DIY 5.1 Amplifier
Переглядів 44,854
2 роки томуToday I am going to show you how to make DIY Powerful 600Watts 5.1 Amplifier using TDA3116 Amplifier module which produces 100 Watts per channel output.
Check out my instructables page for LED Ring light Circuit diagram :
Link: www.instructables.com/8-Bit-L...
Components /Materials used :
Links Available in my instructables page
Uploading soon....
------------------------------------------------------------------------------------------------------------------------
⚠️ Disclaimer: We are not responsible for any kind of damage or loss, do everything at your own risk.
-------------------------------------------------------------------------------------------------------------------------
🎵 Music in this Video:-
------------------------------
Track: Coast - Declan DP [Audio Library Release]
Music provided by Audio Library Plus
Watch: • Coast - Declan DP | Fr...
Free Download / Stream: alplus.io/coast
------------------------------
Jazzaddict's Intro by Cosimo Fogg (201)
/ cosimo-fogg Creative Commons - Attribution 3.0 Unported- CC BY 3.0
Free Download / Stream: bit.ly/jazzaddicts-intro
Music promoted by Audio Library • Jazzaddict's Intro - C... ------------------------------
Track: I Am OK - Vishmak [Audio Library Release]
Music provided by Audio Library Plus
Watch: • I Am OK - Vishmak | Fr...
Free Download / Stream: alplus.io/i-am-ok
------------------------------
Track: Altitude - Declan DP [Audio Library Release]
Music provided by Audio Library Plus
Watch: • Altitude - Declan DP |...
Free Download / Stream: alplus.io/altitude ------------------------------
Video Tags:
#Techrally #tech #rally #5.1 Amplifier
@AswanthSharman 6 місяців тому
Can u explain which one is the subwoofer out and how many watts actually it is?
@videopendek2421 2 роки тому
this is an interesting video , very recommendation to watch
@TechRallyofficial 2 роки тому
Thank you 😊
@diytricks7234 Рік тому
Nice work, I did a similar project, you may need a fan if you want to reach the full potential of those boards at 24V the heatsink is not sufficient.
@TechRallyofficial Рік тому
Great, yes fan adding fan will be a better option 👍 😀
@lunarz7117 2 роки тому
I feel using a arduino micro just to run an ARGB led ring light is kind of wastefull, so many pins are not used! Maybe program an AtTiny85 for just running the ARGB leds?
@TechRallyofficial 2 роки тому
Yes, Using Arduino Pro Micro just for ARGB LED is not cost efficient, you can use any cheaper Arduino boards..😀 Thanks for watching...😉
@yogeshsinghsonigra4054 Рік тому
You can program alexa in Arduino
@TechRallyofficial Рік тому
That is not possible bro..
@supratimmondal5071 10 місяців тому
You have done a great job keeping everything clean and organized. Kudos, and keep it up! 🤍
@TechRallyofficial 10 місяців тому
Thank you 😊...
@parthasarathimanna8790 2 роки тому
Nice ! What's that thing of boAt you used?
@TechRallyofficial 2 роки тому
Thanks, It's 3.5 mm audio cable
@GeoBass-89 Рік тому
nice work. i like how you pay atention but... you need for that 5.1 amplifier few things : 1: power supply is not enough even for one chanel . you need 24v power supply and 15A minimum 2: you need some active filters there for each chanel in specialy subwoofer you will habe a big improve sound better than much home theaters 5.1
@TechRallyofficial Рік тому
Yes, selecting a right power supply is important based on application and speaker ratings, for me 12v 5A is enough for small room you won't believe me it works really well i haven't seen any issue with it ,since its a Class D amplifier it is very power efficient, I am using only for desktop 5.1 output which has built in active filter so passive filter is not mandatory but adding it improves quality.
@GeoBass-89 Рік тому
@@TechRallyofficial yes, but if you put bigger power supply you Will improve much quality sound. Good job anyway
@TechRallyofficial Рік тому
Thank you 😊
@kayjay4561 Рік тому
There are no links in the description for the parts you used to make this? Though the video mentions that such links would be in the description? Can you provide those links as a comment, maybe? Thanks. This is an awesome project.
@TechRallyofficial Рік тому
I will update and comment here Thanks
@kayjay4561 Рік тому
@@TechRallyofficial Thanks. In the mean time, would it be possible to provide either a link or the specific brand name for the 100k 6 gang potentiometer you used in the video?
@TechRallyofficial Рік тому
The one i used was not available online in India now, i brought it on aliexpress below is alternate component MASTER TYPE 100K ohm 6 gang potentiometer amzn.eu/d/bjp4KsY
@kayjay4561 Рік тому
@@TechRallyofficial I can't find this where I live, so I am going to do something like this - ukposts.info/have/v-deo/jJt6jXuhiZpn0pc.html. Do you think this will work? Thanks.
@TechRallyofficial Рік тому
Even small force could damage the carbon in potentiometer, its not worth the effort also volume control will be uneven. Try local amplifier shops to get. If you have access to aliexpress in your country it will be better option to get from there...
@die3ddrucker 5 місяців тому
Sub ❤ nice work! Keep it up
@TechRallyofficial 5 місяців тому
Thank you 😊
@rohitjasuja.mumbai 9 місяців тому
Can you make a 7.1 with audiophile components having 100 watts output per channel at 8 ohms? To make it interesting we can add the ESS9038Pro DAC board also in the unit. I can pay for the entire setup and your expertise.
@TechRallyofficial 9 місяців тому
Sorry currently i am not doing this service, may be i will try in future, Thank you 😊
@jacky_cola 2 місяці тому
Hello, I have a Question. I have tried a very similar setup, but whenever I try to plug in 2 cables there will be humming/buzzing nosie. The sound will work but the noise is very loud? What can it be and how to prevent that?
@TechRallyofficial 2 місяці тому
This might be because of your SMPS power supply or poor grounding loop in your audio source. Try reducing the gain in amplifier board potentiometer. And make the audio cable doesn't interfere with other display or power cables.
@ixrvalor0812 Рік тому
i have a question , please answer me, if i have 3 amplifiers like that need 19v 4amp per amplifier, can i use all three in only one 19 v adapter
@TechRallyofficial Рік тому
Class D amplifiers are high power efficient You can use all 3 in one Adaptor, If you use high power drives for all channels you may require high power Adaptor.
@ixrvalor0812 Рік тому
@@TechRallyofficial my question is if i have 19 v adapter 9amp , will the 9 amp divide by 3 for the 3 amplifiers or every each one will get 19v 9amp
@TechRallyofficial Рік тому
Power will be divided based on load.
@yogeshsinghsonigra4054 Рік тому
Current will get divide in all three amplifier, each one will receive 19v 3 ampere
@sreejasajeev-artsandlifest8321 2 роки тому
Bro, i have made a similar project., But i am not getting enough bass while playing films with vlc, 123player etc. The bass i am getting is very low ( from center/SW port ). Do you know what must be the problem?
@TechRallyofficial 2 роки тому
This a common problem with PC audio output, you need have the realteak audio driver and in that you need to enable Bass management and enable room correction in that increase the gain for subwoofer.. THANKS...😊
@sreejasajeev-artsandlifest8321 Рік тому
@@TechRallyofficial . Bro it worked⚡⚡⚡⚡. Thank you soo much 🥰
@TechRallyofficial Рік тому
Super bro..✌
@diytricks7234 Рік тому
I think it depends on the sub you are using, normally the PC should be able to generate the required signal
@MdRipon-tx7dv Рік тому
Can you give me master volume wirings diagram???
@TechRallyofficial Рік тому
Below the link for 2 channel, same method us can use for all 6 channels, refer the image in link, techtalk.parts-express.com/forum/tech-talk-forum/58484-adding-volume-potentiometer-to-amplifier-board
@rawgen Рік тому
Do you use 5 amps? How you set the control to center and subwoofer canals in a single dual channel amp board?
@TechRallyofficial Рік тому
Yes, i use 5A power supply The board has the gain control for each channel, using that u can control center and subwoofer channel separately...
@rawgen Рік тому
@@TechRallyofficial and 5 boards?
@TechRallyofficial Рік тому
Each amplifier module has 2 channel, so you need only 3 module for 5.1 ch output
@francisxavier5084 4 місяці тому
is it not TPA3116?
@TechRallyofficial 4 місяці тому
Its TPA3116
@simtcr Рік тому
can you please explain what does that large potentiometer for ?
@TechRallyofficial Рік тому
For Master volume control..
@simtcr Рік тому
@@TechRallyofficial I did not understand the wiring of it, do you mind sending a diagram or explain it here please?
@TechRallyofficial Рік тому
The large potentiometer is called as gang potentiometer its just ah noramal potentiometer group to geather to control all 6 channels volume to geather, its actually a group of 3 potentiometer containing 6 pin each below the link for 2 channels control refer the image in link, techtalk.parts-express.com/forum/tech-talk-forum/58484-adding-volume-potentiometer-to-amplifier-board
@simtcr Рік тому
@@TechRallyofficial thank you, in my case, I only have one amp board (same board as yours) which I want to control master volume. to INPUT SOURCE, does that mean the 3 pins on the amp where I will be connecting the Bluetooth audio player? to AMP channel (ch1 and ch2), does that mean where I connect the speaker from the amp?
@TechRallyofficial Рік тому
In that 3 pin one will be groud and other 2 pin will be input to amp, ground pin should be connected to the left side pin of potentiometer and other 2 pin will connected to the center pin in potentiometer and input audio source will be connected to right side pin of potentiometer..
@prathikguptha183 8 місяців тому
Hi can u make one for me? What’s the price?
@TechRallyofficial 8 місяців тому
Sorry i am currently not selling anything for now, i will try to do in future. Thanks 😀
@satyarai2190 Місяць тому
What's your 5.1 price if any buy this directly.
@TechRallyofficial Місяць тому
Sorry i am selling any thing currently.. Thanks 😀
@Dougftvc Рік тому
I am still waiting!
@dailydoseofkerala3155 3 місяці тому
So basically u are using your pc as a decoder.. Then amplifying each channel comming out from the pc.... Great job... But this can only give 5.1 out put if you have a pc with you....and also using aurdiuno for led was an overdoing. 😅😅
@TechRallyofficial 3 місяці тому
Exactly yes... Aurdino was lying in shelf for long time it needs some use..😝 Thank you 😊
@newgamersbuddy5136 9 місяців тому
Can you make it for me
@TechRallyofficial 9 місяців тому
Sorry currently i am no selling anything, but in future i will try. Thank you 😊
@karanmalhotra2603 Рік тому
Please reply brother , I have some work for you.
@TechRallyofficial Рік тому
How can i help you
@aswinsura3851 2 роки тому
12v 5 amps not at all enough.
@TechRallyofficial 2 роки тому
Its only class D amplifier, which will not cosume more power like transistor based amp, I am using this on daily basis so far i haven't seen any audio distortions.. Its recommended to use high power if you are using high power subs.. Thanks 😀...
@aswinsura3851 2 роки тому
@@TechRallyofficial what ever it is but that board is rated at 100w+100w and u have 2 of them which means total power consumption will be 400w if the efficiency is 100%.yes its class d chip which means that clipping feedback ckt and build in to it.if u connect 12v 1a will also work with out clipping but relative power output will significantly lower.
@TechRallyofficial 2 роки тому
100w is just a peak power it doesn't mean it consumes 100w at all time, Even if you use at high volume it consume only 40w max if you go maximum 100W than it is more that sufficient for even a big house and neighbours to complain about loud volumes. Selection of power supply is important also should be based on your application. Thanks...
@nvk1630 Рік тому
5.1 channels and 2.0 input. what are you doing?
@TechRallyofficial Рік тому
There is no 2.0 input, i used 3 amps each has 2 channel and 3 audio input jacks each 2 channel, 6 channel output form pc via 3 male to male audio jack cabe each 2 channel. This is pure 5.1 audio.
@nvk1630 Рік тому
Ok that good bro, but your connecting bluetooth only 2 channels.
@TechRallyofficial Рік тому
Oh ok now i got your point, just for demo i connected via mobile for 2 cannel, subwoofer + center speaker alone will work. That only for demo because i dont have 5.1 source to test on table, finally i connected to my pc for 5.1 source... Thanks
@nvk1630 Рік тому
@@TechRallyofficial you should use "HD Audio Rush" to decode at the input, and it is called one av receiver.
@creatinggaming7067 Рік тому
Sir hindi main banao aur jyada like milega try karke toh dekho ☺
@TechRallyofficial Рік тому
Sry, Can you please translate in English..
@sonucae Рік тому
@@TechRallyofficial sir he is saying "Please make videos in hindi language. you will get more views".
@sonucae Рік тому
Bro language is not barrier for such nice videos. video itself is self explanatory. (Bhai video bohot accha hai hindi english ki koi baat hi nahi hai ).
@TechRallyofficial Рік тому
Thanks bro for translation and support 😊
@mikecox05799asd Рік тому
you said its 600w. its no where close to that maybe 25w at best. thanks for being a liar.
@TechRallyofficial Рік тому
Sorry for not cleary mentioning, Peak power is different than power consumption, i used TDA3116d2 based amplifier boards which has total of 6 for each channel you can search in Google for power rating. I used 12v 5vamp power supply which is more than enogh for my home use since i have only small speakers.
@tejakesavaram5972 11 місяців тому
Good job! Bro how can I contact you I have some doubts
@TechRallyofficial 11 місяців тому
Thank You 😀, you can add your questions in comments section
Голос Америки Українською
Переглядів 443 тис.
Радіо Свобода
Переглядів 202 тис.
What I Think
Переглядів 107 тис.
ErCan Everything
Переглядів 1,3 млн
ON Power
Переглядів 6 млн
Notebook1 Ассоциация сервисных центров
Переглядів 57 тис.