Awesome! Very exciting stuff!

Thanks for the video! In this example, are the server nodes communicating with one another?

Hi, Many thank for this nice App! I want to know how to configure a relay node in BLE mesh. Is there any video to introducing it? Thank you!

Hello! Thank you for this useful tutorial on the nRF Mesh App. I have a question: is there any set-up that needs to be made before using the app with the Thingy boards? My app does not find the boards and I am not sure why. Thanks!

Hi, Thanks for the sharing!!! I have some questions about the Thingy:52 firmware I've followed the step which is provided on the Github page. But when I compile the project(Mesh_2.1.1\examples\light_switch\thingy_provisioning_demo_generic_OnOff_BLINK\light_switch_proxy_server_nrf52832_xxAA_s132_6_0_0.emProject), there is 20 errors. From the output windows , it seems several functions are undefined. But I haven't modified it. I just followed the step and rebuild it. Did I miss something?

can we attach sensors to this device......i mean can we use the i2c or the spi communication protocol in this case?

Awesome.. Great one.. Can i implement same with Nordic Thingy 91?

Hello.. where I can find the firmware side code in nRF Thingy used in the above video??

Hello there! Is it possible to send configuration data to nodes automatically after provisioning? Thanks, looking forward for your response.

I got 3 Thinky 52 and I'm trying to connect them as shown in the video (I have an android phone) and It is not working. Can you help me, please?

Is it possible to make it work on the nRF52840-Preview-DK?

Hello would you please post the code for the firmware.

Hii sir, sir, i am Sending a data from ( NRF24L01 transmitter) to ( NRF24L01 Receiver ) Using Aduino Uno. but i want to put its Nodes ADDRESS in DECIMAL format like - ( this_Node = 12345 , Other_Node = 31296 ) . but the problem is.... , in Decimal format addressing , Data is unable to Send in my code . ( i think there is Addressing problem in my Code ) . I Had mail you my codes on your email i had also attached my code below , Sir please Help me to Correct the Code . i will be too much thankful for your Help & Suggestions .................................................................... TRANSMITTER CODE .................................................................... #include #include #include #define button 2 RF24 radio(10,A1); int buttonState = 0; RF24Network network(radio); const uint16_t this_node = 12345; const uint16_t other_node = 31296; void setup() { Serial.begin(500000); SPI.begin(); radio.begin(); network.begin(90,this_node); pinMode(button,INPUT); } void loop(){ network.update(); //---------TRANSMITTING----------// RF24NetworkHeader header(other_node,DEC); unsigned long buttonState = 311; bool ok = network.write(header,&buttonState, sizeof(buttonState)); Serial.println(buttonState); } ............................................................................................ RECEIVER CODE ............................................................................................. #include #include #include #define led 3 #define led2 4 RF24 radio(10,9); byte guest=0; //#define buttonState1 8 const int buttonState1 = 311; RF24Network network(radio); const uint16_t this_node = 31296; const uint16_t other_node = 12345; void setup() { Serial.begin(500000); SPI.begin(); radio.begin(); network.begin(90,this_node); pinMode(led,OUTPUT); pinMode(led2,OUTPUT); } void loop(){ network.update(); //---------RECEIVING 1 ----------// while( network.available() ) { RF24NetworkHeader header; unsigned long buttonState; network.read(header,&buttonState, sizeof(buttonState)); Serial.println(buttonState); if(buttonState1==buttonState) { digitalWrite(led,HIGH); digitalWrite(led2,LOW); } else { digitalWrite(led2,HIGH); digitalWrite(led,LOW); } } }