#automotive #lathe unscrew the broken bolt without drilling and welding, simple trick unscrew the broken bolt
КОМЕНТАРІ: 3 100
@basspigРік тому
I've never encountered a broken bolt stud that could be unscrewed that easily. Usually the studs break because they are stuck so tight that the force required to loosen them is greater than the strength of the bolt.
@dragonnorwayРік тому
I think this bolt clearly snapped under use, and not while trying to disassemble it, if it was corroded stuck, this method wouldnt work. Unless he heated it up and broke the bond, and got enough corrosion solvent in there over time then this could work, but then it would be easier to just weld the bolt, as that adds both heat, and a way to turn the bolt again..
@larrynorsworthy8582Рік тому
Probably from stud stretch. Then snap
@zoltanliszkai2162Рік тому
Or galled
@endurofan9854Рік тому
and one more thing, he used tap and blow pressured air on scrapped aluminum, not a good way of doing it in that situation, those scaps might have entered the engine even with the cloth there
@franciscofurlan4001Рік тому
This is almost impossible
@aleksbugz2425Рік тому
Стакими ногтями его можно было просто ногтем выковырять)))
@alexandrbaytimirov5498Рік тому
😄
@huntfishgeographic9618Рік тому
Это пиздец, там компостная куча под ногтями, отвратительно, несмог смотреть
@odinochka42Рік тому
Америку явно не открыл. Я в детстве так делал.
@user-un8bu4xw7tРік тому
Алекс нельзя, а вдруг резьбу испортишь.
@user-dv9wl3cd4tРік тому
Эт точно
@user-gk4ix3bl4rРік тому
Когтями этого мастера можно выкрутить любой болт 🐾🤙🏻🔥
@user-cr3ux4yc7qРік тому
По деревьям можно лазить!!!!
@user-gd5li6su5cРік тому
И нельзя совать в вагину !
@user-tl5gr5il5fРік тому
Росоямаха
@user-tu5vl6wv9wРік тому
@@user-cr3ux4yc7q древолаз😁
@user-travelleРік тому
Баба вроде это
@user-mg9gw4ir2m5 місяців тому
Те,кто сталкивался с подобной проблемой,знают,что этот простой трюк работает крайне редко .
@vladimirkulikov3598Рік тому
Показан очень сложный случай - обломок свободно люфтит. Вот, если, обломок чуть прихватило коррозией, или на герметике - тогда, вообще, раз плюнуть!)))
@romankapustinKaРік тому
Он сам его наверно закрутил обломок и героически извлек
@sergeybondarenko4733Рік тому
@@romankapustinKa похоже он ради пиара выебнулся, ну бля не $ука он?
@romankapustinKaРік тому
@@sergeybondarenko4733 да ещё какая
@user-xo3zy4iv6dРік тому
Как вообще умудрились сломать свободно болтающийся в резьбе болт? 😂😂😂😂 Научите меня!
@air2674Рік тому
Это видео про маникюр)
@MikePr1791Рік тому
Болтающийся остаток болта можно было выкрутить выверткой левой и не долбить полчаса. А с такими когтями можно было прям ими как отвёрткой крутить 😂
@user-iu8ir7hi9vРік тому
При нарезании резъбы в алюминии или их сплавах используют обыкновенное мыло ,а не масло как по стали.Проверено....
@user-hl7mm5qf8nРік тому
Когтями😁😁😂😆🤣
@user-tt6mg6kp1lРік тому
Идиотизм
@RukowРік тому
Когти иногда надо стричь, верно. Или у них там это не по баблу? Неприятно.
@aleksandrdobrinin4714Рік тому
🤣🤣🤣👍👍👍 до слёз...
@A1ex5438Рік тому
Сверление и сварка уже выглядят проще и доступнее, чем способы на видео.
@vladredline2767Рік тому
кувалда и болгарка, плять!
@vadimaleksandrovich5842Рік тому
@@brothershooryn_219 вот именно, как хрен в рукомойнике
@Mondeo2175 місяців тому
Слишком глубоко болт обломался, сваркой не дотянуться.
@philippeallaire60364 години тому
Percage et extracteur avec un pas a gauche👍
@paulkurilecz42097 місяців тому
I generally go with the concept that if it is liquid it cannot be stuck. 🙂 Seriously, anybody who is working with steel bolts in aluminum castings should be applying an anti seize when assembling the parts. It will also help to prevent stripout when tightening the bolts.
@-Jahan-Рік тому
Это просто фантастика. Жалко что такие заломыши встречаются в одном случае из ста из за того что это был говноболт. Обычно это прикипевшие, приржавевшие или обломанные из за того что не по резьбе закручивались и вот там всë это не работает. А вот удаление такого заломыша как в видео я бы и снимать постеснялся.
@user-sb4vf2sf4jРік тому
Первый обломок испарился после прохода метчика а второй это вообще смех ,в жизни такое бывает один раз из 100.
@user-vj2mc8dg7bРік тому
Вы правы, дать бы ему выхлопной коллектор со сломанной шпилькой, как бы он её выкрутил.
@user-sb4vf2sf4jРік тому
@@user-vj2mc8dg7b метчиком прогналбы ))
@user-gh7rg8wp6eРік тому
Счастливая бредятина .
@-Jahan-Рік тому
@@user-gh7rg8wp6e ну верить или нет это твоë личное дело. Так и живи считая что в России все в говне живут, тогда глядишь своë говно меньше вонять будет. Удачи тебе, дружище.
@bigwo56Рік тому
I normally use a center punch to: A. Shock the broken bolt, THEN: B. use a left hand drill bit and SLOWLY drill at the center punch mark INTO the broken bolt. MOST of the time, the bit will bind into the broken part and back it out for you. If not, then you can use an extractor in the hole made by left hand drill!. TIP: A bit of grease will catch the shavings and keep them out of the engine.
@billythekid9694Рік тому
That is the best and surest way to have the job done.
@sandgrownun66Рік тому
Bolts usually break because they're seized in. This bolt came out much too easily. The thread was even loose. This isn't going to be the case, most of the time.
@johnsolenski140Рік тому
Agree best fix for the bolt shown in video. I would add to leave the drill bit loosely chucked as to not break the drill off in the broken bolt.
@sandgrownun66Рік тому
@@johnsolenski140 The bolt in the video didn't even need a drill. All it required was a punch to extract it. Hardly much of a challenge. The first half of the video about fitting a helicoil, wasn't even mentioned in the video title.
@Andrew_KosРік тому
Повесил тряпку, чтобы стружка не попала, а потом сжатым воздухом продул... Зачем тряпку клал?..
@general510411 місяців тому
Application of HELICOIL and punch-walking are two old-school crafts that were taught back in the early part of the industrial revolution. Schools used to teach these principles but technology has all but buried these common since crafts. My dad raised me in a machine shop, so He taught me these principles. I learned about HELICOIL application at my railroad career, and it's SO GOOD to watch it demonstrated on a free-to-watch video to the world! THANK YOU for your video !!!
@RobisteРік тому
Если заломыш не прикипел и так свободно болтается, он бы не сломался. Ролик - "сказка"
@user-or1fb4lf7j3 місяці тому
Китайские болты ломает при стягивании . их просто отрывает. Эта процедура работает. Конечно лучше просверлить левым сверлом небольшое отверстие и забить в него шестигранник
@user-yv3hn6dy5e3 місяці тому
Всё ещё проще в плане шестигранника. Можно выкрутить экстрактором.😉👍@@user-or1fb4lf7j
@denis94507 місяців тому
In my forty plus years as a service engineer I would say I have removed maybe 50% of bolts like that but normally they are to tight to knock around, if you have a bolt that is snapped a good way down the hole a good trick is if you have a Lathe get a socket cap screw the same size and thread as the snapped one put it in the Lathe and drill a hole through the centre then put it in the hole were the snapped bolt is then using the same drill bit drill through the snapped bolt it allows you to get the dead centre you can then put penetrating oil down the hole and use an easy out. I always keep a selection of different size bolts ready to use works a treat.
@toma51533 місяці тому
Great tip, thanks!
@_-JohnDoe-_7 місяців тому
This solution is effective only in one case: when the bolt breaks off while being tightened, and when it does not rest against the bottom, after which, usually, the thread “unwinds” and changes pitch if the tightening was carried out without observing the torque. therefore, you first need to make sure that the thread has not “unraveled” on the broken edge. otherwise, when turned out, not only the pitch, but also the alignment will be destroyed on the upper remainder of the thread.
@chetr2171Рік тому
Loved how he covered the chain with the rag and then blew everything in deeper with the air
@jeffharper7579Рік тому
He covered the chain so it couldn't LINK up with other parts and laugh at him if he messes up, that might start a CHAIN reaction😆. Yeah I don't know why you would only cover something then blow metal fragments all over.😵
@Babas1973Рік тому
Ногти подстриги!
@loubakker5000Рік тому
@@jeffharper7579 Thought the same. Made me smile.
@janscorpio2323Рік тому
@@loubakker5000 già... i frammenti di metallo vanno sempre in giù... 😂 😂
@johnnybraceРік тому
suction please nurse
@laurieparker1414Рік тому
He could have used his finger nails instead of the 2nd hand ground down pliers.
@kkuenzel56Рік тому
🤣
@sheeznutz2254Рік тому
I clicked to comment the same exact thing! Lmao
@nomayor1Рік тому
He could have also used a vacuum cleaner instead of blowing with air the metal shavings into the engine!!
@vallam3531Рік тому
Could be a woman, fingers way too long as well.
@johnholmes5674Рік тому
I’d say a drill and Easyout would still have been quicker with less chance of damaging the upper threads with that homemade centre punch
@user-ds5js5bz6iРік тому
Господи я на одном дыхании смотрел эту очень сложную операцию по извлечению сломанного болтика. Хотя мне показалось когда он дул воздухом тот болтик сам уже начал выкручиваться. Одним словом мастер своего дела
@user-du8xc6wu4fРік тому
Маникюр ШИКАРНЫЙ... Где такой делал? Неужто там же, в том же салоне? Я на болтик даже и не смотрел. Да он от чертилки и так бы выкрутился... :)
@user-sd7uo3vx1h7 місяців тому
Ребята,ну видно же ,что это чудо мастера из Индии😅
@jeremyhicks6889Рік тому
Great trick that almost never works. Only when the screw is completely free of contamination and corrosion and is not deformed at all. A little galvanic corrosion or rust or oil sludge and it doesn't work. If the bolt is cross threaded it doesn't work. If it is bent it doesn't work. If it breaks in tension, the top few threads are usually deformed and it doesn't work. If the screw is stainless it doesn't work. If a steel screw is threaded into aluminum, it doesn't work. I could go on. If you have actually tried this trick, then you have probably resorted to drilling and using an ez-out or welding a stud, or drilling and re-threading to a larger size, or drilling and heli-coiling, which is what you see him doing on the first of the two holes. Probably because the simple trick didn't work and he resorted to using a drill and drill guide to remove the bulk of the bolt, then a dental pick to try to pick out the remaining pieces, then ran a tap into the hole, found out that the thread was shot anyway, then bored it over, tapped it, and put a heli-coil it. Note that you can see the stub of the broken screw in the first hole before he starts tapping, then there is a cut at 1:47, and turns the tap back out and the screw piece is gone. These UKposts tricks and "Next level process" videos always make anyone who has actually worked in a machine shop or repair shop roll their eyes back in their head. When you see "life hack." "next level," or "simple trick" in a youtube video, it should set off your bullsh!t detector.
@lorenzotrevisani4421Рік тому
These people are only aprendists, not qualyfyed techition.
@savage22bolt32Рік тому
I have used the hammer & punch or chisel method many times. I was born before easy-outs were invented & I couldn't afford a welder. What I have is patience and tenacity.
@andygilbert1877Рік тому
@@savage22bolt32 Yeah, I’d agree. This is all you need a lot of the time, and is the most basic method so you need to learn it first! On teaching it to apprentices I’ve often heard “ah, would never have thought of that!”
@billythekid9694Рік тому
RIGHT ! Jeremy Hicks is 100% right. When the trouble is a broken screw...OK, sometimes it works, provided you got enough room for the maneuver. If the hole is too deep it won't be possible. In that case you must use a carbide drill and make a hole right in the broken screw. But when you got a broken tap...which usually is stuck, matters become more complicated. You get the job done if you have a tap extractor. Not a cheap chinese stuff as it will brake easily. The Walton stuff may be the right option.
@tinof5829Рік тому
You took the words out of my mouth!
@jeremysaunders9916Рік тому
Came here to learn something, what I learned is how to contain swarf within the engine using a rag and a airline 😵💫 top mechanic !
@phillipwatson444110 місяців тому
To install a helicoil you have to first oversize the hole , thread and then put in helicoil. for the second bolt only one in a thousand will come out this way. A left hand drill bit will remove some and in the other case a small drill and an easyout will remove the bolt. If not drill out the hole with a slightly larger bit and either tap to larger size or tap and install helicoil.
Парень с длинными ногтями - ты лучший! Такой херни я давно не видел. Ключём ты болт обломал, а кёрнышком так спокойненько, не напрягаясь - тук, тук - и открутил! Молодец!
@molibdenum4210 місяців тому
КлючОм
@user-bt9xf1ew7h10 місяців тому
Этот парниша не русский - у них мозги через жёпу работать....
@Mondeo2175 місяців тому
Этот парень факир, у него всё получится!
@olegzlatoustovskyРік тому
Тряпочка конечно выполнила свою задачу😂
@kasak1977Рік тому
Это точно
@6363OKРік тому
это чтоб не отсвечивало
@bonifacypiechowiak9277Рік тому
@@businesstrip1086 tylko przeciw potu
@user-s_a_gРік тому
Первый раз вижу автослесаря с таким маникюром 🤪
@vitaliytabskov8450Рік тому
Выключил после первого момента с ногтями!!!!
@air2674Рік тому
Это чтоб в носу ковыряться)
@user-ev4iv6eo2kРік тому
Европа однако.....
@user-rk3yi4on4pРік тому
Он солидол под ногтями домой вороует
@botapetkov1329Рік тому
Хули за смену лак стирается,он после работы подкрашивает.😂
@elrobo356821 годину тому
What good does it do to cover the top of the tapped when the cuttings are are falling down into the engine? oh, I see the air will blow everything further in.
@caspernext1939Рік тому
Проще простого, попробуйте таким способом извлечь прикипевший остаток болта или закрученный не по резьбе)А тут можно было и когтями)))
@fate-noРік тому
Здесь смысл не в извлечении "заломыша", а в заголовке ролика. Эффективная замануха - наше ВСЁ!!!
@williamgilchrist8577Рік тому
Hello, Thank you for the video. It was very informative concerning one method of removing a broken bolt and in this case in an aluminum casting. Using a punch to screw a set of threads on out the way they were going. I used to be a machinist in a Ford road truck dealership and removing broken bolts was part of my purpose and I did remove hundreds of them. I just want to bring up a couple of points. Point 1: It is seldom you get a broken bolt that will come out like you have just shown in this video. Most of the time, the reason the bolts are broken is because the threads are stuck in the threads the bolt is put into. Removing any broken bolt, I used to always try to use the method you have demonstrated first as it is the easiest. When I have tried what you have shown and the threads are stuck where they will not screw out, I try taping strait down on the broken bolt to see if that will break the threads free. If not, I will put some heat on the broken bolt and going forward, there are more invasive ways to do that will come next. Point 2: In the video, you attempted to surround the place where you were working with a cloth to keep from getting savings down in the head which will ultimately get into the crank case. You did good putting the rag around where you were working. But, the next thing you did was take an air line to clear the trips away where you could see. Well when you used the forced air, you just blew all those shavings and chips right up under the rag. Not Good.
@JCcanUРік тому
a 50 cc engine not the same as a 350 F150 eh get a drill and left turn cutting edge be done . as for tapping I use duct tape and a good rag . keep the chips out . seen the same thing there goes the crank bearings lol
@KartraceoneРік тому
Exactly what you said, my experience is the same as you described, and also to keep shawings under control I use grese besides rag precut shape to fit snugly around the place which needs attention. This is pretty much untipical. Also lefthand drill bit is of great help.
@endurofan9854Рік тому
exactly, the rags purpose was useless when he used the forced air
@nicolaesuciu937Рік тому
Eu, inainte de a posta o filmare de acest gen, în primul rând cred că mi-aș tăia unghiile 😀
@felixmotanul524210 місяців тому
Man, stop trying to convince him. In India anything is possible. It's full of UKposts with such engineers
@accelerateddragonРік тому
This is no secret, most seasoned mechanics that I've ever known will always try to remove them with a pick before drilling or welding. I've also sacrificed small screw drivers or flat bladed chisels, grind them to fit the hole and make a screwdriver slot, some time the use of a hand held impact to get them started. Not always successful, but always worth a try.
@raybame5816Рік тому
You are right to try this first, call it plan A. When this fails, go to plan B which is drilling and EZ outing. Plan C is welding a stub on and/or apply heat.
@user-ds6qf2mv1qРік тому
Походу шпильку обломали на закручивании и с упором носика в тело головки, не в край резьбы, иначе обломок так легко бы не выкрутился
@hagakure1999Рік тому
Не это не так было, скорей всего крышку снял, спецом туда обломышь с руки ввернул, а потом выебывается, вот типа, смотрите как надо было))
@cdabg10 місяців тому
I'm assuming the bolt broke when tightening because no corrosion is present. Nice presentation on Heli-coil prep and installation. This person is well-experienced on proper tapping procedures of aluminum, backing to break chips and clearing chips before they score the new threads. Nice video!
@chrissmith21145 місяців тому
He is just letting all the swarf fall into the engine.
@herbertvanrensburg64117 днів тому
My good friend, I can assure you that if that bolt had heat seized in that casing, no amount of tapping it with a punch would get it to loosen up. I also love the way you use your circlip plyers to remove the bolt, what happened to your long nosed plyers?
@user-lo9vf5rt2uРік тому
Вся стружка в движке. Молодец косяк.
@user-xr2ze6gv1wРік тому
Ещё и песок от грязной тряпки, которую он закинул на двиг якобы от стружки.
@noerodriguez1252Рік тому
Thanks for the tip. I'm no longer a mechanic and I used to do the same for hummv cylinder heads. But it doesn't work most of the time. I would use left handed drill bits too.
@robertwinsper7409Рік тому
I've used the same trick myself. I used a masonry nail as a punch with it being very thin, sharp and very hard. Take your time and care don't mash the hole or the end of the broken off bolt up.
@donwest53879 місяців тому
normally installing a heli-coil requires drilling the housing over-size.!?
@user-qf2qf2mu2t10 місяців тому
Когда он начал выкручивать обломок круглогубцами, я подумал это оператор ему решил помочь своей рукой😂
@user-vu9gi8ym6b7 місяців тому
))))))))))))))))
@Igor-uo6tcРік тому
Вот это по нашему. Закрыть (местами) тряпочкой и ...Раздуть( а не пропылесосить) всю стружку по всей "башке" (гбц). Лайк за солидарность в технологиях "срача". (Шутка , хотя...)
@odinochka42Рік тому
Бро да мы Русские это поняли)))
@Igor-uo6tcРік тому
@@odinochka42 Нам бы славянам немецкой чистоты и точности .... Смотря этот ролик, сам себя поймал на мысли что и я, такой же" чисто плотный" моторист.Ведь сам уже в дв.ЕР -6 (BMW) ронял сухари клапанов в канал цепи привода ГРМ . Потом сутки искал, пока не нашел .
@odinochka42Рік тому
@@Igor-uo6tc я это проходил тоже. И теперь все отверстия закрываю тряпочками)))
@Igor-uo6tcРік тому
@@odinochka42 На эту тему есть Байка. При встрече в Тегеране Сталин задал вопрос Черчиллю : "Что Вы думаете о Русских воинах? " Ответ Черчилля был : Вы ,русские - единственная НАЦИЯ ,которая упорно создаёт себе проблемы и... с не меньшим упорством их решает."
@user-do7bu9gr3wРік тому
@@odinochka42 надо просто метчик густо намазать литолом. Тогда вся стружка выйдет с метчиком обратно. Обтер и стерильно.
@nenev88Рік тому
Этот мастер-фломастер когти стрежет когда-нибудь?
@fastcrossРік тому
what horrible nails ...
@user-it6vt6ny3cРік тому
Да не когда, зачем? Они сами обламываются 😂😂😂😂😂😂
@sergeybondarenko4733Рік тому
Он этим когтем в нутро своей пУ́сечки 😂 прощупывает каждый раз
@andrewdronsson90287 місяців тому
Они у него самозатачивающиеся.
@PiefacePete4610 місяців тому
Many years ago I had a stud break just below the surface of an alloy engine block. The guy who saved my bacon took a short length of mild steel flat bar, drilled a hole near one end, slightly smaller than the stud diameter. He then TIG welded the bar to the broken stud through the hole. He then just unscrewed it, the heat of the weld also helped free up the corrosion which caused the breakage in the first place. My broke stud was held completely tight... the method shown here would never have worked.
@kathyhathaway88237 місяців тому
I see this video was just over eight minutes long. Good job tho . But if you have never tried left hand drill bits you will be greatly surprised by trying them. This would have took less time to do than it took to put the bit in the drill . But you did great your way also . Thanks
@thrapsedРік тому
Simplest way is not to break the bolt in the first place. If it feels tight, apply a little heat to the bolt head only. Cool with air line and repeat as many times as necessary. It usually works after the first couple of applications.
@stijnvandamme76Рік тому
cool, but you tell that to a bolt that just snaps from having been torqued up and heat cycled and just lost the will to live while installed
@thrapsedРік тому
@@stijnvandamme76 Yep, I'm afraid some will just break anyway, Just tough luck sometimes
@savage22bolt32Рік тому
I have done this before too! Thanks for the great video, and a huge thanks for not ruining it with crappy background music.
@djemdjem1869Рік тому
Способ конечно не очень,но ноготь вообще огонь 🔥🔥🔥
@user-wn5gp2dr2jРік тому
Развеселил! Молодчина! Кометы, огонь!!!
@samsunggpsserviceРік тому
Как же он этот болт обломал, если он так легко идёт? А главный секрет, как выкрутить болт - это ногти не стричь. Никогда. 😳
@chechey626Рік тому
🤣🤣🤣🤣🤣
@hagakure1999Рік тому
Сам наверно его туда и зах@ярил))
@user-gb2bt5xj8pРік тому
Обломаный болт прочно сидит в гнезде, пальчиком не достаёшь.
@andrewdronsson90287 місяців тому
Это такие специальные Когти Самозатачивающиеся.
@hanyhashem60403 місяці тому
You are creativity It's true I am a new subscriber to your channel and this is my first comment in this video that deserves all the appreciation I wish you success and lasting success, God willing and his blessings Your friend Hani from Egypt from Cairo
@MikeSmith-nu9wtМісяць тому
I wanta see how ya'll lifted them blocks and built those pyramids ? If its a secret i won't tell no one ? 😂
@olenaerhardt77254 місяці тому
@ 4:43 May I know the name of that conical tool? Thank you for the great film of a very skilled master.
@EvgeniyFadeevРік тому
Мне больше всего понравилось выкручивание болта пальцем! Ну и, конечно, надо было в двигло ещё пару щепоток стружки и какого-нибудь мусора насыпать. Для надёжности!
@user-dr9rg9hc3uРік тому
Прикрыть старыми штанами, вот это поворот.
@landog59Рік тому
Nice job all the shavings inside the valves 👍
@Pazair-nq6glРік тому
Bueno, siempre puedes soplar; pero espera!, aprovecha para antes pintarle las uñas 😉
@user-kz6vo8jc1qРік тому
А что за машина ЗИЛ 120 наверное такого мастера как он будет этот беркут
@user-xl9py6nq9v7 місяців тому
А из чугунного блока прикипевший болт так получится выкрутить?
@rumynKSF3 місяці тому
да ты просто чертов гений!!!как я жил до этого ,засверливая обломок и пользуясь левым метчиком,чтобы его выкрутить?все -зря...но теперь то я знаю,как надо и легко выверну все обломки,не напрягаясь со сверлением..почему я не знал этого раньше?
@KfzogРік тому
Обычно прикипевшие или ржавые болты ломаются,посмотрел бы я как он их выкрутил этим сомнительным способом.
@romarioshpalov8463Рік тому
Да ты ещё не видел как он по пальмам лазит с такими когтями🤣🤣🤣
@DimaDima-jo7zdРік тому
По щючьему велению....
@michaeldvorak555610 місяців тому
You could use a drill bit that runs counterclockwise to drill a center hole in the broken bolt. If the bolt is loose enought the drill would back out the bolt.
@ErmolayNefРік тому
Это не проще, чем засверлить сломанный болт обратной резьбой или парой отверстий для ключа по типу вилки.
@ngreen3151Рік тому
I encountered this very same thing on my 1979 morini 350 when a hardened trunion (rocker shaft) stud snapped flush with the head. My dad who was a marine engineer taught me this exact same method using a small sharpened punch and it worked!!
@quay007Рік тому
The best way is to take out the whole piece and drill the broken bits with smaller drill bit on a perfectly horizontal surface. The way it is done here, there may be problems later when fasterning back the machine as the screw trade has been damaged. The method show here not in line with precision engineering.
@marcelomoosРік тому
Its that a 4 stroke engien insite a plastic case ?
@michaelharvey164010 місяців тому
I have had numerous old cars with rusty water pump bolts that like to break off and those reverse cutting drill bit will usually get them out especially if they arent stuck to bad and then I use stainless bolts when I assemble and use anti siege compound and they always do good
@michaelharvey164010 місяців тому
It helps to have several plans of attack I usually have about three ...
@alanblackford2962Рік тому
Nice to see he blew the swarf all around the valves and rockers, should have taken more precautions.
@roberttwist5190Рік тому
Must not have had a vacuum!!
@robertocarneirogalacio8967Рік тому
Um parafuso quebra por excesso de força no aperto. Este está completamente solto. Quando quebra e trava, o melhor ( se possível) é furar o centro com uma broca fina, ir alargando o furo com outras brocas e por fim usar um macho de rosca esquerda.
@user-th8eu7uc3h3 місяці тому
Если этот обрубок изначально болтается в резьбе, может его туда для съёмок закрутили?
@ArtN20444 місяці тому
Bang punya saya baut slebor bagian bawah yg patah, dan patahnya itu di dalam, seperti yg di video, klo pake cara seperti itu apakah bisa?
@artsontopРік тому
Left handed drill bit is always my first option. Has worked more times than I would have expected.
@rick3914Рік тому
Yes ! the best thing is to use a small metal tube in which to pass the left handed drill bit so as not to damage the thread
@lewis2553Рік тому
Good idea, but left handed bits aren't very common. They're kind of hard to find, and I imagine they cost more than their regular right hand counterparts. Too, I'm not sure I could get used to sharpening a lefty. It would take some getting used to, for sure.
@randypond74994 місяці тому
Does the bit ever break?
@artsontop4 місяці тому
I don't recall ever breaking a lefty bit. I suggest a quality bit (cobalt, carbide, titanium coated at the least. Gentle pressure, low rpm, DRY, Very slight off center angle of attack. You want the bit to Bite and reverse the fastener. Screw extractior comes next if need be Good Luck!
@viktorwagner4721Рік тому
Очень интересно.Сверху закрыли тряпкой,чтобы струшка не попадала на на детали при нарезки резьбы.Но стружка то падает вниз.Ребята-будьте внимательны,особенно,когда продуваете сжатым воздухом остатки стружки.Рекомендую вам,просмотреть ваше видио самим,как это всё вы делали.
@aibarakupov8990Рік тому
Правильно.
@alsteeves2044Рік тому
Can't understand the thinking behind the procedure. Was happy to see the rag come out, but couldn't believe how it was placed.
@user-lb8lh1xy7mРік тому
видео из ряда - лишь бы что-то....такую шпильку и обломать, надо лошарой быть
@larrygooch62333 місяці тому
The first one might happen once or twice in a life time.the second one I've done 3or4 times in my life,works when your lucky enough that the stud is loose in the thread.
@JohnDeereR-zw3wjРік тому
One of the best ways to remove a broken stud is with a left hand drill bit. More often than not the drill bit grabs the stud and backs it right out. I have to do this almost every day taking stainless screws/bolts out of either aluminum or stainless holes and sometimes cast iron.
@jimthompson3030Рік тому
I have done this also .. if the bolt is broken off seldom easy to back out!!!!
@mrtopcat2Рік тому
Exactly. Plus this video seems unreal. Left over broken bolts are rarely this loose in the thread. I saw an awesome method to center the bore exactly in such case: use a door hinge centering drill 'bit' to start the whole. Then you can use the left hand drill and easy out if necessary.
@kf5hcr176Рік тому
Agreed, and or a left hand tap. I get mine in HSS from the local bolt supplier
@johnmcclain3887Рік тому
I've been working as a mechanic fifty years and breaking a bolt by over tightening often leaves the broken piece loose enough to work out this way. The hardest to remove are almost exclusively broken because of corrosion locking the threads to the aluminum. I would agree, using every possible advantage is the best way to least impact the strength of the aluminum threads.
@savage22bolt32Рік тому
I have used this method many times. When you don't have a left hand twist drill.
@conniecostner96657 днів тому
Thank you I just broke one of the bolts off the magnita on my pushmower working on the flywheel. My homeboy let me take the bolts off and the first one I took off I broke it LOL
@nrg5636Рік тому
Очень познавательное видео, от души посмеялся, а ещё больше от комментариев 🤣🤣🤣
@user-bt9xf1ew7h10 місяців тому
Точно ❗️ Комменты - 👍👍👍
@cheditulush3665Рік тому
Я чуть не заплевал увидев ногти
@anthonykinrade86423 місяці тому
You placed a cloth around the broken stud to stop swarf going into the engine and then proceeded to blow the swarf into the engine with the air line!😅
@maxapollo18 місяців тому
try that when exhaust mainfold bolts break off in the head not happening
@user-sm4zl4pu9pРік тому
Надо же, а баба просто супер. Мужик бы ни за что не догадался😂
@vladimirbogatkin8073Рік тому
Ваш юмор оценен по достоенству ! Спасибо!
@sanyapatrashkin1876Рік тому
Для таких обломышей и по сложней очень помогают свёрла с левым вращение.
@robertmiller2015Рік тому
Where can I get that tool from I need to do this for my car
@DanielRamirez-vi8nqРік тому
Depende donde este El birlo capado Si es uno que esta en el múltiple de escape O si esta cerca de paso de agua que se haya oxidado Par esos son diferentes formas
@uklonist9301Рік тому
Хорошо бы посмотреть как будут выкручивать упёртый с торца обломок калёного болта.
@user-xt1sw3zl2tРік тому
Ногтём легко:)😂
@s.o.s.exploration2412Рік тому
Some people add a little bit of bearing grease in the shred collecting portion of the re-threading tool. This way it lubricates the cut and collects the material keeping it in that gap rather than it slipping between or rubbing into the threads.
@ayubshaikh9156Рік тому
Right ! Grease is better.......
@Dannysoutherner5 днів тому
Backwards turn drill bit will often spin those right out. The punch method I've used often as well.
@ivankhov45758 місяців тому
А если резьбу нарезать левостороннюю вкрутить болт и выкрутить ?
@user-fl3xu1ij7tРік тому
Попробуй постучи кернышком по обломку шпильки в выпускном коллекторе двигателя, или по обломку свечи в свечном колодце. Экстракторы разного диаметра не дураки придумали!))
@user-xr2ze6gv1wРік тому
Ни один экстрактор ещё не смог выкрутить ни один нормальный заломышь. Только сварка или сверление.
@user-fl3xu1ij7tРік тому
@@user-xr2ze6gv1w Шпильки выпускного коллектора, обломанные под корень, нормальные обломыши?
@user-xr2ze6gv1wРік тому
@@user-fl3xu1ij7t их не выкрутишь экстрактором
@user-fl3xu1ij7tРік тому
@@user-xr2ze6gv1w Может мы о разном говорим? Экстрактор, это такой винт с левой конической резьбой. Сверлишь в обломке отверстие нужного диаметра, ввинчиваешь в него экстрактор и ....
@user-xr2ze6gv1wРік тому
@@user-fl3xu1ij7t и в момент вкручивания экстрактор расширяет обломыш,и он ещё сильнее закусывает. Пробовал, знаю.
@user-sh6nb8ie4fРік тому
Мастер крут .Так могут только парни с такими ногтями.
@pieterpocica7 місяців тому
Jaki to silnik , marka ?
@multikmodes62Рік тому
A lot of you don't seem to understand this was just to show you the technique, not what he probably would have done normally. It was just a demonstration, created for whomever might benefit. Now you know....
@sulac4244Рік тому
Уникальнейший способ! Просто Шедевр в сфере технического решения.
@maxtitov4245Рік тому
Вот это трюк, сума сойти!😏
@user-bh8je5pc6f7 місяців тому
Да , тяжелый случай ! Давно я так не смеялся ! Думал как же он его выкрутит ? 🤔А он и сам вывалился . 🤣
@Dmitriy7697 місяців тому
А куда делся обломок болта в отверстии? Чтобы туда засунуть метчик нужно его высверлить
@user-be9dg2uk3cРік тому
В бытность работы мотористом частенько отламывал болты (особенно у зил-120?) на головке блока , но ни разу при отломе, отверстия там не было, чтобы нарезать резьбу. И приходилось сверлить, потом забивать что-то твёрдое и выкручивать Ну или же иметь сверло, может метчик левосторонние.
@user-mk6qu4zs3qРік тому
ЗИЛ 120 ? Что за зверь ???
@user-cx8fi8wu2vРік тому
Обломок *болта* - далеко не то же, что обломок *шпильки:* в торце первого можно просверлить 2 отверстия под плоскую отвёртку с вырезом - а в торце второго придётся сверлить *осевое* отверстие для экстрактора (негодного метчика со спиленными на косой клин зубьями).
@gewelryamator42528 місяців тому
При Союзе про экстрактор и не подозревали , сверлили отверстие и забивали заточенный трехгранный напильник .
@user-cx8fi8wu2v8 місяців тому
@@gewelryamator4252, напильники делают из ОЧЕНЬ хрупкой стали - У13А, которая ПЛОХО работает на скручивание: из трёхгранных напильников делали *шаберы...*
@andrejshamin14527 місяців тому
@@gewelryamator4252ну конечно. Я работал в АТП, в иструменталке был комплект вывертышей, однажды я взял такой со стола перепутав с обычным метчиком и так узнал об их существовании)
@user-nn3cz3lh9uРік тому
Слава Богу , что я не один подумал о том ,что он ногтем вывернет😂а оказалось - клювом!
@idaajimotor5012Рік тому
Itu besi yg runcing itu besi bekas apa bang
@billythekid9694Рік тому
O truque, afinal, não é tão simples como parece, caso o parafuso esteja bem firme dentro da rosca. E geralmente parafusos quebram justamente por estarem presos na rosca. A melhor maneira é usar um punção e marcar o centro do parafuso e depois ir furando com um broca fina (de widea, melhor) e enfim usar um extrator se necessário, já que às vezes dando reverso na furadeira (bem devagar) a broca "engancha" no parafusos e este sai numa boa.
@johndough9187Рік тому
I use a left-twist bit.
@nelsonlouresloures7735Рік тому
Era bom que fosse assim tão fácil! 😂😂😂😂
@mariuszmaek3286Рік тому
Poczekam z rok jak mi urosną takie pazury to też tak będę czarował!
@aseksan3684Рік тому
Też bym polecił nożyczki i w pierwszej kolejności obcięcie szponów
@onesiogomes1431Рік тому
Uso essa técnica há mais de trinta anos
@garyharding12612 місяці тому
What if you haven't got a Tap or Helicoil Insert ?
@user-mp5hk5yc7tРік тому
Попрбуй так вывернуть "закисший" обломок на выхлопном коллекторе.
@aleksandrdobrinin4714Рік тому
Таким когтиной? Да легко 🤣
@user-mp5hk5yc7tРік тому
@@aleksandrdobrinin4714 👍👍
@petrovich23ruРік тому
Что бы стружка при нарезании резьбы не сыпалась куда попало, и не выдувать ее потом компрессором, надо мечик смазать густой смазкой типа литол.
@user-ei9cm7bs1b9 місяців тому
Да не, чтобы стружка не сыпалась вниз надо тряпку сверху положить )))))