We will check the strength of the end heads with a hydraulic press. Different price range, and made in different countries
КОМЕНТАРІ: 1 400
@jakubkrcmaРік тому
It would be nice if you put a comprehensive table at the end of the video. Prices, weights, dimensions, breaking forces and, most importantly, the price/force ratios.
@slipjones2Рік тому
Yes otherwise it’s really just a time wasting video
@gafranciscoРік тому
well u can do the table ... he put every data in there :)
@jakubkrcmaРік тому
@@gafrancisco Great idea... Do something for free that someone else gets paid for. 🤣
@davidjacobs8558Рік тому
that would make him the "Project Farm"
@savetheclimate2292Рік тому
@@gafrancisco He only showed the data on the material thickness for two of the socket wrench hads. I guess that it is this parameter to correlate the forces with. Not the price nor the weight.
@brinkwolf8813Рік тому
I sold and used tools for almost forty years and a lot of people don't understand the difference between impact and standard sockets. Impact sockets are not only thicker but softer material to take the pounding affect of the impact gun. Hard chrome sockets are designed for the torqueing while using a ratchet or breaker bar. Now not saying you can't use either in each others place(the hard socket will give quicker on a impact gun) but I've always heard people say they wanted the impact socket because it was the premium socket and the hard chrome was not. If you buy a premium socket no matter which one and use it as intended and take care of it it will last a long time.
@trexmidniteРік тому
It was probably slightly less hard but less brittle too and more accurate
@iway002Рік тому
👍👍👍good explanation!!
@user-fh2cv3ym2q7 місяців тому
Thank you now THATS REAL KNOWLEDGE...
@Anubis782506 місяців тому
Chrome sockets on an impact most often deform at the square section first, but also crack at the socket walls. I think I've split more chrome sockets with an 8 inch ratchet over the years than I've ever purchased, not to mention broken every breaker bar I've ever had. I switched to using exclusively impact sockets for anything 9/16 and up, and I can recall only once ever breaking one with a hand ratchet. I use a 40 year old proto ratchet as my breaker bar these days, no one makes a breaker bar that lasts more than a few uses.
@mikeb.6773Рік тому
1:34 The Bosch and Milwaukee sockets are both made in Taiwan. If you want to demonstrate a German made or USA made socket, then use brands that make sockets in those respective countries i.e. Gedore or SK Tools
@billythekid2281Рік тому
I’ve got a set of Gedore. Was used daily for 20 years. No breakages.
@chadd587Рік тому
SK or Wright are the only US made brands
@johnnycabraРік тому
I agree. US made brands would have been Proto, Mac Tools and Snap-On. Dont know any German brands but Czech tools would include Wera. This was basically cheap chinese socket vs multiple cheap Taiwanese sockets.
@mikeb.6773Рік тому
@@johnnycabra I would say cheap Chinese and slightly more expensive Taiwanese tools. And Taiwan produces some pretty good quality under brands that maintain good quality control. I also get that most home hobbyists don’t want to or can’t pay the price for the good made is USA brands, so buying Taiwanese at least still supports workers in a democratic free country. However I do trade work for a living so my tools are primarily SK, Williams and Wright with a smattering of stuff from Japan and Germany
@loucifer4205Рік тому
They always try push Milwaukee as American but unfortunately it hasn't been a American company for almost 20 years it's owned by China and their tools are made with slave labor
@SebastianEbel_19277Рік тому
No one in Germany would use Bosch manual tools... Hazet, Gedore, Stahlwille are famous and really high quality tools.
@ppdanРік тому
Agree, well at least for sockets and the bigger tools. For impactscrew driver they actually have great bit sets but that's a different range of tools.
@niklasoswald7937Рік тому
gedore is austrian isnt it?
@ppdanРік тому
@@niklasoswald7937 Nope, German
@tisto5016Рік тому
Bosch and würth build crap tools
@Akotski-ys9rrРік тому
Well Milwaukee tools are made in China so it’s even
@WXSTANGРік тому
Noname $4 - 3218kg Force Taiwan $5 - 5580kg Force Taiwan 6 face $5 - 6850kg Force Impact $3 - 12280kg Bosch Germany $17 - 7260kg Milkwalkie USA $5 - 11086kg OLD/Vintage socket - 4270kg
@sandiwijaya4964Рік тому
Noname $0.4
@boci11Місяць тому
as usual the bosch is overpriced and underperforming
@cesaravegah378722 дні тому
Thanks
@miwo22512 дні тому
Bosch made in Taiwan $15!
@jamesglavich1426Рік тому
I would think the true test of a socket, is the amount of torque it will withstand fastening and removing a bolt or nut. The tolerance between the socket size and the bolt head or the nut is pretty important. I would not base a purchase decision on this demo with the little hydraulic press.
@vasantos-re4hbРік тому
What people don't understand, it's not the socket, it's the nut. A nut gets rounded when too much torque is applied. The really nice sockets have a notch inside to grip the edges of a nut. An impact socket is actually softer metal that won't shatter under load.
@davidjacobs8558Рік тому
@@vasantos-re4hb I had a 30 year old Craftsman 18mm socket 12 sided for 3/8" ratchet. I never used it until few days ago, to remove a sway bar bushing bracket from a Mercedes. It cracked before the bolt got loose. So, I got out Craftsman 18mm long socket 6 sided for 3/8" ratchet. It cracked also. I went to Lowes to see if they are going to replace the socket for free, and they did. The new Craftsman 18mm socket I got from Lowes as a replacement did not crack, and was able to remove the bolt.
@K0nc3pt10nРік тому
@@vasantos-re4hb I've had a socket break on me, so that's what I wanted to see.
@stevanjakovljevic8390Рік тому
Great last name
@yspegelРік тому
This test is not relevant at all. A softer material with thicker wall would score better but what you want is a hard material with thin wall so you fit in more places and when it slips over a nut your tool is still good.
@hmcredfed1836Рік тому
As a technical draftsman and technician in mechanical engineering, I am not so sure about the usefulness of this test. The force applied to the top of the nuts/tools only, is very different from the force during use. Simply increasing the outside diameter would greatly improve these results, but the inside contour would still likely be destroyed at the same torque. Could you do a torque test to see when the tool shears off so the results show the actual forces during use of the tool. There is also a big difference between between impact and standard tools! greetings from germany
@Fiffo3639 місяців тому
This test is absolutely useless. Would be the same if cars were subjected to a diving test.
@bdweldmain7 місяців тому
Also elect/Mach engineer, what's not clear to me the force of forward/ reverse movement with coupling both ends of the test article and to what kgs will the bending points tested to accumulate the correct defective force of the subject in question, the formula pls to value your findings. Thanks
@Kr0nicDragon7 місяців тому
“Crush random stuff, get free patron money” there’s your reason
@gonzalohernanprieto74657 місяців тому
Totalmente de acuerdo, no entiendo que conclusión se quiere sacar
@davidbrayshaw35297 місяців тому
My understanding is that sockets are susceptible to stretching, with use, beyond the yield point of the material from which they are made. I think that the hydraulic press could be used to assess this, but only by measuring deformation of the sockets at various loads. The whole time that I was watching this presentation, I was wishing that a dial gauge had been set up to measure changes in the outside diameter of the socket. Destructive testing of this nature tells us very little, indeed.
@gruenherz54Рік тому
The wall thickness determines strength (along with the material). Thin walls are very desirable because there is often little space. To be a fair test you should do thickness/breaking force.
@torpedox-.001Рік тому
Impact sockets vs Standard "hand" sockets. Completely different requirements to design. Impact wrenches destroy thin walled sockets!
@shitloveaduckРік тому
@@torpedox-.001 - Very true!! Plus people use impacts incorrectly too often. They are nice to get things snug, but then trying to get the proper torque on something is the best way to fully tighten nuts & bolts. If there’s no torque listed, then have fun!! 😂😂. Used to be in a tire shop and they staff would screw up and get lazy or stupid or both. One or another would tighten the crap out of a wheel and we would get a towing bill because of when the client would get a flat or try to rotate the tires themselves and they couldn’t get the lug nuts off or kept on snapping them. I would teach the staff again how to do it right and see what happened later. I would spot check and then the good employees would ask if I didn’t trust them,,,, it’s hard! We did keep record of who worked on what and if there were 2 vehicles by the same person with a problem, one before the first training and a second problem after we taught them again, they were fired. They would have had ample warning and opportunity to do it right. We would lose one or two staff a year, just for that thinking they could estimate the torque they were applying!!! Haha. That’s life I guess. It happened pretty routinely for over 40 years!! 😂😂
@torpedox-.001Рік тому
@@shitloveaduck don't forget, a touch of never-sieze or assembly grease, will give the most accurate torque. And Worth it's weight in gold, ten years later, when you go to remove the the offending hardware! 40+ years of Electric Motor and Pump Service.
@shitloveaduckРік тому
@@torpedox-.001 - you are sooo correct! I am a big fan of the stuff!
@hrudaygolla3743Рік тому
Yo. Mr. Physics
@2889142Рік тому
As a Taiwanese, my last job was as an employee of a tool factory, and I am an OEM for the world's major brand products. I am proud of the fact that quality creates reputation and brings a safer use environment.
@no1strategicfooyouagency310Рік тому
Hello Chinese man !
@2889142Рік тому
@@no1strategicfooyouagency310 Taiwanese, not Chinese ukposts.info/have/v-deo/so-XjWenoWeHo6s.html ukposts.info/have/v-deo/nKJngoOeZ2xq2aM.html ukposts.info/have/v-deo/iHJlm3-baaOBr5c.html ukposts.info/have/v-deo/p5iona9tepyrqJc.html ukposts.info/have/v-deo/gqN9jKqinKRet3k.html ukposts.info/have/v-deo/mWdhbXiceoOTqpc.html
@Om0m007Рік тому
Taiwan and Tibet are different from China. #CKMKB
@user-nk8mz5ck2vРік тому
You're right
@ShivamCarboyРік тому
@@Om0m007 there's no such thing as China, it's called as West Taiwan
@jkgoogle5185Рік тому
Don't overlook the fact, the Bosch socket was a thin walled impact socket against the Milwaukee thick walled impact socket.. You're not comparing the same TYPE of impact sockets..
@michaelwhitmore7160Рік тому
most Bosch tools are made by third party , I am not impressed with many Bosch tools I have bought over the time .Electric tools are ok
@youtubetim3577Рік тому
Germany tools are trash either way now and days you pay for made in Germany but they always do poor in tests like China made products or worse... I remember when Germany tools were top notch, trash now.
@rediron44Рік тому
Milwaukee makes better tools..🇺🇸
@jkgoogle5185Рік тому
@@rediron44 Hazet makes better tools than Milwankee
@DrumSurgeryРік тому
@@rediron44 made in Taiwan indeed
@stevemoore445Рік тому
It’s nice to see that folks around the planet enjoy breaking stuff!!
@hugdamРік тому
Experimento interessante! Eu cheguei até a pensar que a soquete antiga ia ser mais resistente que as modernas...
@RobertooliversРік тому
Pensei a mesma coisa... fiquei surpreso com a pouca qualidade da Bosch e Millwalke em relação aquele Force de Taiwan
@evandroadrianomira6514Рік тому
Tenho uns da force aq tem mais de 10 anos q uso na oficina e ta bem file ainda mas comprei uns de outra marca tem uns 5 anos e ja tive q substituir pq gastaram muito rapido
@antaklugom7389Рік тому
I bought many FORCE sockets many years ago without knowing it is the Best and Strongest here. And I still has it now.
@alexmills1329Рік тому
I have a few cracked sockets and I now am impressed with how I managed to do it
@joew84405 місяців тому
50 years turning wrenches tell me this test means nothing. How well it grips a nut or bolt without slipping is what matters
@summerrancher804411 місяців тому
The old one appeared to be the shortest. And when you pulled fixture up on the press, it appeared to have witness marks lower on the snout like it had hit the square hole section of the socket. That would have compounded the hoop stress force and likely why it seems to explode evenly as it was loaded at the top and the bottom.
@vasantos-re4hbРік тому
Real talk - nothing you do in a garage requires 3000+ kg of force. In other works, the cheap stuff is more than enough for daily use.
@shitloveaduckРік тому
I must be some kinda strong then!! I have broken dozens of cheap sockets, big & small. When you have a 3 ft bar and are applying all the force you have on the end,,,, how much rotational force do you think you are applying? Mid level and up seems ok. The cheap stuff is generally crap. Especially when applying huge torque trying to break a nut loose.
@rustyhenry3692Рік тому
Real talk I break cheep shit all the time...
@groosbro1Рік тому
Not really. Cheaper weaker sockets will also deform under load and can round out the bolt or nut. Buy the best you can afford, but don't cheap out.
@shitloveaduckРік тому
@peter - That should be mounted on a wall as art!! Haha.
@pgmurray76Рік тому
@peter Somehow I don't think this is something the 82nd Airborne see, as they are heavily maintained powerplants.
@jaydeister9305Рік тому
"Milwaukee at 5 dollars is a great deal!"
@teropiispala2576Рік тому
It was very thick and material looked soft. Absolute strength is not the most important property. These are used by hand and should be strong enough not to break. Soft material can round out in use and if the wall is too thick, you can't fit it in many places. For my eye, bosch was probably the best. Should be strong enough, was hard material and the wall was thin. The question is, is it worth of money for all.
@geronimo6323Рік тому
@@teropiispala2576 This was only the Bosch green one for hobby use. Test the Bosch blue nut for professional use. Much better as Bosch are other german companies like Stahlwille, Hazet or Gedore. They make tools for professional use.
@SuperVexxy7 днів тому
@@geronimo6323 Milwakee for 5$ - Bosch for 17$.. so what ? And 17$ for just one Nut is of cause not a hobby tool.
@stefanpaul9443День тому
It’s the only one mounted backwards…..
@Froschus_MaximusРік тому
Bosch (electronic) tools are mainly used in the private sector, if you really value good tools you will get something else anyway. That's why I also think that Bosch is really one of the very last representative "German" tool manufacturers, especially since in the end only the brand is German.
@RAYtheram7 місяців тому
I have been using force impact sockets for a 11+ years now and they get used everyday on milwaukee impact guns of all sizes every day and they are just as good as snapon and only a fraction of the price. Shout out to trade tools in noosaville!
@petertrevorah7388Рік тому
Wouldn’t a twisting motion be a better test of relevant strength?
@gabrieljordan9977Рік тому
Yes I think the same. I don't think we will ever try to expand the socket like this
@gabrieljordan9977Рік тому
@@bountyhunter4885 Well yes but they are testing the expanding force alone. Testing it by twisting it is a real world test
@robbailey5692Рік тому
This is the press channel. Also, a tapered mandrel, such as the one used, does create hoop stress in the socket. Torsion on the socket driving a fastener head creates hoop stress as well through a camming action. They are not exactly the same but I expect that a regression model could be developed to predict the strength of the sockets using either test. But it's still cool to break $h!+. (Destructive testing).
@mattillac1980Рік тому
I break sockets with an impact wrench on a regular schedule because my boss buys cheap tools and those failures resemble these closley. The forces applied seem similar to me.
@smoke05sРік тому
@@gabrieljordan9977 But it will fail under expanding every time because this is where the thinnest wall section is and the cutting of the hex or 12 point is the physical defect where the break will occur, so it is relevant.
@Estranged180Рік тому
Every time a "tool in a hydraulic press" comes up, there's always some Milwaukee hate down here. Always. I know they're more expensive. But there's a mechanic here on youtube that says "cheap tools cost you money. Expensive ones pay you". I guess that's his way of saying "you get what you pay for."
@kyleh54983 місяці тому
Bosch surprised me with being the weakest of the impact sockets. Milwaukee isn't the strongest, but it's what I use and love their products. Thanks for the vid!
@MaxMustermann-ub9ihРік тому
I miss the Hazet and Gedore tools.
@masterimagedahРік тому
and Stahlwille
@wernerlampe8089Рік тому
Please test tools which made in Germany (Remscheid, Solingen and so on) ... ! ... And: nobody use tool's in this way and with this force! ... Sensless and rediculous. ... 👎
@dontwantaРік тому
I would've liked to see a regular flat top like the bottom instead of the pointed one, see them fail on actual down force instead of splitting them.
@afellowinnewengland6142Рік тому
So thick impact sockets are stronger than thin-walled chrome sockets?! I’m shocked! 🙄 Setting aside the fact that all the interesting tool brands are absent from this test for a moment…This isn’t really meaningful data. Increased durability through harder steel can make a socket more brittle, but still well within the range of the intended use. Also fit tolerance is important to pros. This test doesn’t have any real world benefit. As a retired tech I care about tolerances/ fit, wall thickness and durability (especially on impact sockets).
@metavto9322Рік тому
Force makes excellent sockets, no worse than snap-on
@naimvideo997 місяців тому
Thanks a lot brother. Important information.
@HydraulicPressExperiments1Рік тому
Lovely experiment ! I just did some with rubber ducks 😅😅
@Hypurr1Рік тому
Would have liked to see Snap-On and/or Mac Tools in the mix along with Harbor Freight. Milwaukee isn't the first brand that comes to mind in the US when it comes to sockets.
@ShitStefanShootsРік тому
Milwaukee isn't really american except for the distribution ...
@cmc3780Рік тому
I’ll remember this demonstration and be more careful the next time I’m using sockets for installing races with a cone shaped driver.
@thongvu4281Рік тому
Everyone who actually uses stickers regularly know that sometimes only a thin walled socket fits in some spots. I've never in my life broken a socket but I have broken some bolts.
@jcanfixall15857 місяців тому
I have broken several sockets, with a few more years experience you may break a few too...
@tornacidayi54907 місяців тому
the one with more sides, like the 12-sided one, will be stronger, as the pressure is more evenly distributed, on the other, it hits the tip, on larger surfaces on the 6-sided
@andvil01Рік тому
So a cheap impact socket from Taiwan gives you most bang for the buck. Who would have known?
@jimmydavis550Рік тому
Wow! The old impact socket had a Brinell hardness probably north of 50. Very brittle!
@mzzj2Рік тому
Note very coarse grain structure on the Old socket. Coarse-grained steel is more brittle even at the same hardness. Modern metallurgy has improved grain size and toughness by huge amount.
@limyrob1383Рік тому
Its possible it was heavily work hardened and perhaps even age hardened which could be a good reason to be careful with old impact sockets.
@wayawolf1967Рік тому
The old China crap AKA knuckle buster tools from Harbor Freight or a flea market. The newer stuff is much tougher.
@davidjacobs8558Рік тому
@@limyrob1383 I had a 30 year old Craftsman 18mm socket 12 sided for 3/8" ratchet, which I bought when I was still in Highschool. I never used it until few days ago, to remove a sway bar bushing bracket from a Mercedes. It cracked before the bolt got loose. So, I got out Craftsman 18mm long socket 6 sided for 3/8" ratchet from the same set. It cracked also. I went to Lowes to see if they are going to replace the socket for free, and they did. The new Craftsman 18mm socket I got from Lowes as a replacement did not crack, and was able to remove the bolt. The 30 year old Craftsman were made in USA, and new one is from Taiwan.
@nathanwahl9224Рік тому
And just because it was old doesn't mean that it was actually a good brand, either. Cheap old tools look just like good old tools.
@terryenyart58387 місяців тому
SnapOn, Mack, S&K, Proto are American quality tool brand names. From chrome to hardened impact sockets. I tend to feel tools made 60 years ago are way better metal than in the last 30 etc. Not sure of exact timeliness. But you can feel the weight difference for sure.
@jackreacher56676 місяців тому
Sadly I did try this out at home, I started out with a nice home, car, wife, and a hydraulic press the full deal, and then got hooked on these videos, now I live in ruins and assorted debris still with my Hydraulic press, I think I might need help with my addiction.
@KNemo19993 місяці тому
You haven't hit rock bottom yet.
@alexg49749 місяців тому
Cool video, very educational. Do you think the rankings would be the same if you did a torque test? You'd need new coupons for each test that are about ±5% dimensionally/Yield Strength, get at least 3 samples of each type of socket.
@danielcaldwell5940Рік тому
It appears to me that different metals were used. Those that resisted higher force broke in a more brittle fashion, while those that broke at lower force broke in a more ductile fashion. With the exception of the "old" one.
@The-LogicianРік тому
I was expecting the old one to do better than it did given it looked like it had thicker wall than some of the others, but suffice to say that materials engineering is better today than in yesteryear.
@nathanwahl9224Рік тому
@@The-Logician or just because it was old doesn't mean that it wasn't a cheap one at the time, either.
@robertsmelt66387 місяців тому
In the UK I bought a complete Bosch set of impact sockets for around £20. That was an eight piece set in a wallet. Definitely same as the one tested. Bosch isn't seen as a premium brand, they license the name to all kinds of products as do Blaupunkt.
@davidbrayshaw35297 місяців тому
"Made in Germany" used to be a guarantee of quality. Now, "Made in Germany" is a guarantee of expensive repairs or premature replacement. Perhaps I shouldn't be so harsh, there are still plenty of premium products that leave their shores. But there's no shortage of garbage, either. I've taken thousands of dollars worth of "German Quality" to the tip, in recent years, and I'm not happy about it.
@robertsmelt66387 місяців тому
Have you seen the trim quality in Mercedes? Supposedly leather seats are mostly plastic. Absolutely crap.
@davidbrayshaw35297 місяців тому
I've owned 3 Mercs. A '76 280 E, A '76 280 SEL and a 2004 C class Kompressor. The E and the SEL were outstanding cars. Lightyears ahead of the competition, for the day. The C class was pretty ordinary, I've got to say. Especially when it blew a head gasket! But not only that, it was a fairly poorly finished car, overall. A friend of mine, against my counsel, purchased a new C Class about 5 years ago. I never did say I told you so, but she got rid of it within six months. There was nothing good about it. Honda, Mazda and Toyota all make better cars, for less. I didn't even mention Lexus. Then there was my Miele stove top and oven, that I took to the tip, not too long ago. They started falling apart in only a few years. Screen printing on them was rubbish, the cooling fan in the oven kept failing, every control knob failed, the electronic "piezo" starters failed... rubbish. I've got Bosch power tools, too. Admittedly, they've held up well, but I'm only a home handyman, these days. It still didn't stop Bosch from selling me a battery that was faulty though. And what was the after sales service on that like, 3 month later. Another $160 Aud. down the drain. The only "nice" German things that I own now, are a dishwasher and an air rifle. @@robertsmelt6638
@lasantha.rathnayaka7 місяців тому
Wow😮 nice experiment 😊❤
@l3est_9711 місяців тому
Okay, I need a wrench from the metal used to make the drill press. 😂
@rbee9143 місяці тому
In 40 years of turning wrenches I never saw a socket break in same manner as your test...they wore out on the inside walls. Toughest tools I ever used were Hazet.
@davepg4173Рік тому
Why is the musical score at the end of the video so satisfying?😂
@joeschlotthauer8407 місяців тому
The Force sockets were impressive.
@thehouseholder54687 місяців тому
As a mechanic I don’t understand how this test proves anything as we would never exert that force from that direction 🤔
@RichardLucas7 місяців тому
Your mistake was to expect that from this channel. There are other channels that do that kind of thing. This channel is just for watching things go crack-bang-smash.
@Cedo866 місяців тому
When you tighten the screw socket tries to widen so this is not irrelevant test.
@pw692Рік тому
Taiwan is not a Chaina
@user-ci8ib6rd9sРік тому
🇹🇼This is Taiwan (The Republic of China)which is the real china 🇨🇳The is PRC ,which is another USSR today, also ChiNAZI (Red nazis)
@helikopter8390Рік тому
@@user-ci8ib6rd9s chinazi lol🤣🤣
@ameeriyyad4061Рік тому
China
@golfillozРік тому
@@ameeriyyad4061 Chaina
@joserantocb750Рік тому
Not yet.
@Biketunerfy7 місяців тому
Did anyone see the grain structure on the “old” failed socket. It looked like sugar so it hasn’t been hardened properly, I recon it probably didn’t even go through normalisation cycles to refine the grain structure. I normally trust the old tools more than modern ones because they were built to last but these days they just aren’t.
@bjs001001Рік тому
Love these videos.
@delukxyРік тому
Unfortunately the forces shown breaking these sockets are unlikely to be replicated when they are used as intended. Sockets rotate. See if you can mange to test them that way. I lent a Britool socket to a friend when he was taking the head off a Rover 2600 (SD1) and he managed to break it. Replaced free of charge but I have never managed to break one myself.
@andrecostermans7109Рік тому
Yes , sockets are meant to rotate , I wonders why testing them this way ? There is also difference in metalcomposition between impact sockets and regular ones , each should be tested in their own range .
@obiitom11 місяців тому
my guess is it has, although not fully accurate, some correlation to the amount of outward pressure the socket can take before splitting, a particularly tight nut/bolt made of a really tough material could remain stationary while the socket turns as the socket stretches round the nut/bolt. i've split a few of sockets in my time, some through abuse (chromes on an impact wrench) others when used correctly, it's rare though as usually the nut/bolt just rounds off.
@lyelljaeschke818010 місяців тому
Most bolt heads on the engine and body parts in my 80series Land Cruiser have tapered heads so using 12 sided sockets is not a good idea. With these type of bolt heads the main contact area is right at the tip of the socket hence a lot stress in a small area of a socket
@jamesjackson42244 місяці тому
@@andrecostermans7109I think he's just amazed with tearing shit up with a hydraulic press.
@maxsteiner8268Рік тому
The Force runs strong with that winning socket.
@shadowtrooper4435Рік тому
Dude...Germany's ripping us off.
@nigelmiller500Рік тому
@@shadowtrooper4435 Yea a lot of Bosch's power tools used to have a good rep and then they started making them in China so I stopped buying them .
@maximumeffort4043Рік тому
My car mechanic heart is screaming, great video though
@RustyInventions-wz6ir4 місяці тому
Just found your channel and Subscribed. Very nice video
@dokterkarel11 місяців тому
"do not try this at home". Thanks for the warning, because we all have 100ton presses at home.
@mb1064297 місяців тому
You need a 100 ton press to try to crush a socket
@robinharwood50447 місяців тому
I just bought one precisely to try this.
@dokterkarel7 місяців тому
@@robinharwood5044 dedication!
@rogerioroda4266Рік тому
na minha opinião a q rachou no meio com 4 toneladas é a melhor de todas material duro não tem desgaste em uma oficinha q usa diariamente as outas pode aguentar até 70 toneladas mas é macia sem durabilidade a que rachou com menos peso é a melhor de todas obebençendo o torque é uma ferramenta q passa de pai para filhos e netos e bisnetos as outras não
@lt1980Рік тому
hasta no ver no creer
@RobertooliversРік тому
Tem isso!!!!
@antesdedormirmanu6789Рік тому
Those force tools are awesome professional grade tools...
@Sebastian-lk7rq7 місяців тому
The socket wrenches aren't virgins anymore. It hurts, that's why we done it right.:-)
@AmeisenigelytkРік тому
0:01 Guess I won't repeat this with my hydraulic press at home
@iceymonster4675Рік тому
Genuinely I think that every video lol. Was going to post the same thing xD
@QueenieTheDogРік тому
You have a hydraulic press??!?!?!1!
@dougaltolan3017Рік тому
@@QueenieTheDog you don't???!
@pgmurray76Рік тому
@@QueenieTheDog They are equating a Harbor Freight Pittsburgh shop press with hydraulic jack cylinder with this medium sized dedicated hydraulic pump press. I have a Pittsburg '12 Ton' . Nice and square with bolts and welds.
@ningbojiejietoolsco.ltd.1766Рік тому
Material and thickneed are important for strength
@travetart6964Рік тому
تحية حب و تقدير من المغرب إلى دولة تايوان الأبية
@finncarlbomholtsrensen11883 місяці тому
For being able to work on my seat rails in my 1970 BMW (Changing the seat to a decent version, not that flat and able to be angled) I had to buy a very expensive ARAG socket head, compared to my old HERO, which was too solid made. The last functioned fine besides in this case.
@bobdylan7120Рік тому
So, according to your test parameters and results - the best wrench sockets would be those made from rubber, which would continuously deform and not fracture!
@obiitom11 місяців тому
the reading goes down as soon as the socket deforms before the split, it wouldn't even read if the socket was rubber.
@beauboydaveРік тому
The test doesn’t really mean a great deal, this situation would never be encountered anyway. It’s torsional strength they want to be testing. still, enjoyed it anyway.👍
@deborahcuster814211 місяців тому
those things cost way more than $5 per socket. the best one made , is the old socket . it did not give as like the others did. now that wa a very good socket. impressive video. thank you .
@michaellong2661Рік тому
Some of your videos are purely amusing with no practical application. This, however, this is useful knowledge.
@bobbliss5175Рік тому
I think the point here is that most of these are pretty safe, what would you be doing for those sockets to be breaking?
@MarceloLopez-by5kgРік тому
Taiwan 💪🏻 me sorprendió
@user-mq5ym7ko3g8 місяців тому
Steel is the one who explodes. The winner is the old piece
@jacktattis5 місяців тому
I have Stahlwille bought in 1975 Absolutely great Used it of Track Bolts, Centurion Track bolts could not fault it
@m.b.82Рік тому
Taiwanese for the win
@luisaaraque3332Рік тому
Sería genial si colocarás una tabla al final de la prueba para sintetizar el conocimiento aportado por el experimento...
@antoniogzh9724Рік тому
El force de impacto es el ganador con más de 12.000
@antoniogzh9724Рік тому
Q sorpresa pence q el Milwaukee iba a ser mejor
@anthonywest1974Рік тому
Nice but don't forget Gedore in your tests. 👍
@JohnJones-ce5riРік тому
The old socket bowed out early but geez it put on the best show.
@ONLY_RESPECT-6832.Рік тому
Force tiawan impact 3 dollar is great
@antonios16vРік тому
About Bosch socket , the real price is 42 euro the set. Included 9 size in set.
@Burnman83Рік тому
True. Also Bosch is not really known to be a high-quality producer of mechanical tools, and afaik none of them is manufatured in Germany, but in China. For tools actually coming from quality brands and manufactured in Germany that actual mechanics or professional garages etc. would use, please refer to "Stahlwille", Hazet or comparable brands for a better comparison. You can also include Wera if you want a high-quality Czech brand in the mix as well.
@angelamyraРік тому
Another really good brand of tool is Beta from Italy, i still use these every other day and they are over 40 years old.
@manuelpinto48092 дні тому
Now Beta its no more Beta. The quality is low compare witht your 40 years tool.
@noahmizrahi9834Рік тому
The last one, the one called "old" snapped rite in half. You can super glue that one back together it was a clean break
@pepelopez7518Рік тому
La forma como el cono de la prensa ejerce la presión y extensión sobre el dado no es la misma que recibe durante el uso normal . No se qué tan significativos sean los valores obtenidos.
@GuilhermeSchmidtdaCostaРік тому
Durante o uso, a performance de resistência vai ser muito parecida. É perfeitamente válida a forma como foi atestado
@imamsyafii5346Рік тому
Buatan Taiwan bagus👍👍👍
@swantykoswara50357 місяців тому
Yang buat kontennya engga bener Klu yg warna putih bukan baja cuma dilapis Croum Sedeng kan yang warna hitam baja yang dihardened
@swantykoswara50357 місяців тому
Coba kalau yang dites nya terbalik Buatan Jerman + USA pake yang warna putih , sedengkan China + Taiwan pake yang warna hitam Hasilnya akan terbalik
@albertapeetМісяць тому
To me. Sockets are engineered to withstand twisting force. Ramming a cone down the center means very little . But I watched anyway so , mission accomplished.
@BeerBaron-hx4evРік тому
In the beginning of the video, I think either your camera lens needed cleaned or there is a plastic film over the lens. Still pretty cool how they hold up.
@indrajeetroy6464Рік тому
I could easily predict which side of the socket is going to break by looking at the offset placement.
@Flips420Рік тому
Youre neat
@dominadoralegado1121Рік тому
Taiwan winner?
@dominadoralegado1121Рік тому
@crazyhydraulic205 how?
@MrKociuРік тому
About testing the old fields tools how many times being use it you cannot compare to the new one
@BASE_Automotive7 місяців тому
A CHART AT THE END WOULD BE GREAT!
@t596978Рік тому
Taiwan is taiwan (ROC),china is china(PRC)
@assoumalola7351Рік тому
😂
@auliaadri7998Рік тому
Taiwan is also China
@TiegerlemonРік тому
@@assoumalola7351 taiwan is China
@lennyray42Рік тому
China is also Taiwan
@rubensoares1099Рік тому
China is coc
@DailyDoseOfTopCommentРік тому
So i thought Taiwan was dominating only the chipset industry.. now they even taking the socket industry too
@dougaltolan3017Рік тому
So so many people won't get that. 👍😜
@leeshackelford7517Рік тому
Taiwan has been making high quality items for decades. Yes, they still make budget items. Some Taiwanese will buy high quality items that will last DECADES, while others will buy lower quality and just replace things in few years. I prefer quality. My bookcases and furniture are 25+ years old and no warping. (Good solid teak and oak....entirely...no thin fake stuff on back side) I prefer my Cannondale with Campy parts bicycle....but Giant has been making top quality bicycles for decades....high enough for use in races like Tour de France.
@tonoalvarado14367 місяців тому
¡Qué videos más satisfactorio! Me hubiese gustado que probaras solo con cubos normales y otro solo con cubos de impacto. Saludos desde Honduras.
@Brown_Buffalo7 місяців тому
They would make some nice rosettes for an abstract flower sculpture
@hectorzamora2095Рік тому
Now you know. All the crappy old sockets that you been saying are better, I guess not. Is just a myth 😂😂 Taiwan for the lol 😆
@user-ci8ib6rd9sРік тому
Could you please calculate the '' Pressure (kg)÷ Price($)=value(kg/$)'' ,as a reference plz ?😁😁 I would be really appreciate.😃😃 Thus l could see whether it is worthy to spend my money💵💰, and check how exactly every dollar could bear how much press.
@user-ue9sz5rj9wРік тому
👍🏻🤣
@tothcsaba28697 місяців тому
If the socket stretches, it is bad because it also distorts the screw head. Therefore, it is better if the socket breaks in the highest possible Nm range.
@user-bx9el8gv1dРік тому
인터넷에 이런 거 올리는 거면 진짜 대단해요
@mohammadhoseinkhatami9703Рік тому
Please note the results at the end🙏
@pengshengyung9721Рік тому
taiwan great
@kenmontgomery2187Місяць тому
I want you to compare these German brands. Idk what they do to them but they are THE toughest sockets wrenches “hand tools” I’ve ever used. Most don’t have never heard of them. But servicing large manufacturing machinery for 35yrs you won’t find a stronger socket… guaranteed!… first off is Stahlwillie brand very expensive but very reliable & highest quality possible. Using a torque multiplier loosening M24 bolts that require over 2000nm of force during assembly, was exceeding 2500nm when trying to break them free after 15yrs, With a 1” drive adapted down to 1/2” drive after breaking ever 1”, & 3/4” 32mm 6pt socket in North America (from memory probably 6 or 7) Stahlwillie not only made a socket, but took them all out & is still in service today! Those broken sockets were not cheap harbor freight shit, they were Snap On, Proto, Westward, & yes Crasftman… a few others I would guess to be as strong, are Wera, DeGeorge, Wima, & I know Theres 1 more I can’t think of that’s very popular. Id love to see tests that consists of strength by top manufacturers of industry leading Countries…. Im ashamed to say it, but I will…. I would bet USA, would barely out do China, or Taiwan! & I’m not sure of what other lesser known high quality tools are out there but they’d have a hell of a title to beat any of the manufacturers I listed above
@keanvanderwesthuizen34766 місяців тому
The Taiwan tools thats very impressive good work Taiwan i own some tools made from there bluepoint owned them over 10 years great stuff 👍😊
@ianf5748Рік тому
Taiwan No.1
@praveens3774Рік тому
It's made in Taiwan, not China. Taiwan is a separate country not a part of China. If its made in China then the socket would have broken before it reaches 1000 kg lol..
@MrRunner3 місяці тому
The old adage, you get what you pay for is so true. I have a huge number of tools and most are UK, German or American, which I have had for 50 years +. As I age and do less, I buy Chinese stuff, I's not worth me spending a lot of money on tools that I no longer use to earn a living. Very useful video, ty
@carboncarbonx437 місяців тому
Confucius say: Man who run through airport turnstile sideways going to Bangkok.