Thanks! Other tutorials say that it's just in the board manager, but it wasn't there, so this tutorial really helped me!

Kept getting an error, that there was no programmer. It must be a change in the IDE from this version. In the end, when uploading to the AtTiny via the programmer, do not use the usual "Verify and Upload" buttons, but enter Top menu- "Sketch", and then use "Upload Using Programmer". Worked like a charm after this! Thanks!

very well explained, and your accent was no problem, if only others were as clear as you are, thanks !

Very well explained; worked first time!

awesome video. Concise introduction, just what i was after. thank you and keep it up

You rock bro. It is working. Cheers from Amsterdam!

A wonderful video very interesting, I wanted to ask you if you could do a video tutorial with Attiny85 and 74hc595 in order to multiply the outputs of Attiny85 being able to manage 8 relays. Thank you very much for your attention I hope very much that you will do this tutorial.

0:32 Funny demo of usb interface, you never know until you try

slow down, take a breath, smell the flowers, and no more coffee for you today! great video with excellent information. i WILL view it again (and again) to get all the good info you have presented, thanks.

Nice video... Queries about what s/w you use for video editing & screen capture ?

Hello, Friend! I have this error: avrdude: Yikes! Invalid device signature. Can you help me?

Great video! this helped me finally have success programming an ATtiny85. I also think your white board you designed to expedite further programming removing room for errors during using jumpers.

hi, where should I put the folder Attiny programmer Shield ?

Excellent! Well done!

Can you program the ATTiny24/44/84 in that larger socket?

Awesome video. Thank you.

hello, I programmed attiny85 with Relay By Arduino But with its connected to arduino works But with the 9v Battery not working help me please . thanks.

Good tutorial, thanks.

i am getting this: avrdude: Device signature = 0x000000 avrdude: Yikes! Invalid device signature.

Bro in some videos they r telling to choose internal 8mhz nd burn bootloader bt same when i did it shown error . Why?

Hello my Friend...good video.. can i use the attiny85 for servo control?

thank you! So there is no need for a capacitor fpr programming?

nice video.. keep it up

Can you post the Eagle file for the project. Reason I am asking I would like to add capabilities to the board to make it more usable than just a programing board to ATTINY. Regards, Dana.

flawless

awesome thanks brother for board manager url.....this part is very hard...how's this possible been done by me, I don't know

merhaba yükleme yaparken "Upload error: A programmer is required to upload" hatası veriyor. Sebebi ne olabilir?

Well done

Good job! Thanks..

What program did you use to create the Schematic / Board layout?

nice one good video thank you

Ok I am confused, can the ATtiny85 read in analog input in reference to serial communication SCL and SDA ? Pins 6 and 7 I saw were not used.

Quick question: Is there a way to upload code from a hex file to the ATTINY using the Uno?

When I upload the arduino isp, I receive a fault. #Define SERIAL Serial Serial is not declared Whar do I do?

Is it actually possible to make a Universal IR remote? As far as I know, the IRremote library (which is brilliant for everything) can't run on the Attiny85. I'd be happy to be proved wrong because I'd love to make my universal remote even smaller

Where is the EasyEDA file located ?

keep it up

Hi Robbi you can add the link for the attiny as board?

Does this work with an attiny straight from the factory with no bootloader?

Are the Gerber files on Github the latest version ?

its confusing that you seem to turn the board around during the video

Can you pull the program written in it using Arduino?

i like the video you made, but you was going thru stuff quite fast, making it hard for a NOOB like me to keep up and follow.. i'd like to make a custom 4 led volt meter, where i can command the exact voltage before a led turns on. i have a non-linear hall sensor that i am to use , so i need to set custom turn on points, and have a small hysteresis as well.. if you have interest to help, feel free to let me know..

Thanks

Thank you very much! This tutorial worked perfectly! As of December 27 2017

How many times we are programme it?

"hey you guys rubby here"

Good #NMElectrical

প্রোগ্রাম দেওয়ার পর আরডুইনো ছাড়া এটাতে শুধু পাওয়ার দিলে কার্যক্রম ঠিকঠাকমতো করবে না???

I heard "Hello" and "Goodbye" was there something in the middle???

Capictor use karo

attiny board manager cont instol

What are ur Educational qualifications?? Bahi? Btw nic vid!!😘✌👏👍

Man I wish you would work a little faster!! I kept getting bored throughout the entire video waiting on you to tell us the next step. Sorry my brain can’t work that slow.

Slow down, you are trying to teach give us a chance to take it all in.

I have wasted MANY hours on this. ---- IT DOES NOT WORK using your connections, and IDE V 1.8.9 selecting "Arduino as ISP (ATTinyCore)" or "Arduino as ISP (ATmega32U4, ATTinyCore)". What the !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

slow down

you go too fast