Nissan LEAF P3102 clear with Leafspy Pro

Рік тому

Here's a quick guide on how to remove the P3102 Invalid Battery ID DTC that appears after replacing a LEAF battery pack. This is done with the normal Android version of Leafspy Pro
After a direct battery swap or batter upgrade has been performed, the only thing preventing you from driving the vehicle is a check EV warning light along with turtle mode. To clear this code and remove turtle mode, simply read DTCs and perform a P3102 clear with the latest Leafspy Pro version (min version 0.46.172 for Android) (min version 1.7.44.15 for iOS [Requires TestFlight]). That's it, enjoy the newfound range!
For more info on battery swaps/upgrades see the FAQ on the mynissanleaf.com discussion forum: www.mynissanleaf.com/viewtopi...

КОМЕНТАРІ: 22

@atlarcticair1338 8 місяців тому

Is there any other way to reset the UV warning light?

@Koori27 Рік тому

Have you managed to unlock the full power of the 160kw inverter yet? So you can push it to the limits once that yoou fixed the pack?

@xdellavedova Рік тому

wait for BMS reset after repair battery or replace defective battery module

@Patchworkdaddy007 Рік тому

I knew it! If somebody fix this problem it will be you!👍👍👍👍👍👍🇪🇺🇺🇦🕊️

@rjung_ch Рік тому

Could you get your bigger battery to balance up as well? 👍💪✌️

@DalasEVRepair Рік тому

Working on it! :)

@rjung_ch Рік тому

@@DalasEVRepair good luck on it.

@andreybalanchuk8387 Рік тому

Hi Dala. I didn't find if LeafSpyPro can clear "frontal collision" error in gen2? All info I found says I need to take module out, remove chip, get flash from it and correct one bit then flash it back, solder back etc.

@DalasEVRepair Рік тому

I suggest the mynissanleaf.com forum!

@andreybalanchuk8387 Рік тому

@@DalasEVRepair that is what I did already. Didn't find any leafspy entry for SRS. I'll ask program author, anyway had a question why dashboard shows significantly different soc than leafspy (set car properly in settings).

@W4rH4wkXX Рік тому

👍👍💪💪

@garygauthier1551 Рік тому

I have just bought a 2023 Nissan Leaf Plus , and tried to use the onboard timer to charge the battery to less than 80% by setting hours of charging. What I also have is a 40 amp Clipper Creek labeled SunCountry charger here in Canada. When I got to the car next morning the car was in a loop of starting a charge with a beep with charger contactor connecting and then instantly stopping every few seconds! Because the battery was at 100%. I tried this method two different time with the same result. Check with LeafSpy pro and now my L1/L2 shows 6900 charges. My question is can the L1/L2 charges be reset to 0 ?

@DalasEVRepair Рік тому

Yes we have it figured out, here is an example Battery request and response: 79b 02 21 62 00 00 00 00 00 7bb 10 76 61 62 08 00 01 5a QC = 015a L1 / L2 = 0800 Write to VCM: 797 02 10 c0 00 00 00 00 00 79a 02 50 c0 00 00 00 00 00 VCM response 797 04 3b 14 08 00 00 00 00 79a 02 7b 14 00 00 00 00 00 VCM response 797 04 3b 15 01 5a 00 00 00 79a 02 7b 15 00 00 00 00 00 VCM response

@garygauthier1551 Рік тому

Thanks for the quick reply! But to access the VMC is through Leafspy Pro ?

@DalasEVRepair Рік тому

@@garygauthier1551 No for this nonstandard procedure you will need dedicated CAN sending equipmemt

@garygauthier1551 Рік тому

@@DalasEVRepair Thanks Dala greatly appreciated!