See Thru Engine on New Turbo Got Boost? (Nitro & Dyno)
Переглядів 3,343,672
5 років томуIn this episode I take the see-through Engine with the turbo to an entirely different more extreme level of insanity, by injecting nitromethane directly into the engine without a carburetor or any obstructions, literally wide open throttle while on the dyno While Filming it in 4K Slow Motion .
this engine has taken an unimaginable amount of abuse through the episodes, and in this episode and made the most horsepower it has ever made as well as hit the highest RPM in history for this engine.
in the next episode after this one I will be installing a proper electronic fuel injection system, we will be able to control the amount of fuel timing and boost all while measuring horsepower.
check out the previous episodes in the series playlist as well as the links below.
MS3 Pro EFI System: bit.ly/Megasquirt-AMP-EFI-Warp...
Previous episodes:
See Thru Engine on Turbo Nitro and Dyno (How much HP does it make?) E.5 • See Thru Engine on Tur...
See Through Engine on NITROMETHANE 4k Slow Motion ( S1 • E4 ) Blow Up Attempts 1 -9 Crazy ! • See Through Engine on ...
Directed By: Matt Mikka
@alansartrignot 4 роки тому
What is nitromethane exactly?? And what allows it to turbo boost stuff?
@minhvuongnguyen5014 4 роки тому
Good job bro
@mftuning2891 4 роки тому
There is another turbine on the turbo that is on the exhaust side and the turbo gets spun by the exhaust fumes rushing out the engine and there for spinning the turbine at the front that is sucking in more air into the engine. And with more air you need more fuel and more fuel and air=more power.
@drakevelazquez8728 4 роки тому
Nitro Meghan e85 pump gas 93 or jet fuel has a higher octane rating that prevents the engine from detonation or pinging that is like tiny tnt bombs in your engine. That’s no good and will break your internals let alone give you less performance. A clean engine creates a fireball that pushes the piston. Down turning it into torque than horsepower allows you to add more timing and boost that nets you more power
@EATSLEEPDRIVE2002 4 роки тому
Wow dude
@spenck7740 4 роки тому
Nitromethane is just a different type or fuel, you can turbo charge an engine with any fuel, im not sure why hes using Nitromethane but its really irrelevant as far as you should be concerned. It sounds like you dont know much about engines but thats okay!! Do some research and learn more and you might find yourself like me; addicted to cars and passionate about building engines
@my1little2pony 5 років тому
In this episode watch as I spray nitro methane all over everything
@WarpedPerception 5 років тому
😂😂😂..lol. yes !
@bigv6724 5 років тому
Big fireball Anyone bring marshmallow?
@GoodlookinMug 5 років тому
A large part of me was hoping this would end with loud sirens from several firetrucks. Dude, your Moms gunna be so pissed lmao
@betoborba3329 5 років тому
I’m just trying to help not being a d%#! but you are shooting way to much fuel so you are slowing the engine so the engine can not build rpm and boost, if you look on the run that you got the 7400 rpm that’s when you had the the closest mix that’s why the rpm went up about the boost the best way to get boost is to put rpms and then put some load and you will see boost! I want to see this thing working and building boost just trying to help!!
@kennysboat4432 5 років тому
im pretty sure unless you get it warm or really really airrate nitro methane its like diesel and wont catch on fire too easily.
@madazz01 5 років тому
Mate the turbo is fine, you need a 28mm pitbike carb in front of the turbo, an old fuel pump to supply oil pressure to the turbo so it can actually spin, and mix 10% nitro with normal fuel. Then she'll boost. Drowning tho whole thing in liquid aint efficient.
@JefeInquisidorGOW 5 років тому
This. You need oil pressure if you want to make boost
@VikingRul3s 5 років тому
@@JefeInquisidorGOW No you don't. The oil pressure is for lubricating the turbo, not actually making boost. But yeah, without it the turbos aren't gonna last very long
@VikingRul3s 5 років тому
In front of a 50cc cyl 4-stroke? Nope! Even in front of a 70cc 2-stroke that's gonna be hard to get a fine mist out off. Pro GP teams where doing 34-36mm on 125cc bikes pushed to their absolute limit. Yeah the turbo adds some more flow, but at 2 psi that's only 15%, so a MAX 21mm carb and that should be sufficient to even do 7 psi on a 50cc, with ease! Jetting is the name of the game here and likely boring out the feed "tube" to max capacity (as i don't think hi've done that yet, should have been done at the ethanol conversion), not "bigger is better" US approach
@madazz01 5 років тому
@@VikingRul3s Cool sounds good, any carb you like, carb size is kind of irrelevant here, you just need one. The turbo also needs oil "pressure" to act as bearings so its spins. Jetting will just be a bit of trial and error, I ran my 135cc lawn mower for years with a 28mm pitbike carb and it was fine, people are riding 125's right now somewhere with 28mm carbs, but i think you probably should start with a smaller carb and play from there. Btw that motor doesn't look like a 50cc, more like a 150cc on video.
@VikingRul3s 5 років тому
@@madazz01 Yeah, that's what i meant with "lubricating the turbo" in the comment above. I just dumb it down a bit so none-gear heads can understand it 😊 28mm on a 135cc seems way better! Carbs can actually get to big, if you throw a too big on, the misting from the jet is gonna be weak and inefficient, so loss of power. But yeah, it's not like a 28mm on 50cc will complete kill it, it'll still run, though the mixture may be quite lean. I could be wrong about the engine size, for sure!!! It's just a guess, I just assume it's 50cc because of the rated bhp, 2,5-3 is the smallest mover engines here, usually around 50cc. But i'm from EU, not sure mover engines are similar in USA 😊
@MichaelTheRead 5 років тому
"I'm just gonna spray the nitro-methane directly into the turbo..." Mad Max: Fury Road style!!! YEAH!!!!
@WarpedPerception 5 років тому
I wish I could hit the like button 10 times on this comment. At least someone knows how to have fun
@harleetuttle799 4 роки тому
Mad max would have "baby birded" that nitro
@sinewave3323 4 роки тому
My favourite run was the run u liked the most to! The sound was awesome! It reminded me of when i used to moe my lawn lol cause i rigged a shoe lace straight to the throttle so i could over ride the automatic govoner so i could have fun reving it as i mowed the lawn!
@c4pt1n54no 5 років тому
Yeah you used 48oz of nitro in 2 minutes but half of it is on the floor
@dadigitechmanjunior 5 років тому
And When you're fuel mixture is literally coming out of your exhaust pipe
@MitchellGuyon 5 років тому
More than 1/2
@roodgeregeld 5 років тому
And in the oil
@clintonfronterhouse7484 5 років тому
@@dadigitechmanjunior I can't believe that it didn't blow up! All that raw fule next to an open exhaust and an overheated engine. Where is the fire ext?
@MAGGOT_VOMIT 5 років тому
*His concept is wrong. You can't build boost pressure without a load on it. Plus liquid doesn't burn, Vapors do. He should be shooting Ether in it, not drowning it.*
@HWGuy1337 5 років тому
Ep3: this thing is dangerous, it will blow the engine apart, I am taking all the precautions Ep 6: badAss manual nitro spraying
@helmysetiabudi9915 5 років тому
I agree with you
@kierenalvarez 5 років тому
Was waiting for a fire haha
@TRX450RVlogger 5 років тому
who cares it’s a hell of a lot of fun to watch and to do this kind of stuff.
@JHuffPhoto 5 років тому
Yea dude I hope you are prepared for the hospital run when this thing blows. I couldn’t quit watching. You were using way too much fuel.
@KrustyKlown 5 років тому
@@kierenalvarez the loose spark plug wire connector on see thru head .. can't believe the whole thing didn't go up in flames, LOL!!!
@PawanKhandale 5 років тому
Hello sir, i am huge fan of your see through engine videos, it’s helps a lot to understand how engine works. I have one request for you, can you please make a video (see through) on variable valve timing .
@scootergeorge9576 5 років тому
Getting the proper mixture as well as fuel atomizaton should be an enormous help. Looking forward to seeing it.
@Catrik 5 років тому
Biggest relief ever when you show that new turbo and Im like NOOOOOO I DON'T WANT TO WAIT FOR NEW EP. Then I notice the video is only half way through and realize we're gonna see it run right now!
@WarpedPerception 5 років тому
Lol... Thank you
@yellowhelmetracing4576 5 років тому
@@WarpedPerception what was that 2nd turbo? I kinda wanna get it and would like to know the name/where to get it.
@Hankbob_Hillpants 5 років тому
I have one of those 3 hp Briggs engines(from 1979), the cam holds the intake valve open for most of the compression stroke to make the engine easier to start, if you were to shave the intake valve stem, or the the side of the cam lobe that is enlarged you would probably be able to make a lot more power
@jonrudin 5 років тому
45 oz.? You were spraying nitro everywhere bro
@AqueleDoHonda 5 років тому
It's so cool to see the things you do every video you make makes our jaw drops more and more like in a cartoon , thank you for everything you do.
@WarpedPerception 5 років тому
Thank you, I'm definitely going to try and pump out more videos big and small on this channel.
@VetteTTV12 5 років тому
Consider adding an oil pump for the turbo. Since it's most likely not ball bearing it needs oil pressure to "float" in the oil and spin freely like its supposed to. Also, consider a twin cylinder so the turbo isn't free spinning between exhaust strokes. This will help to maintain and build boost. For inspiration or ideas, the Ruckus Scooter community has successfully turbocharged several of those engines and if memory serves they're 125 or 150cc engines.
@phantom240 5 років тому
The ruckus is actually a 49cc in stock form, though most people do swap 125's and 150's on them.
@MixaL1s6804 5 років тому
how can it be better if he adds an oil pump for the turbo? since it had lube then if its in engine oil it wont make a difference? sorry if im mistaking.
@phantom240 5 років тому
MixaL1s6804 The way a journal bearing works, it needs a proper oil film to float and reduce friction. This usually requires flow and pressure. But in this application, eh probably negligible
@kleetus92 5 років тому
@@phantom240 Maybe... but when the oil starts bubbling out of the feed port looking like silver paint, I'm betting whatever bearing WAS in there, ISN'T any more.
@VetteTTV12 5 років тому
@@kleetus92 you get it. MixalL1s6804: phantom240 said it well enough, but it does matter, a lot. The center of that wheel should be spinning at close to 100k-200k rpm and will be completely destroyed without "floating" in the oil. If you really want to know what's going on I emplore you to Google how bearings work in an engine or turbo. There's just too much information to answer the why in detail on here. But to address the oil in the crank case, it really should be cycled and filtered to pull that nitro and water out because its hurting performance with the way it is now.
@ProjectFarm 5 років тому
You've got a thumbs UP from me! Great job--love the setup! Looking forward to the next episode!
@WarpedPerception 5 років тому
I was just talkin about you the other day, I had a great idea, I was thinking about sending you one of my see through rotary engines.
@WarpedPerception 5 років тому
THANK YOU, you as well, keep up the good work, don't even change anything you're doing because right now you're killing it.
@ProjectFarm 5 років тому
I'd LOVE to test one of your see through rotary engines! That would be amazing! By the way, the production quality of your videos is absolutely amazing, which makes them very enjoyable to watch! Thanks again for all the time and effort you invest in the videos.
@WarpedPerception 5 років тому
@@ProjectFarm thank you man !!. I am trying to get one to you soon.
@jacobmollernielsen7198 5 років тому
Hello peoject farm!
@eddiesanchez86 4 роки тому
Gotta love when someone who has no idea what they're doing tries something stupid.
@someonesomewheresomdeday 4 роки тому
so the last 22 minutes of my life.
@zungruitelbitladnaternoche7305 4 роки тому
How can he calculate the fuel consumption when most of the fuel goes everywhere but in the engine? His sprayer doesn't even vaporize the fuel.
@zungruitelbitladnaternoche7305 4 роки тому
@Johnny Steffy It's not "trial and error" when you throw fuel everywhere then say "I used X amount of fuel". He has no idea how much fuel went in the engine. You're a moron, worse, you're a lesson... Get it? I surely doubt it...
@zungruitelbitladnaternoche7305 4 роки тому
@Dave Micolichek You didn't even watch the video. You said it yourself "inside". He's spraying a lot of the fuel "outside" where the fuel is wasted completely and has no effects on the performance of the engine. That's what We are talking about dumbass and yet you run your mouth like a troll. Go ahead and watch the video again and you'll see how much of a moron you really are. If you are smart and a little bit humble, your next message should be apologetic. Then I'll recant my judgement upon you. Or stay stupid and laugh.
@zungruitelbitladnaternoche7305 4 роки тому
@Dave Micolichek My statement still stands. The word wasn't right but it doesn't make my statement wrong. It's just in the after note. You're just a troll, you can't even spell right and your syntax is terrible. You accuse SOMEONE (not "some one") of "talking smack" yet it's just a diversion to put them on the defensive to keep them from noticing you're doing the same exact thing. If you have any pride whatsoever you should feel pretty stupid to be schooled by someone who started to learn English in their 20s as a second language. But I think you're deluded by your sense of superiority. Which is common to Morons (i.e. someone with the intellect of a 9 to 12 years old, as an obsolete medical term yet very adequate to describe you). Hell, are you at that age? Sorry, you didn't fool me buddy.
@bioweaponsystem154 5 років тому
It's great to have the See-Through cylinder head so you can see what's going on in terms of combustion. The right mixture was the key to good operation. Unfortunately, the turbo was lacking a proper oil line and with all that extra metal that came out with the oil, I wonder if a proper synthetic oil was used. Also, seeing as how you're increasing loads and adding on the turbo function, I wonder if you need a proper oil circulation system complete with a filter. Obviously a little overboard but that would keep contaminants out of the crankcase.
@jaybomb5022 5 років тому
Lol most accurate fuel consumption math I've ever seen. 44oz.....28 of witch ended up on/around the surrounding floor not burned. Great video for the curious!
@WarpedPerception 5 років тому
I wish I could love your comment twice, very well stated
@MrVolodymyr 5 років тому
that was additional cooling)))))),
@buddylee19082 5 років тому
That "mechanical fuel injection" was pure comedy! I have laughed like that in AWHILE! Thank you for that bro you just made my day
@WarpedPerception 5 років тому
Same here, I'm glad at least somebody got it, I think you're the first out of 200,000 people. When I did that I was laughing pretty hard, when I watched it I was laughing my a** off. It was a last-minute idea but I knew it was going to be funny and it actually worked, kind of. I always go with the flow but it did give people a good example carburetor vs. Fuel injection, especially once it's compared with the next episode where I do proper fuel injection.
@WarpedPerception 5 років тому
Even the one part where I spray the whole turbo down before I start it, I did that on purpose but almost nobody who watched it got it.
@buddylee19082 5 років тому
@@WarpedPerception I got it right away and I was ctfu the whole time! Thanks again. I wish more ppl had the same sense of humor!? Great stuff man, keep it up!
@toddsimone7182 5 років тому
More like "manual injection"
@WarpedPerception 5 років тому
@@toddsimone7182 hahahahaha... that's how I conceived my children by " manual injection" very reliable system
@gtrulez 5 років тому
I like that little engine. Though as hell. No matter what you do it just keeps running. Love to see the efi work on this. It has potential. Im sure it could make a bit more hp.
@JarretLaMark 5 років тому
@ 9:33 It's like a turbo motor money shot! Love it! Thanks for doing this series. It's very entertaining as a gear head and large scale gas RC enthusiast. Currently adding a crank driven supercharger (made by RBInnovations) to my 2 stroke 30.5cc 5th scale RC Baja 5b buggy. Should be interesting. Watching these videos has got me itching to wrap that build up, get it tuned, and then let her rip. Thanks!
@theroadkilledchicken 5 років тому
As you probably know, most turbos wont spool till you load the engine. It should also do a lot better if you get a carb off a bigger engine, say a 420cc and mount it in front of the turbo for a pull thru design.
@WarpedPerception 5 років тому
There was always load on the engine here except for a couple of runs, but I did keep a small load at all times on this engine except for 2 takes.
@theroadkilledchicken 5 років тому
@@WarpedPerception I see now, changing the angle of the dyno brake thru me off some how.
@loligagger85 5 років тому
a carb will never work, spinning the air and fuel takes it out of the air and back into liquid droplets too big to burn properly.
@Phil451 2 роки тому
Most engines won't spool a turbo unless they're under load. The turbo can spool regardless of whether on not there is any load, it just needs pressure from the exhaust.
@michaelpeters6012 Рік тому
I hate you for this lol. It was annoying watching you just spray and spray in the turbo
@jasonhuber3236 5 років тому
Use a multi piston engine (like a 2 piston) if you want to spool even the tiniest turbo. Having oil pressure on the journal bearing actually helps it spool to the designed RPM as well FYI (takes that small amt of play away you feel when moving it by hand.) Retarding the timing helps to spool any turbo as well. This video would have been REALLY COOL if you were able to spool up 10 - 20 psi. Maybe get 1 actual fuel injector and rig it to pulse like it normally operates. That will give you a great mist pattern for the most complete burn.
@Super1337357 5 років тому
I like how you removed your middle finger to clear the disk on the back of your phone.
@autodomeptyltd3156 5 років тому
Try lpg gas,, you might be able to regulate the right amount simply by using the right injector size nozzle, You can increase gas volume by a valve.
@juliansaiz5714 5 років тому
2 psi out of a 3hp engine and 7.2hp is really good that’s like 150% efficiency with the addition of a turbo
@EngineEngineer 5 років тому
wtf?
@ThePookybear56 5 років тому
not actually efficiency... just more power. Doesn't mean its actually making better use of the air and fuel
@juliansaiz5714 5 років тому
SIMPLE HUMAN bruh lmao you dumb
@ThePookybear56 5 років тому
Julian Saiz it's literally impossible for an engine to reach 100% efficiency
@PleaseGiveMeDonate 5 років тому
Engine effenciety is like how much heat you can get of buring fuel Effenciety for this engine it's like a i dont know maybe 40%... of all burned fuel I just mean you can't say that making more power it's making it more efficient becouse you adding boost pressure and more fuel to the engine. Effenciety still is on the same level
@Freizeitflugsphaere 5 років тому
Wow really amazing slomo footage! I really enjoyed that episode, keep up the great work! Just one question, which slomo camera are you using?
@WarpedPerception 5 років тому
We use a variety of high speed cameras, more important than the camera is filming technique.
@LinuxJedi 4 роки тому
Literally dumping fuel everywhere “Ya this will work” 😂
@ColdSmokes 4 роки тому
I've never seen more ambition toward a absolutely futile cause in my life...Five stars!
@WarpedPerception 4 роки тому
Lol... Well said !
@JSMachineWorks 5 років тому
You're drowning the engine big time! No wonder it won't spool up and make power
@WarpedPerception 5 років тому
That's the only way it will stay running, it's nitromethane, it needs a lot more fuel compared to gas.
@ModMotorMayhem 5 років тому
an engine will need nearly 5 times as much nitro vs gasoline to run anywhere near stoich, which allows an engine to burn a ton more fuel which = power. nitro has it's own oxygen atom
@jody6183 5 років тому
You can see it was too rich with the clear head as it wasn't firing half the time......
@JSMachineWorks 5 років тому
@@jody6183 exactly
@mustafayigit726 5 років тому
@@jody6183 Are you kidding me?? It's a 4-stroke engine..
@jimevans1809 4 роки тому
Watching this channel is like watching NASCAR: I’m just waiting for the carnage.
@martprice7726 3 роки тому
Looks like a hell of a fire risk all that fuel all over the place hope you got a good fire extinguisher. Good looking inside the engine running. Well done.
@Rudabaugh 5 років тому
"Is the engine fuel efficient!? Of course it is!! This old girl nearly gets 5 gallons to the mile!"
@pw383426 5 років тому
I am one of the silly people that have spent thousands on turbo charging a single cylinder (my raptor 700). You learn multiple cylinders is key to dependable boost and turbo reliability. Turbos don't like the sudden exhaust pulse every 720* of crank rotation
@Jessersadler 5 років тому
Spray fuel into the exhaust before the turbine.
@dylanhart4930 5 років тому
Also 2 stroke engines won't use the boost much. The exhaust valve is open when boost should be building in a 4 stroke engine.
@dizzytheokapi8114 5 років тому
@@dylanhart4930 A Raptor 700 is a four stroke.
@dylanhart4930 5 років тому
@@dizzytheokapi8114 well, that's fine. But this video is about a 2 stroke. That is what I'm speaking about.
@HavokTheorem 5 років тому
@@dylanhart4930 No, no this video is not about a 2 stroke.
@rotax636nut5 5 років тому
One of the most dangerous things I've ever seen, GREAT, more more!
@WarpedPerception 5 років тому
Thank you, best comment ever...LOVE IT !
@joshjendreas3645 4 роки тому
"My goal is to make this thing come apart, blow it up" as he stands right next to it sprayin her down with nitro from a pump sprayer.... This is either the luckiest guy in world or there is a god and he loves stupid people. Careful what you wish for.
@masriyono255 5 років тому
They work with passion.. My Respect 👍👍
@flaplaya 2 роки тому
Next level stuff. Definitely need one for my ho cart.
@ATLASGAMINGApallo 5 років тому
When you're 3hp motor needs efi
@nicolalio4633 5 років тому
I don't think EFI would work with nitro methane. The best option would be to buy a methonal injection kit and use that as a forced metered orifice. That will work better than the spray bottle. The EFI would not have a strong enough driver to run a upgraded fuel injector.
@ATLASGAMINGApallo 5 років тому
@@nicolalio4633 It would probably work just fine I think it's just funny as hell putting an efi system on a 3hp engine
@nicolalio4633 5 років тому
@@ATLASGAMINGApallo it's not a bad idea. i have a super chargerg 6hp. I have had to place a spark box in place to advance the spark by 50°.
@karlchallis 5 років тому
I think it needs someone who knows what they are doing :)))))))
@brunolouis5814 5 років тому
Your*
@brandonhightower5666 5 років тому
When a gentleman with missing digits says "Don't try this at home" you should probably listen. I wonder if nitro would make a 2-stroke blower move more air?
@vancemacd6315 4 роки тому
I love the dedication to these tests. Really great work. Thanks
@WarpedPerception 4 роки тому
Thank you !
@cpfpv6410 5 років тому
killing it bud. great video. Looks like a lot of work for one video. but I appreciated it
@ZepolWorkzGarage 5 років тому
A awesome video don’t worry about the people put the thumbs down you got thumbs up for me. Keep doing what you’re doing. I’m a Diesel Mechanic love these videos especially rotary ones. The way slow down combustion cycles with see thu head is the best. You should try some Nitrous LOL.
@MrWip3out 5 років тому
Interesting video. With the see through head there was a time when there wasn't much liquid in the head. I believe the motor ran best then. Maybe with the stock head you were adding too much manual fun juice?
@erichoffman1589 5 років тому
Don’t talk about proper mixture while using a pesticide sprayer as a carburetor. SMH 🤦♂️
@jacknickolstine3355 5 років тому
Lmaoo
@lanceuppercut6168 5 років тому
I was thinking maybe he can us a paint gun on a low air setting to get a consistent stream maybe?
@kalebborders2117 4 роки тому
Its moe of like a direct fuel injection system
@tkswdr 4 роки тому
Exactly or about consumption......hahahaha...all the freaking thing is drained...its more nitrous cooled then fueled...
@jacknedry3925 4 роки тому
@@MAGGOT_VOMIT, It refuses to build pressure because the American engine and the German turbo hate each others guts. Shouldn't he supercharge it instead?
@mikecasey3055 4 роки тому
Man that just looks like fun, bunch of work but tons of fun bud. Looking forward for future videos.
@jackgorbachev5753 5 років тому
Im laughing at the people saying this guy doesn't know what hes doing. He can build a Dyno from scratch, put this whole engine together, set all this up, get it working, stay alive, and he doesn't know what he's doing? I think that makes no sense
@mrcaboosevg6089 5 років тому
I could do that, i still don't know what i'm doing
@WarpedPerception 5 років тому
Im a good actor ! LOL
@danielgrampa624 5 років тому
@@mrcaboosevg6089 I have to see it to believe it, can i see a video of you "doing that"? i would be equally impressed. IMO if your incredibly smart, then that intelligence applies to everything you do, not just one thing.
@mrcaboosevg6089 5 років тому
@@danielgrampa624 I would start again if i did it that badly. My dad is a lawnmower mechanic for a living, i used to work for him and i could tear one of these brigs engines down and put it back together with my eyes closed, it'd be the turbo part i'd be in unknown waters with although i have worked on turbos but i've never done the whole thing from scratch. "i know enough to get me into trouble" comes to mind, sure if i had the money i'd be doing shit like this just for fun but i don't. I have a V-Twin 16hp mower engine i have been wanting to boost but forced induction isn't exactly cheap, certainly not when if i break anything i have no means to replace it
@commentnoises5751 5 років тому
I could easily do that ..
@carlover9764 5 років тому
This is very interesting...
@muscleman369 5 років тому
Usually running lean gets you high rpm and power right before it starves the engine of fuel and overheats. Running rich really bogs it down as we are seeing. But props for the determination that was awesome how you kept saying "I'm gonna give it another run" 👍👍👍
@dennischuckiii9710 4 роки тому
I've watched a few of these videos, just noticed you only have 4 fingers on one hand. Keep up the good work, cool videos
@DeltaOps3 5 років тому
Not to be insulting but he has no idea what hes doing does he lol. You dont just spritse fuel at a turbo. You need a fuel management unit of some kind or a fuel regulator that turns boost or vacuum pressure into increased fuel. My suggestion would be get a carb with like the smallest low jet possible, and basically use as little fuel as possible that still makes it barely run. Then fiddle with an FMU that steps up fuel pressure with an adjustable wastegate set to like 3psi. Looks to me my guess is its way too rich, and that turbo isnt getting steady exhaust flow to make boost or you have nothing controlling the wastegate which is what it looked like. Thats why i think i saw bubbling (fuel?) From the wastegate when u took the pipe off.
@butchcassidy5398 5 років тому
I think he had to many fathers hit him in the head for doing things he shouldn't have been doing with there underage children. And meth to....
@allthathpandnotire3019 5 років тому
Liam you don’t know how carburetors work do you. You can’t increase fuel pressure to increase flow in a carb. It’s only using the Venturi to draw the fuel from the float bowl. If you get too high of pressure you’ll end up just pushing past the needle and seat attached to the float. He should really just put the carb before the turbo in a drawthrough setup. Tune the jets from there and be done.
@DeltaOps3 5 років тому
@@allthathpandnotire3019 yeah sorry lol i had fuel injection on the mind which is what most people do. And idk im not 100 percent tuned into what small engine carbs can take, lot of car guys use blow through setups
@DeltaOps3 5 років тому
@@allthathpandnotire3019 i forgot theres no fuelpump
@justachipn3039 5 років тому
Laim... that poor thing was drowning in fuel lmao it was running in low to mid rpm... it's capable of doing better than 4200 RPM... could hit 10hp+ @ 7000k+ lmao... a hit of starter fluid would of been cool lol
@hoganhogan952 5 років тому
The fuel just spraying on the hot exhaust and then the see thru head just sparking away. LOL you made my day dude. Buddy you had gas all over your arm. If that thing popped and made a flame out the exhaust while you were spraying,,,your next vid would be from the burn unit. There was fuel everywhere!
@WarpedPerception 5 років тому
I was hoping and caught fire actually, imagine the whole engine on fire while it's running with the see-through head, all while being filmed in slow motion, that would be epic. If you thought that was bad check out where I was a week ago ukposts.info/have/v-deo/hppeoWqMa2pz22Q.html but I do have all the safety gear there, blast Shields fire extinguishers and all that good stuff. thank you for watching and thanks for your feedback I appreciate it.
@nicholasduma5063 5 років тому
Interesting, keep on, on this experimenting project!
@markgrz7076 5 років тому
Nice to see a UKpostsr that has good slow-mo video quality!
@WarpedPerception 5 років тому
Thank you. And I give other channels credit if they give me an idea, 😁
@jasonneal 5 років тому
I think it would make even more power with one of those 6” Honda mufflers like you see on the back of a civic
@jordancox559 4 роки тому
A pass through can style muffler ?
@raymondwilson9662 4 роки тому
Ya that should double the horse power forget using the turbo
@EATSLEEPDRIVE2002 4 роки тому
*throws engine into a pool of gasoline* “ Dur I wonder why it’s not running right “
@chicagothunder1guesswho868 5 років тому
Start over but next time use a 5hp Briggs engine that they use for Jr. Dragsters. I think it's Horseman products that make all the High-performance stuff for those. The reason the clear head works better is it ups the compression ratio. The stock Briggs rings are weak you get too much blow by. Total seal will make any size rings that you ask them for. The crankcase vent is also holding you back. The Nitro strips the oil off the cyl. walls and the rings will score the cyl. in no time. The rule for Alcohol is twice the jet size of gasoline. Hobby shops sell tiny drill bits and pin vices if that helps. To help stop the head gaskets from blowing out use copper coat on both sides of the gasket let it dry overnight before you install the head then use it to coat both surfaces wet upon installation then wait a few hours before you start the engine. All surfaces must be oil free and use a scotch bright pad to lightly scuff the surfaces by hand.
@eranjones5994 3 роки тому
Dude! Your tha man! I wonder would an over head value would be better, but not taking anything away from the faithful flats!
@MrDouchoid 5 років тому
Really appreciate you putting all this content into one video.
@TheElDavo 5 років тому
pushing all that raw nitro past the rings into the crank case...
@rotary_rsr9794 4 роки тому
i know it a older video but just see it and love it. when you burn nitro it produces nitric acid hence the polishing of the head. hence why the exhaust fumes sting your eyes and nose.
@mobne 5 років тому
This is cool! I just cant wait to see that engine with proper fuel injection. You could need oilpressure to the turbo also!
@johnwessling23 5 років тому
Poor turbo! You need oil pressure feed to turbo!
@GarageSupra 5 років тому
It wouldn't be spinning fast enough or running hot enouggt for this to be an issue. The bearings had a lube they were fine.
@johnwessling23 5 років тому
Rdizz Automotive It would be interesting to see if it would make more boost with pressure fed oil to help the thrust bearing reduce drag.
@phantom240 5 років тому
Or see a tiny ball bearing turbo. That would be the shit for a motor like this running at a relatively low RPM with a small displacement.
@kleetus92 5 років тому
@@GarageSupra Is that why it was puking what looked like silver paint back out of the feed port?! Lol... yeah... totally fine.
@GarageSupra 5 років тому
@@kleetus92 the turbo oil feed wasn't coming from the engine. Watch the video before commenting.
@tjfritts9013 5 років тому
I'm thinking, the see-thru head gave you higher compression than stock head, just because a stock small engine is designed for so-so horsepower for years rather than serious power and questionable longevity.The last run, you got into a rhythm on the spray that seemed really promising. Gotta be away to mist the nitro in, rather than glops of liquid right into the combustion chamber. If it can go in like a mist...that sucker might make 15HP. Great work, sir, and I'm very interested to see where this goes!
@WarpedPerception 5 років тому
Yes I think you're right. That makes perfect sense. Yeah for the next one I got to get through this engine. Only one more episode on this guy. I have others right behind it, next it's going to be electronic fuel injection variable timing, boost control etc, max out the horsepower and blow the connecting rod through the block, then show everybody that anything can be fixed, repair whatever breaks start the engine one last time without making a ton of power and then move on. even if the block cracks into pieces I actually have a solution to fix that not many people know of.
@JamesDownes 5 років тому
@@WarpedPerception 😂 funny and educational, rare hybird
@kennedysingh3916 5 років тому
I can hardly wait to see the result.
@MarkReedman 5 років тому
I left a can of degreaser lying around and my brother mistook it for two stroke fuel. He later said the lawn mower was hard to start and he had to use a can of start you barsted but after it started he was amazed at how much more power it had and how easy it was to mow the lawn that day. Love to see how much you can get out of degreaser.
@fasthackem7853 5 років тому
Hell yeah bro! Been waiting for this. Excellent job. When you were shooting the fuel into the turbo intake, I was literally screaming at my TV telling you to do it after the turbo. I guess you heard me cause then you did it, lol! Next episode is going to be even better! Thank you!!
@WarpedPerception 5 років тому
😁😁😁🤩. Yeah after the turbo makes sense. I wanted to focus on the difference so people can relate to a few different things. Old carbureted cars, first type of turbo draw through systems, and last but not least the most modern fuel injection system, I like to set up those kind of scenarios so people who don't know cars really well can still understand and relate. Thanks I'm glad I finally got this one done, had a really tough 2018 but I'm good now, I'll be bringing a lot of stuff to UKposts this year oh, I'm trying at least once or twice a week.
@JHuffPhoto 5 років тому
Maybe try a little dry shot of nitrous at the turbo. I watch the Cletus McFarland channel and it is hilarious when those guys blow up an engine by doing that.
@loganmessineo2822 5 років тому
How about using a 10hp briggs so it can take to the turbo better?
@minidragbike 5 років тому
No one makes more power than me
@jacobrzeszewski6527 5 років тому
Can’t wait to see the EFI and what the engine is really capable of.
@Shadow-eo2pf 4 роки тому
That flathead is too tough lol, built really good
@roycole4619 4 роки тому
You should try a mikuni carb I have a 26mm on my 5hp briggs it makes around 8.5hp runs mint and it took the top speed of my go kart from 41 to 55mph
@johnhonda93 5 років тому
i was cringing at the "mechanical fuel injection" spraying nitro all over the hot turbo of a running engine.. im honestly surprised it didnt catch on fire. but i think the biggest issue you're having with making boost is because you don't have a pressurized oil system for the turbo. they use journal bearings and if you don't have pressurized oil going through them theres going to be a huge amount of friction in the bearings preventing it from spooling. they don't have ball bearings it's literally a steel shaft that goes through a bronze tube essentially. it needs pressurized oil to be lubricated, just pouring some oil in won't work, even for a short amount of time. you can make an external oiling system with an oil tank and a pump completely separate from the engine, and that would probably make a huge difference on how much the turbo spools.
@WarpedPerception 5 років тому
I was hoping it caught on fire, can you imagine how cool that would have look the engine running with the see-through head while on fire in slow motion!!. I did find out later on that the top mounting hole actually goes through into the compressor housing oh, so it was leaking all of the boost out of that little bolt-hole. If you look back at the episode and look at the part where I'm spraying the nitromethane engine the turbo oh, you can see it coming out of the hole. Next time I'll put a bolt in that hole and I guarantee you it's going to make a lot of boost
@WarpedPerception 5 років тому
@Dave Micolichek exactly, that was the problem, after I saw that in the video I wanted to go back and plug that hole and give it another run, but without the camera set up and running I don't even want to attempt it, with my luck it'll make 10 pounds of boost and blow apart without any cameras rolling..lol. I also found it pretty entertaining how everybody on this video things that I have no idea what I'm doing..lol. I love it . it will definitely need way last nitromethane is that bolt hole is plugged, half of it was coming right back out maybe even more than half, for the next episode I'm going to make that my very first run with the bolt hole plugged. Thanks for the feedback
@VasilyBuilds 5 років тому
Life OD debunked the fact you need a pressurized oil system
@gabrielv.4358 Рік тому
INSANELY AMAZING!!!!! Great stuff!!!!!!!!!
@mechtech9616 4 роки тому
hi it's amazing to see EFI system on this Engine when you make it
@metalrott324 4 роки тому
Omg dude please someone take that spray bottle away from him!!!
@Techmatt167Official 5 років тому
“Let’s start by turning the valve a little” opens it all the way
@abelcerrillo2162 5 років тому
All that freaking work, Changing this an changing that trying this an trying that an the mans clothes still clean. Good job.
@WarpedPerception 5 років тому
I've learned over the years, I've ruining all of my clothes I have kind of adopted to working and still staying sort of clean... Glad you noticed!
@stephenm103 3 роки тому
So cool. Takes me back to my youth before I knew anything and tried stuff like this. . . . .(how long will a 12 vdc motor run on 110 VAC - let's try it and see!)
@jaimenbrunson1652 5 років тому
This engine will work better than my 2.4 Jeep Patriot
@Mike-wc9sz 4 роки тому
Put it in a old manual car.
@jaywilbur515 5 років тому
i musta clicked on the wrong link for the SEE thru engine
@S1yght 5 років тому
The first 5 episodes had a see through head on it but it broke and he wanted a head that could take a beating so he put the original head back on it
@jaywilbur515 5 років тому
Ah thanks man
@beppinococca 4 роки тому
Muy bueno 👍 Greetings from Argentina 🇦🇷
@AngliaNutz 4 роки тому
It's a frickin' miracle that you are still alive
@TheDeathskull37 5 років тому
Try running it with an air compressor and some sort of pressure regulator from a distance.
@TheMadWookiee 5 років тому
Fuel mixture is way to ritch lean it out with a proper carb and it will pull
@TheMadWookiee 4 роки тому
He could run a mikuni and jet it up more that was what I meant not the factory brigs carb spraying in fuel unmetered is drowning that motor
@adamreliford4534 5 років тому
Awesome video. I have vfb to agree too much fuel and hard to manage. But good TV est run . That EFI should definitely do to trick. Look forward to seeing that. You should try try boring the cylinder next put an up graded piston in it next . Good work
@WarpedPerception 5 років тому
Well yeah oh, it seems that way, but in reality I'm going to go deep into the nitromethane air-fuel ratios in the next episode. Nitro runs very very wet.
@matposton87 4 роки тому
Single cylinder turbo engines run best with what's called an air capacitor on the intake side between the turbo and intake valve. The air capacitor size is between 4 and 5 times the size of the engine, so a 100cc engine would need a air capacitor between 400 and 500cc's. You can find plenty of info on Google. I searched "air capacitor for single cylinder turbo engines" and plenty of info including a paper written by the MIT department of mechanical engineering, and there are also several videos on UKposts showing people making air capacitors. Love your videos, keep up the good work
@maximilianth 5 років тому
This guy literally pours tons of fuel into the engine without vaporizing it in any way and wonders why it´s not running very well... Appreciate all the work you put in your videos but this is just not the right way to do it.
@WarpedPerception 5 років тому
Ha!! yeah it was fun I thought it was pretty Kamikaze and very interesting to see if they would actually run and make power just pouring it in there like that. But I mainly did it for 3 reasons, to have fun, to see if it would actually work and make power and boost oh, and to give people who know absolutely nothing about cars a good comparison between this episode where I'm just pouring it or spraying it into the intake system, and the next episode where I use an electronic fuel injection system, a similar structure to what everybody's car uses, this is going to give everybody who is not super knowledgeable about cars and example I've why modern cars use fuel injection and engine management compared to the old carburetor cars or even worse that really really old carbureted cars. That's why I did it. Thanks for the feedback and thanks for the kind words, I'm glad you enjoyed it
@bsod4144 5 років тому
@@WarpedPerception I once poured gunpowder into a 2 stroke weedwhacker engine and the piston kissed the crankshaft..and that on 2 stroke Oo what would happen with a 4 stroke....U HAVE TO DOOO ITTT >3...u could run it on gunpowder if i recall correctly...just make a bowl tip into the carburator with a string
@maximilianth 5 років тому
@@WarpedPerception Thanks for the detailed answer! I´m really looking forward to the next video then! Love your experimental approaches every time!
@WarpedPerception 5 років тому
@@maximilianth thank you !!!
@WarpedPerception 5 років тому
@@bsod4144 ooohhh, that's a great idea, sounds very fun.
@maximhof9489 5 років тому
It'll may generate more boost when the compressor scroll is acting like a belt driven supercharger. I think there is to little exhaust gases to spool up the turbo enough. And also as others said before you run too rich. Try to make a fuel pump with a spray nozzle to atomize the fuel a little jit better so it gets a better mixture with the air.
@bradbohen2615 5 років тому
Dude! What a great experiment!!
@michaeltheriault3708 3 роки тому
I would love to have a set up like that that’s crazy I wish I could make something that’s cool is that you may guys like me want to learn more about engines so for that thank you cause you’re a big inspiration to a lot of people
@Eian_Anderson 5 років тому
18:50 you keep drowning the engine with fuel. Each time you keep stopping, thinking its going to die, but then it comes back to life because it got more air.
@stefan-alinspeteanu9572 5 років тому
Can you place the (spark-)nail in a different spot on the transparent head and compare the flame propagation in slow motion? You could try and add a big pipe in the intake or exhaust (or both) between the turbo and engine, the pipe could store pressure for longer so that when the exhaust pulse reaches the turbo enough time has passed and the compressed air reaches the valve when the engine is in it's intake stroke and can use the extra air. By this logic a bigger pipe would give you more low end torque and a smaller one would give you more top end torque.
@mycosys 5 років тому
That would be REALLY interesting, as would varying the timing once he has the EFI. Do i remember correctly that on a f head you ideally want the spark over near the valves (cos that area cant be compressed so is your main combustion chamber) with timing quite advanced to allow for a long propagation distance to the cylinder?
@stefan-alinspeteanu9572 5 років тому
@@mycosys I would guess that directly over the piston, or slightly towards the valve would be the best and the spark advanced to ~10 degrees, this would allow the mix to burn over the piston and not have the flame front propagate as far as it would when the ignition source is between the valves. I really hope he does this. If i think about it, having the ignition between the valves would help with low end torque while spark over piston should help with high end torque as you can see the flame front still propagating towards the piston even when the piston reaches the half of it's stroke at high RPM.
@mycosys 5 років тому
@@stefan-alinspeteanu9572 on a flathead the area above the piston is squeezed as close as possible to completely flat, at TDC virtually the entire AFM is over the valves. Every flathead ive seen has the spark over the valves, commonly over the exhaust valve . I guess the timing would vary a lot with fuel, i really dont know nitro,ethane
@stefan-alinspeteanu9572 5 років тому
@@mycosys I know that actual car flathead engines have no space above the piston, but his engine does. the see-through head is completely flat and he put metal spacers between it and the block, so the distance from head to piston/block is uniform, that is why i mentioned placing the ignition source above the piston.
@luispereira3 5 років тому
On the see-through head the spark nail must be there as it grounds in the metal between the valves. It is not like a spark plug which has its ground is part of the body and is at the same distance wherever you put it.
@oldsblowyomama1207 5 років тому
YOU ARE DROWNING THAT MOTOR!!!!! The fuel in the oil showed it. Lean out the AFR keep using the after turbo injection. Use a nozzle that will atomize the fuel so it's a well mixed charge. You should have the injection nozzle in the intake tube that's running vertical right before it goes in to the motor and have that nozzle come in at a steep angle so it's in line with the air flow. Keep up the hard work. You put a lot in to make content for us. The slowmo of of the combustion cycle was absolutely beautiful. We all would love to see that puppy make some power!!!
@WarpedPerception 5 років тому
So I started episode 7 a couple days ago, just a spoiler, I show how rich the nitromethane actually has to run just to keep the engine running, but it made almost 5 lb of boost and 8.5 horsepower after I plugged up that mounting hole in the turbo that was leaking all the boost. I'll save the rest for the episode but yeah that was the first scene of the episode. I promise you I actually know what I'm doing, I just act dumb on camera to make it entertaining and well, it's always suspenseful. Thanks I'm glad you liked it
@oldsblowyomama1207 5 років тому
@@WarpedPerception That's awesome! I was wondering what was coming out of there. I thought maybe the wet setup was too much and somehow ruined the seals letting the oil out. I cant wait to see that boost. Have you thought about switching between gas and nitro to see the differences? It might be a little easier to manage vs. The nitro since you dont have to dump so much in and would also be easier to meter. Either way its going be cool to see. I hope you can give the atomized injection a try in one of the upcoming videos too. I think the consistency would help. I'm sorry if the all caps came of condescending but it grabs attention lol. Len
@WarpedPerception 5 років тому
The air fuel ratio for nitromethane is insanely rich, nitro drag cars run so much nitromethane that they are almost hydrolocked. That's the only way nitro methane will run. It's going to be very nice with the fuel injection system because I will be able to show the air fuel ratio vs the pulse width of the fuel injector, that way everybody's going to understand. Thanks for commenting and thanks for watching I'm glad you liked it
@Chris-zp1kd 4 роки тому
To make boost, i recommend to use brake to hold the velocity of the engine and make the intake open to make more power but your not gonna spin the engine more, your just want to bring more exhaust to the turbo to spin to get more air to the engine for more power to have. Its simply call brake boosting.
@picassoimpaler3243 5 років тому
You need the engine under load to spool the turbo. But the main thing isn't the new turbo, it's the gallons of fuel your dumping in lol. In a top fuel car they have boost for days coming from their supercharger, and 2 spark plugs with perfectly atomized fuel before they start dumping that amount of fuel in. If you don't go back to a larger carb or FI system, your never gonna spool that turbo. It's the right size here, compared to the other one, but if you aren't coming close to a stoich ratio with atomized gas, your not gonna be able to make the exhaust to spin it
@WarpedPerception 5 років тому
I completely agree, I wish I could love your comment twice, I set it up this way because not everybody is good with cars, I did it in stages like this so the average person can have a visual understanding of the difference between old carburetors and the electronic fuel injection system that most cars use now. Once you watch this video, and then the next video with the fuel injection oh, it's going to become really obvious why we use the types of systems we use on cars today. For us it's common sense but for average people that don't know much about cars it's a different story
@d46512 5 років тому
@@WarpedPerception Fuel injection became commonplace to keep then-new catalytic converters from fouling. In other words government emissions control.
@msengineeringdavid3702 5 років тому
Picasso Impaler you have no idea what you’re talking about they use 1 plug per cylinder and the reason they use mechanical fuel injection is because of RULES.
@pyroman590 5 років тому
Top fuel dragsters absolutely have 2 plugs per cylinder, as well as two magnetos.
@pyroman590 5 років тому
The stoichiometric ratio for nitro (1.7:1) is a lot lower than gasoline (14.7:1). Meaning you don't need nearly as much air as you do for gasoline. You can burn about nine times more nitro in a cylinder than gasoline. Nitro also needs heat to get going.
@SkypowerwithKarl 4 роки тому
So just how much nitro have you been inhaling? Gotten any headaches? Your heart pounding?
@justanotherboog3497 4 роки тому
I turbocharged a 5hp Briggs in. Auto shop class 20 years ago. I learned a turbocharged one cylinder engine needs a chamber. Or intercooler(not just a open tube ) to supply boost when the turbo isn't making boost for 3 storks if I remember correctly the chamber needs to hold 4x the engines cc.
@sMASHsound 5 років тому
next episode is gonna be lit
@B4Lsoowoop 5 років тому
I'm not trying to freak you out but I think you are missing a finger man
@troyguinn303 5 років тому
@Not Hitler new to the channel... Also curious.
@eamh2002 5 років тому
Ive seen some vids but never actually noticed the finger :D @@troyguinn303
@scrapenbass493 5 років тому
🖕
@B4Lsoowoop 5 років тому
@@scrapenbass493yea I think that's the one
@scrapenbass493 5 років тому
Playing around with his fingers that close to a turbo it's no wonder he's missing one
@WarpedPerception 5 років тому
Seriously People THUMBS DOWN ALREADY !!?? .. geez, so much for blood sweat and tears...LOL
@fabio77809 5 років тому
good good job
@jcims 5 років тому
Probably people shorting nitromethane stock, lol. That's a thirstly little bugger!
@qpSubZeroqp 5 років тому
Regardless, I loved it. Of there was a stronger emotion then just looking, I would
@davyarthurs 5 років тому
They prob didn’t even watch it!
@kapekape7580 5 років тому
Answer do you remember me
@galacticgalaxyonezerone7235 8 місяців тому
It seems like with regular gasoline you can just rev the throttle way up and it runs a lot harder hard to tell sometimes because don’t know if the cam tunes out loud sounds or not.
Слідство.Інфо | Розслідування, репортажі, викриття
Переглядів 1,6 млн
FLIP FLOP Hacks
Переглядів 65 млн
Stupid Fast John
Переглядів 97 тис.
TreshFilms
Переглядів 1,4 млн