I've never encountered a broken bolt stud that could be unscrewed that easily. Usually the studs break because they are stuck so tight that the force required to loosen them is greater than the strength of the bolt.

Стакими ногтями его можно было просто ногтем выковырять)))

Когтями этого мастера можно выкрутить любой болт 🐾🤙🏻🔥

Те,кто сталкивался с подобной проблемой,знают,что этот простой трюк работает крайне редко .

Показан очень сложный случай - обломок свободно люфтит. Вот, если, обломок чуть прихватило коррозией, или на герметике - тогда, вообще, раз плюнуть!)))

Это просто фантастика. Жалко что такие заломыши встречаются в одном случае из ста из за того что это был говноболт. Обычно это прикипевшие, приржавевшие или обломанные из за того что не по резьбе закручивались и вот там всë это не работает. А вот удаление такого заломыша как в видео я бы и снимать постеснялся.

Сверление и сварка уже выглядят проще и доступнее, чем способы на видео.

Application of HELICOIL and punch-walking are two old-school crafts that were taught back in the early part of the industrial revolution. Schools used to teach these principles but technology has all but buried these common since crafts. My dad raised me in a machine shop, so He taught me these principles. I learned about HELICOIL application at my railroad career, and it's SO GOOD to watch it demonstrated on a free-to-watch video to the world! THANK YOU for your video !!!

Болтающийся остаток болта можно было выкрутить выверткой левой и не долбить полчаса. А с такими когтями можно было прям ими как отвёрткой крутить 😂

Если заломыш не прикипел и так свободно болтается, он бы не сломался. Ролик - "сказка"

I generally go with the concept that if it is liquid it cannot be stuck. 🙂 Seriously, anybody who is working with steel bolts in aluminum castings should be applying an anti seize when assembling the parts. It will also help to prevent stripout when tightening the bolts.

I normally use a center punch to: A. Shock the broken bolt, THEN: B. use a left hand drill bit and SLOWLY drill at the center punch mark INTO the broken bolt. MOST of the time, the bit will bind into the broken part and back it out for you. If not, then you can use an extractor in the hole made by left hand drill!. TIP: A bit of grease will catch the shavings and keep them out of the engine.

Loved how he covered the chain with the rag and then blew everything in deeper with the air

Господи я на одном дыхании смотрел эту очень сложную операцию по извлечению сломанного болтика. Хотя мне показалось когда он дул воздухом тот болтик сам уже начал выкручиваться. Одним словом мастер своего дела

This solution is effective only in one case: when the bolt breaks off while being tightened, and when it does not rest against the bottom, after which, usually, the thread “unwinds” and changes pitch if the tightening was carried out without observing the torque. therefore, you first need to make sure that the thread has not “unraveled” on the broken edge. otherwise, when turned out, not only the pitch, but also the alignment will be destroyed on the upper remainder of the thread.

He could have used his finger nails instead of the 2nd hand ground down pliers.

In my forty plus years as a service engineer I would say I have removed maybe 50% of bolts like that but normally they are to tight to knock around, if you have a bolt that is snapped a good way down the hole a good trick is if you have a Lathe get a socket cap screw the same size and thread as the snapped one put it in the Lathe and drill a hole through the centre then put it in the hole were the snapped bolt is then using the same drill bit drill through the snapped bolt it allows you to get the dead centre you can then put penetrating oil down the hole and use an easy out. I always keep a selection of different size bolts ready to use works a treat.

To install a helicoil you have to first oversize the hole , thread and then put in helicoil. for the second bolt only one in a thousand will come out this way. A left hand drill bit will remove some and in the other case a small drill and an easyout will remove the bolt. If not drill out the hole with a slightly larger bit and either tap to larger size or tap and install helicoil.

Здесь смысл не в извлечении "заломыша", а в заголовке ролика. Эффективная замануха - наше ВСЁ!!!

Первый раз вижу автослесаря с таким маникюром 🤪

Парень с длинными ногтями - ты лучший! Такой херни я давно не видел. Ключём ты болт обломал, а кёрнышком так спокойненько, не напрягаясь - тук, тук - и открутил! Молодец!

I'm assuming the bolt broke when tightening because no corrosion is present. Nice presentation on Heli-coil prep and installation. This person is well-experienced on proper tapping procedures of aluminum, backing to break chips and clearing chips before they score the new threads. Nice video!

Маникюр ШИКАРНЫЙ... Где такой делал? Неужто там же, в том же салоне? Я на болтик даже и не смотрел. Да он от чертилки и так бы выкрутился... :)

Тряпочка конечно выполнила свою задачу😂

Came here to learn something, what I learned is how to contain swarf within the engine using a rag and a airline 😵‍💫 top mechanic !

ボルトが折れると焦りますが、中で折れたオルトは簡単に回りますので細い鉄棒に瞬間接着剤を付けてボルトに接着して 接着剤が固まるのを見計らい回転させれば折れたボルトを簡単に取り出すことができます。 硬いようでしたら折れたボルトにドリルで穴を開けて太い針金をこの穴に差し込み瞬間接着剤で固定すればほとんどの折れたボルトを外すことができます。

This is no secret, most seasoned mechanics that I've ever known will always try to remove them with a pick before drilling or welding. I've also sacrificed small screw drivers or flat bladed chisels, grind them to fit the hole and make a screwdriver slot, some time the use of a hand held impact to get them started. Not always successful, but always worth a try.

Thanks for the tip. I'm no longer a mechanic and I used to do the same for hummv cylinder heads. But it doesn't work most of the time. I would use left handed drill bits too.

Great trick that almost never works. Only when the screw is completely free of contamination and corrosion and is not deformed at all. A little galvanic corrosion or rust or oil sludge and it doesn't work. If the bolt is cross threaded it doesn't work. If it is bent it doesn't work. If it breaks in tension, the top few threads are usually deformed and it doesn't work. If the screw is stainless it doesn't work. If a steel screw is threaded into aluminum, it doesn't work. I could go on. If you have actually tried this trick, then you have probably resorted to drilling and using an ez-out or welding a stud, or drilling and re-threading to a larger size, or drilling and heli-coiling, which is what you see him doing on the first of the two holes. Probably because the simple trick didn't work and he resorted to using a drill and drill guide to remove the bulk of the bolt, then a dental pick to try to pick out the remaining pieces, then ran a tap into the hole, found out that the thread was shot anyway, then bored it over, tapped it, and put a heli-coil it. Note that you can see the stub of the broken screw in the first hole before he starts tapping, then there is a cut at 1:47, and turns the tap back out and the screw piece is gone. These UKposts tricks and "Next level process" videos always make anyone who has actually worked in a machine shop or repair shop roll their eyes back in their head. When you see "life hack." "next level," or "simple trick" in a youtube video, it should set off your bullsh!t detector.

You are right to try this first, call it plan A. When this fails, go to plan B which is drilling and EZ outing. Plan C is welding a stub on and/or apply heat.

Many years ago I had a stud break just below the surface of an alloy engine block. The guy who saved my bacon took a short length of mild steel flat bar, drilled a hole near one end, slightly smaller than the stud diameter. He then TIG welded the bar to the broken stud through the hole. He then just unscrewed it, the heat of the weld also helped free up the corrosion which caused the breakage in the first place. My broke stud was held completely tight... the method shown here would never have worked.

Hello, Thank you for the video. It was very informative concerning one method of removing a broken bolt and in this case in an aluminum casting. Using a punch to screw a set of threads on out the way they were going. I used to be a machinist in a Ford road truck dealership and removing broken bolts was part of my purpose and I did remove hundreds of them. I just want to bring up a couple of points. Point 1: It is seldom you get a broken bolt that will come out like you have just shown in this video. Most of the time, the reason the bolts are broken is because the threads are stuck in the threads the bolt is put into. Removing any broken bolt, I used to always try to use the method you have demonstrated first as it is the easiest. When I have tried what you have shown and the threads are stuck where they will not screw out, I try taping strait down on the broken bolt to see if that will break the threads free. If not, I will put some heat on the broken bolt and going forward, there are more invasive ways to do that will come next. Point 2: In the video, you attempted to surround the place where you were working with a cloth to keep from getting savings down in the head which will ultimately get into the crank case. You did good putting the rag around where you were working. But, the next thing you did was take an air line to clear the trips away where you could see. Well when you used the forced air, you just blew all those shavings and chips right up under the rag. Not Good.

Проще простого, попробуйте таким способом извлечь прикипевший остаток болта или закрученный не по резьбе)А тут можно было и когтями)))

Thank you for this idea, very helpful to save money

I have done this before too! Thanks for the great video, and a huge thanks for not ruining it with crappy background music.

I've used the same trick myself. I used a masonry nail as a punch with it being very thin, sharp and very hard. Take your time and care don't mash the hole or the end of the broken off bolt up.

My good friend, I can assure you that if that bolt had heat seized in that casing, no amount of tapping it with a punch would get it to loosen up. I also love the way you use your circlip plyers to remove the bolt, what happened to your long nosed plyers?

Thank you I just broke one of the bolts off the magnita on my pushmower working on the flywheel. My homeboy let me take the bolts off and the first one I took off I broke it LOL

Походу шпильку обломали на закручивании и с упором носика в тело головки, не в край резьбы, иначе обломок так легко бы не выкрутился

Вот это по нашему. Закрыть (местами) тряпочкой и ...Раздуть( а не пропылесосить) всю стружку по всей "башке" (гбц). Лайк за солидарность в технологиях "срача". (Шутка , хотя...)

You could use a drill bit that runs counterclockwise to drill a center hole in the broken bolt. If the bolt is loose enought the drill would back out the bolt.

Вся стружка в движке. Молодец косяк.

Этот мастер-фломастер когти стрежет когда-нибудь?

I encountered this very same thing on my 1979 morini 350 when a hardened trunion (rocker shaft) stud snapped flush with the head. My dad who was a marine engineer taught me this exact same method using a small sharpened punch and it worked!!

I have had numerous old cars with rusty water pump bolts that like to break off and those reverse cutting drill bit will usually get them out especially if they arent stuck to bad and then I use stainless bolts when I assemble and use anti siege compound and they always do good

A lot of you don't seem to understand this was just to show you the technique, not what he probably would have done normally. It was just a demonstration, created for whomever might benefit. Now you know....

Развеселил! Молодчина! Кометы, огонь!!!

Мне больше всего понравилось выкручивание болта пальцем! Ну и, конечно, надо было в двигло ещё пару щепоток стружки и какого-нибудь мусора насыпать. Для надёжности!

You placed a cloth around the broken stud to stop swarf going into the engine and then proceeded to blow the swarf into the engine with the air line!😅

Backwards turn drill bit will often spin those right out. The punch method I've used often as well.

Nice job all the shavings inside the valves 👍

Как же он этот болт обломал, если он так легко идёт? А главный секрет, как выкрутить болт - это ногти не стричь. Никогда. 😳

TIP Sometimes there is a small screw like a No 8 or No 10 stuck in a hole. Its head has broken off. For that I used a No 6 self tapping screw and drive it into the broken screw. A moment later the hole is free and new threads have been tapped.

I see this video was just over eight minutes long. Good job tho . But if you have never tried left hand drill bits you will be greatly surprised by trying them. This would have took less time to do than it took to put the bit in the drill . But you did great your way also . Thanks

Simplest way is not to break the bolt in the first place. If it feels tight, apply a little heat to the bolt head only. Cool with air line and repeat as many times as necessary. It usually works after the first couple of applications.

Left handed drill bit is always my first option. Has worked more times than I would have expected.

Способ конечно не очень,но ноготь вообще огонь 🔥🔥🔥

да ты просто чертов гений!!!как я жил до этого ,засверливая обломок и пользуясь левым метчиком,чтобы его выкрутить?все -зря...но теперь то я знаю,как надо и легко выверну все обломки,не напрягаясь со сверлением..почему я не знал этого раньше?

Some people add a little bit of bearing grease in the shred collecting portion of the re-threading tool. This way it lubricates the cut and collects the material keeping it in that gap rather than it slipping between or rubbing into the threads.

Um parafuso quebra por excesso de força no aperto. Este está completamente solto. Quando quebra e trava, o melhor ( se possível) é furar o centro com uma broca fina, ir alargando o furo com outras brocas e por fim usar um macho de rosca esquerda.

The first one might happen once or twice in a life time.the second one I've done 3or4 times in my life,works when your lucky enough that the stud is loose in the thread.

Yeps, blow lots of swarf into the top of the cylinder with compressed air. Great technique.

Обычно прикипевшие или ржавые болты ломаются,посмотрел бы я как он их выкрутил этим сомнительным способом.

Nice to see he blew the swarf all around the valves and rockers, should have taken more precautions.

You are creativity It's true I am a new subscriber to your channel and this is my first comment in this video that deserves all the appreciation I wish you success and lasting success, God willing and his blessings Your friend Hani from Egypt from Cairo

Depende donde este El birlo capado Si es uno que esta en el múltiple de escape O si esta cerca de paso de agua que se haya oxidado Par esos son diferentes formas

Очень познавательное видео, от души посмеялся, а ещё больше от комментариев 🤣🤣🤣

Когда он начал выкручивать обломок круглогубцами, я подумал это оператор ему решил помочь своей рукой😂

One of the best ways to remove a broken stud is with a left hand drill bit. More often than not the drill bit grabs the stud and backs it right out. I have to do this almost every day taking stainless screws/bolts out of either aluminum or stainless holes and sometimes cast iron.

he's a badass. very nice job

Мастер крут .Так могут только парни с такими ногтями.

The best way is to take out the whole piece and drill the broken bits with smaller drill bit on a perfectly horizontal surface. The way it is done here, there may be problems later when fasterning back the machine as the screw trade has been damaged. The method show here not in line with precision engineering.

0 out of 10 for good engineering practice. Nicely blowing all filings everywhere so that they can find their way into oil galleries etc. Brilliantly done.

Именно что трюк🤓прикипевшие и пережатые обломки такими ногтями не испугать. 1 как на видео - легкими постукиваниями керна 2 высверливаем, вкручиваем вывертышь. 3 привариваем гайку, заодно ослабляем зажим при нагреве 4 левым сверлом или переделанным обычным. 5 два отверстия и отверткой с пропилом или подобием ключа от болгарки 6 3х гранный напильник в заранее просверленное отверстие 7 специальным электродом, образующим на сломаной шпильке стержень Пс. Думаю, надежнее было высверлить, заварить аргоном и нарезать новую резьбу, а не ставить какую то х...

Надо же, а баба просто супер. Мужик бы ни за что не догадался😂

Paciência e Capacidade! Parabéns! Aprendo mais um! Valeu! 👍

All ready use 15 years ago.thank you. I am a machine shop.

A truly skilled craftsman at work👍

Уникальнейший способ! Просто Шедевр в сфере технического решения.

Очень интересно.Сверху закрыли тряпкой,чтобы струшка не попадала на на детали при нарезки резьбы.Но стружка то падает вниз.Ребята-будьте внимательны,особенно,когда продуваете сжатым воздухом остатки стружки.Рекомендую вам,просмотреть ваше видио самим,как это всё вы делали.

These days, a High Speed Dremel is your best friend, if you do not have Easy-Outs. Diamond Bits for the Dremel will easily cut a straight Screwdriver Slot into the top of the broken stud (or bolt), and then heat-up the aluminium casing. An Impact Screwdriver can be placed, and a few quick hits may free the broken stud. WD 40 would also be a benefit. OK to use this method providing the broken Stud or Bolt isn't too deep, and this is just another way to get success.

Это не проще, чем засверлить сломанный болт обратной резьбой или парой отверстий для ключа по типу вилки.

Обломок *болта* - далеко не то же, что обломок *шпильки:* в торце первого можно просверлить 2 отверстия под плоскую отвёртку с вырезом - а в торце второго придётся сверлить *осевое* отверстие для экстрактора (негодного метчика со спиленными на косой клин зубьями).

В бытность работы мотористом частенько отламывал болты (особенно у зил-120?) на головке блока , но ни разу при отломе, отверстия там не было, чтобы нарезать резьбу. И приходилось сверлить, потом забивать что-то твёрдое и выкручивать Ну или же иметь сверло, может метчик левосторонние.

I found that using a left hand drill works best to remove a broken bolt.

Kalau membuka baut yg patah dengan cara tersebut itu adalah cara jaman dulu sebelum ada alat draad putaran terbalik. Sampai sekarang masih ada yang pakai cara tersebut.

Попробуй постучи кернышком по обломку шпильки в выпускном коллекторе двигателя, или по обломку свечи в свечном колодце. Экстракторы разного диаметра не дураки придумали!))

Poczekam z rok jak mi urosną takie pazury to też tak będę czarował!

посмеялся от души. если резьба слабая и болт вкручен не до конца без натяга и не прикипел тогда да. но выкручивать надо не керном а заточенным эксцентриком маленьким зубильцем . если не идет сверлим по центру меньшим сверлом забиваем заточенный из твердого металла конус . с другой стороны конус заточен под ключ и выкручиваем не нарушая резьбу

@ 4:43 May I know the name of that conical tool? Thank you for the great film of a very skilled master.

A small drill and a round tapered file i used a lot before left hand drills were available. For bigger bolts i used a round tapered steel rasp after drilling a hole in them.

Для таких обломышей и по сложней очень помогают свёрла с левым вращение.

als het ding zo los zit kun je even goed goed wat sillicone lijm of zo erop zetten of klein beetje epoxy en er iets op vast kleven om zo uit te draaien dat gepruts met die tap slaat nergens op..

Так сломаные болты не выкручивают, резьба повреждается! Надо не лениться и делать все правильно. Работа ответственная. Лучше засверлиться, аккуратно забить шестигранник - звездочку и выкрутить.

O truque, afinal, não é tão simples como parece, caso o parafuso esteja bem firme dentro da rosca. E geralmente parafusos quebram justamente por estarem presos na rosca. A melhor maneira é usar um punção e marcar o centro do parafuso e depois ir furando com um broca fina (de widea, melhor) e enfim usar um extrator se necessário, já que às vezes dando reverso na furadeira (bem devagar) a broca "engancha" no parafusos e este sai numa boa.

Вот это трюк, сума сойти!😏

для выкручивания надо иметь целый список приспособлений, инструментов.. а так все просто - делать нечего...

Pretty lucky it was quite loose. Another thing you can do tapping for your hele-coil is put grease on the tap to grab chips.

Я чуть не заплевал увидев ногти

Что бы стружка при нарезании резьбы не сыпалась куда попало, и не выдувать ее потом компрессором, надо мечик смазать густой смазкой типа литол.