the phillippines
@SoundBlab
@SoundBlab 3 роки тому
Thanks for subbing
@piotrekhunt2440
@piotrekhunt2440 3 роки тому
what software do you use to create such cool stuff?
@anandgupta6838
@anandgupta6838 3 роки тому
sound very good
@SoundBlab
@SoundBlab 3 роки тому
Many thanks!
@mje3055
@mje3055 3 роки тому
you're the man
@SoundBlab
@SoundBlab 3 роки тому
Thanks!
@jimthvac100
@jimthvac100 Рік тому
What ended up being the final frequency response of this subwoofer?
@khiladi7770
@khiladi7770 3 роки тому
i can make box ..but i don't know where to buy all system for complete music system
@audiolab5612
@audiolab5612 3 роки тому
Very nice brother
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@nomekabau3408
@nomekabau3408 3 роки тому
Wow, , it so cool
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@ximonx
@ximonx 3 роки тому
Quick tip: don't solder wire ends that are going into solder terminals, the solder can migrate and you'll end up with loose wires 👍
@SynZ777
@SynZ777 3 роки тому
I've been wiring pots like that for years and I haven't had an issue with it.
@colouredcanvaswithsubhanka58
@colouredcanvaswithsubhanka58 3 роки тому
I'm also making a 2.1 boombox bt multimedia portable speaker... But i don't have a single powertool like power drill, power saw etc... It is on the way right now... If you would like to see what i am doing then it will be gladly appreciate for me... You are too good... Love from india...
@ivander1511
@ivander1511 3 роки тому
Nice sub
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@Acoustic_Theory
@Acoustic_Theory 3 роки тому
Another day, and another 6.5" Tang Band project. We need some new tiny subs, and the Tang Band subs leave some big shoes for any new driver design to fill.
@SoundBlab
@SoundBlab 3 роки тому
Yeah for sure. I would love to see another manufacturer come to the table here.
@tankdriver23
@tankdriver23 3 роки тому
I would round the edges in the tunnel.
@LuannRoxEcko
@LuannRoxEcko 3 роки тому
Seus sons são perfeitos
@SoundBlab
@SoundBlab 3 роки тому
Tx
@bhagwansinghrana8224
@bhagwansinghrana8224 4 місяці тому
Plz tell me the dimentions of sealed enclosure box for one 12 inch, 2000 watts rms sub woofer ?
@Tonygarz
@Tonygarz 3 роки тому
I wonder if it would of made a difference if he turned it into a 4th order box with that bass radiator facing the ground when sub box sitting right side up probably would of gave it some extra low sounds either way great build my dude 👍
@modernbassheads5051
@modernbassheads5051 2 роки тому
4th orders don’t magically play lower than bass reflex boxes… dunno where you’re getting your information from bro
@royservice
@royservice 3 роки тому
Good 👍👍
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@agungade_1973
@agungade_1973 3 роки тому
The information is useful
@SoundBlab
@SoundBlab 3 роки тому
Glad you think so!
@wesselw.7801
@wesselw.7801 3 роки тому
Very solid and clean build. Your woodworking is really sophisticated and delicate. Got a question tho, what software do you use to calculate your enclosure and port size? Looking forward to the soundbar build. Thx for the extra effort of filming your creations and posting them on yt :)
@SoundBlab
@SoundBlab 3 роки тому
Thanks. I used WinISD to determine the enclosure and port size.
@robson_uk
@robson_uk Рік тому
This is absolutely great design, and Im gonna do very similar one. But question is this amp enough for for this little fella?
@SoundBlab
@SoundBlab Рік тому
The amp does a really good job. I don't think it needs more power.
@Fcoiltamar
@Fcoiltamar 2 роки тому
Perfeito muito bom
@SoundBlab
@SoundBlab 2 роки тому
Thanks
@manjulwalia1995
@manjulwalia1995 3 роки тому
bro amazing build :) ... i watch all your videos .. specially the entire video without any skip when you use great music in the background... by the way , the sanding sealer you used , was it water based , oil based or laquer based ? also how many coats you applied ?
@SoundBlab
@SoundBlab 3 роки тому
Thanks! I think it is a lacquer based sealer. I normally apply 2 coats with sanding in between.
@chimpunkofficial4117
@chimpunkofficial4117 2 роки тому
Make two of these then put on right and left it Will make deeper and Slam impact and presure of bass
@SoundBlab
@SoundBlab 2 роки тому
two will be great!
@chimpunkofficial4117
@chimpunkofficial4117 2 роки тому
@@SoundBlab yupp
@alissonabello
@alissonabello 3 роки тому
Amigo cuantos parlantes, si hizo 2orificios i solo coloco 1
@Jan-nd1hv
@Jan-nd1hv 9 місяців тому
May i ask yoou what the function of the white cotton mesh you put inside?
@SoundBlab
@SoundBlab 9 місяців тому
It's a damping material that helps to break up any standing waves that we get inside the enclosure. It also reduces sound waves reflecting back onto the back of the woofer cone. All this helps to 'clean-up' the sound coming from the subwoofer.
@Jan-nd1hv
@Jan-nd1hv 9 місяців тому
@@SoundBlab Got it, so its let us to hear the 'solid' or 'pure' sound that came out from the cone
@raizada500
@raizada500 3 роки тому
How made a 2.1 channel computer speaker with 25 hz bass
@thecanadianace
@thecanadianace 3 роки тому
None of these build links seem to work for me
@jasper20017
@jasper20017 3 роки тому
Nicely done. Are you using a brad nailer or a finish nailer?
@SoundBlab
@SoundBlab 3 роки тому
Thanks. Brad nailer
@user-lq6nz1yx9h
@user-lq6nz1yx9h 3 роки тому
прикольная фреза по дереву
@mje3055
@mje3055 3 роки тому
very nyce
@SoundBlab
@SoundBlab 3 роки тому
Thanks
@springbokmarine
@springbokmarine 3 роки тому
Great video! Does the Amp need more ventilation? It seems that there’s no airflow around the electronics.
@wesselw.7801
@wesselw.7801 3 роки тому
I agree that normally a bit of ventilation would be usefull. However, I feel like this amp is not likely to overheat any time soon, since it is a highly efficient and relatively low power class D amp. I reccon that the little heat the amp might generate, will not be enough to cause any issues. Furthermore, the chip will also be cooled by the aluminium backplate.
@p_mouse8676
@p_mouse8676 3 роки тому
@@wesselw.7801 unfortunately I have seen the opposite from a lot of people with this particular amp. It overheats very quickly. Not very reliable.
@wesselw.7801
@wesselw.7801 3 роки тому
@@p_mouse8676 Are you certain that they had the amplifier setup correctly? The chip has an efficiency of 90% which makes it put out very little heat if it is used correctly. It seems to be quite an uncommon issue in online reviews so it might be possible that it was setup incorrectly, maybe a lower than 4 ohm impedance. If not, maybe they got a faulty one?
@p_mouse8676
@p_mouse8676 3 роки тому
@@wesselw.7801 They had the amp running free air even. And 90% seems a lot, but that is still not 100%. More over, the PCB design is just really poor, and mostly the inductors on it are WAY to small. (I design amplifiers myself fyi)
@wesselw.7801
@wesselw.7801 3 роки тому
@@p_mouse8676 Hmm, well will see of the amp holds up in this configuration :b. Btw cool that you are designing amplifiers :). If I might ask, what is your opinion about the kab250v3 and the dspb250 from dayton audio? I reccon they are cool little boards, but do you have any knowledge about any flaws?
@sanjeeevsinha
@sanjeeevsinha 2 роки тому
Can I get this and price pls
@kumarrupesh4556
@kumarrupesh4556 3 роки тому
I want to purchase this sub how to buy n where from i buy this sub.
@RIOTSBOYS
@RIOTSBOYS 4 місяці тому
@bloomerb4162
@bloomerb4162 7 місяців тому
I'm interested in building a 6.5 sub enclosure for the best sound quality. Tight bass, no boomy sounding bass. Would it just come down to how rigid the enclosure is?
@SoundBlab
@SoundBlab 6 місяців тому
A rigid enclosure is critical for a subwoofer, however the enclosure must also be designed and modelled well with software. Too small and it can be come boomy at higher low frequencies, and also limit the output at the lower end. Too big and you can again loose output at the lower end. The size of the vent, if going with a bass reflex enclosure is also going to determine the outcome. Too small of a vent can cause port chuffing as the air moves through it. So there are many factors to consider for a good subwoofer enclosure design.
@bloomerb4162
@bloomerb4162 6 місяців тому
@SoundBlab after all those factors are taken into account, then rigidity? I've always heard the more rigid you can get the enclosure, the better or tighter the bass will be.
@FreshLeaves
@FreshLeaves 2 роки тому
@SoundBlab Will it make any difference if I switch the position of the sub from bottom to the front and using the same enclosure dimension?
@SoundBlab
@SoundBlab 2 роки тому
You can do that. It will perform the same.
@FreshLeaves
@FreshLeaves 2 роки тому
@@SoundBlab thankyou
@MegaMartico
@MegaMartico Рік тому
Nice work where are you based?
@SoundBlab
@SoundBlab Рік тому
Thanks. Cape Town
@adamdjd7882
@adamdjd7882 2 роки тому
How does the sub plug into the arylic? I've bought plans for the soundbar design, but already have a sub to use Thanks mate
@SoundBlab
@SoundBlab 2 роки тому
I use the line output from the Arylic to plug into the sub, which is a 2.1 plate amp.
@adamdjd7882
@adamdjd7882 2 роки тому
@@SoundBlab thanks for getting back so fast, by line out are you referring to speaker cables that run to the subwoofer or is there an RCA connection that I can't see on the board? ( as that's what I'm used to connecting a subwoofer with. )
@p4nget
@p4nget 3 роки тому
I want to make may yamaha 5.1 into a soundbar. And rebuild its subwoofer box.
@krisandersson7156
@krisandersson7156 3 роки тому
Cool build but that port looks dangerously small. Port Noise?
@todd_drums
@todd_drums 3 роки тому
For a 6.5" driver that seems like enough port area, it is fairly wide. And it also probably helps achieve a lower port tuning.
@SoundBlab
@SoundBlab 3 роки тому
It actually does not create any port noise, even at full volume. I made sure to look at this when I was modelling the enclosure in software.
@mrdawgza
@mrdawgza 3 роки тому
Do you source your speakers locally in SA or are they all imported?
@SoundBlab
@SoundBlab 3 роки тому
all imported
@thearnavsmusicworld3822
@thearnavsmusicworld3822 3 місяці тому
Can we connect speakers on this .
@SoundBlab
@SoundBlab 3 місяці тому
If you use the recommended plate amp, then yes. You can create a 2.1 system.
@yuvarajduraiswamy8135
@yuvarajduraiswamy8135 3 роки тому
What 3D CAD u are using
@SoundBlab
@SoundBlab 3 роки тому
I mostly use SketchUp and sometimes Fusion 360.
@agrooberli
@agrooberli 3 роки тому
Why when you finish a video you say goodbye with a adiós in Spanish?, it's one thing that intrigues me ^^
@SoundBlab
@SoundBlab 3 роки тому
There is no particular reason, it's just something I do.
@radiospank
@radiospank 3 роки тому
Seemed unnecessarily complicated for a sub box. Could’ve used 3/4 inch plywood and skipped internal bracing. Also that port looked super tiny, what velocity is that pushing at max volume?
@SoundBlab
@SoundBlab 3 роки тому
Of course you can use a thicker material, but bracing eliminates the need for that. Even with 3/4 inch I still think bracing will be a good idea. The port was modelled to avoid any chuffing that might occur at higher volumes. You can pump this to its max, and still not hear any chuffing from the port.
@r.jwilliams3173
@r.jwilliams3173 3 роки тому
are you from South-Africa sir
@SoundBlab
@SoundBlab 2 роки тому
Yes
@babluvlog7553
@babluvlog7553 2 роки тому
Plz box size
@dontangryman1122
@dontangryman1122 2 місяці тому
Sir I build to my subwofer to you macking for you
@sibinkvargheese8519
@sibinkvargheese8519 3 роки тому
What is the height you given for sub woofer box..??
@SoundBlab
@SoundBlab 3 роки тому
400mm
@dieselsmiths
@dieselsmiths 3 роки тому
Oh that sounded great?
@peterphoku55
@peterphoku55 2 роки тому
Hi where can I get the subwoofer board
@SoundBlab
@SoundBlab 2 роки тому
link in the description of the video.
@mr.rajeshparia8080
@mr.rajeshparia8080 3 роки тому
How can I buy this product? I'm from india. Any online website available for buy this product?👍
@SoundBlab
@SoundBlab 3 роки тому
I only sell build plans , not the actual product on my website soundblab.net.
@MRsm-vf9cn
@MRsm-vf9cn 3 роки тому
Look like music instrument cajon
@keztutiz
@keztutiz 3 роки тому
Great sub mate!! Well done! 3:26 song is? :)
@SoundBlab
@SoundBlab 3 роки тому
Thanks! I get my songs from epidemicsound.com, so not sure what track this is, I don't really keep track of the tracks I download, sorry man!
@keztutiz
@keztutiz 3 роки тому
@@SoundBlab ok no worries :) keep up the good work :)
@sachinzachy
@sachinzachy 3 роки тому
Pls tell me, is a 5 inch sub is good for making a home theatre
@UhOhUmm
@UhOhUmm 3 роки тому
The smaller it is the worse it is. You generally want your subwoofer to only produce sound up to 80-100Hz because then it's hard to tell where the sound is coming from. 5 inch sub is very small and it will be making sounds when you don't want your sub to make any sound, like males with deep voices speaking. For home theatre speakers 6.5 inch subs with sound bars are the bare minimum I would go to and even those are often borderline. My bookshelf speakers have 6.5 inch midrange drivers for example and I have 10 inch sub to match them, which is still considered small in home theatre standards.
@sachinzachy
@sachinzachy 3 роки тому
@@UhOhUmm thanks for your words, opinion from an experienced person is more helpful to me
@SoundBlab
@SoundBlab 3 роки тому
If you have small speakers or even a sound bar to pair it with in a very small room you could get away with it, but generally I would not recommend it. Would be better if you still want to go that way, is to use two 5 inch drivers not just one. A 5 inch driver will also not give you much output below 35Hz. So it all depends on the application.
@ItsDank
@ItsDank 3 роки тому
you make an entire video about this and we dont even get to hear it god damn
@sekphokham4117
@sekphokham4117 2 роки тому
Ask for a wood cutting form (recipe) thank you.
@SoundBlab
@SoundBlab 2 роки тому
Check the build plan in the description.
@nomnommonsterr
@nomnommonsterr 2 роки тому
What is the Fe value of this?
@SoundBlab
@SoundBlab 2 роки тому
Don't know what Fe is, but the Fb or -3dB point of the response lies at roughly 35Hz.
@nomnommonsterr
@nomnommonsterr 2 роки тому
@@SoundBlab de I mean. Damn. 36Hz is very good for the size.
@nomnommonsterr
@nomnommonsterr 2 роки тому
@@SoundBlab 35 i mean.
@wolf-dietermanzke9233
@wolf-dietermanzke9233 Рік тому
Wo ist der Stromanschluß für die Endstufe? Wolf-Dieter Manzke
@SoundBlab
@SoundBlab Рік тому
It has a 12v power socket on the back of the plate amp. It connects to an external power supply.
@anesloudspeakers1960
@anesloudspeakers1960 2 роки тому
👍
@SoundBlab
@SoundBlab 2 роки тому
👊
@dontangryman1122
@dontangryman1122 2 місяці тому
I form to Indian 🇮🇳
@Luis-Tesla
@Luis-Tesla 3 роки тому
Que simple lo hace
@chakireladraoui9331
@chakireladraoui9331 3 роки тому
♥ ♥ ♥ ♥ ♥ ★ ★ ★ ★ ★
@thomasschafer7268
@thomasschafer7268 2 роки тому
85€ for only 6inch ?
@CesarPeron
@CesarPeron 2 роки тому
You didn't show us the sound check...
@SoundBlab
@SoundBlab 2 роки тому
Go look at the soundbar video.
@BUZDRIFT
@BUZDRIFT 3 роки тому
This little thing will struggle in the lower frequencies and even the 30's might have significantly low output ...?!
@__-fm5qv
@__-fm5qv 3 роки тому
It'll probably be fine down to the mid 20's or so, the smaller 5.25" version of this woofer can managed mid 30's just fine.
@BUZDRIFT
@BUZDRIFT 3 роки тому
@@__-fm5qv Hmm! I doubt they'd be much output at the lower frequencies compared to it's sweet spot of 60-80hz with a 6.5". I'm sure it can play 20hz and 30hz but how much output does it loose?
@__-fm5qv
@__-fm5qv 3 роки тому
@@BUZDRIFT Well the 5.25" version I have is playing down to 37hz at -3db. These drivers are pretty much exclusively designed to go deep, but at the sacrifice of overall sensitivity and some reponsiveness/tightness.
@BUZDRIFT
@BUZDRIFT 3 роки тому
@@__-fm5qv Yeah, that's actually pretty good for such a small driver! Damn!
@newsksameerstatusvideo4036
@newsksameerstatusvideo4036 3 роки тому
M. R. P Kay hai
@BrenttttttMCMXC
@BrenttttttMCMXC 3 роки тому
looks like it will last for 10 years
@SoundBlab
@SoundBlab 3 роки тому
I hope so!
@saneeshgoldentoy5029
@saneeshgoldentoy5029 3 роки тому
Plz 12inch sub box
@saneeshgoldentoy5029
@saneeshgoldentoy5029 3 роки тому
Measurement And detail
@debabratapal516
@debabratapal516 3 роки тому
Where is sound test ???
@SoundBlab
@SoundBlab 3 роки тому
Next video after this one where I build the soundbar that goes with this sub.
@jestersantillana4872
@jestersantillana4872 2 роки тому
What amplifier you are using bro? I want to buy also
@SoundBlab
@SoundBlab 2 роки тому
There should be a link in the description
@ramabargawa9678
@ramabargawa9678 3 роки тому
Kok gak di cek sound
Building a SOUND BAR V2.0 - Speaker Build - by SoundBlab
24:15
SoundBlab
Переглядів 296 тис.
Building a Small Ported Subwoofer - by SoundBlab
21:15
SoundBlab
Переглядів 219 тис.
The Great Subwoofer Debate: Ported vs Sealed - Which Sounds Better? KICKER Comp Gold
11:25
You should use a SMALLER SUBWOOFER! 5 Reasons WHY!
7:50
CarAudioFabrication
Переглядів 622 тис.
【DIY】 Homemade Wooden Speakers | Sound AMAZING Part.2
15:02
Gonta DIY
Переглядів 667 тис.
Building a 4" Transmission Line Subwoofer - by SoundBlab
8:49
SoundBlab
Переглядів 776 тис.
Is a Deep Speaker Box Better? Tested with Surprising Results
6:04
John Heisz - Speakers and Audio Projects
Переглядів 220 тис.
Bandpass Subwoofer: You Are Doing it Wrong.  Bandpass MYTHS BUSTED!
12:11
DIY Audio Guy
Переглядів 461 тис.
Mini Bandpass Enclosure Series - Full Build Plans and Demo!
46:13
BudgetBassHead
Переглядів 114 тис.
Building EXCEPTIONAL speakers using MODERN TECHNIQUES
22:20
DIY Perks
Переглядів 3,2 млн
Coca Cola Donması
0:34
TeknoFinans
Переглядів 6 млн
Находка для розыгрышей с вайлдберриз озон #wb #shorts
0:15
Playing This On Loop ♾️
0:27
Red Bull
Переглядів 56 млн
Surprise Gifts #couplegoals
0:21
Jay & Sharon
Переглядів 15 млн