instructions were 10 times better than most adults ive seen making these
@TiagoTiagoTДень тому
Not sure if tech has change sufficiently over the years, but my past experience with small brushed motors and quads is they're disposabled; if you get the same luck I've had, it won't take too many flights for yo to need to replace the motors...
@jkdoodle4460День тому
i have one but the app is no longer available 😭😭
@jkdoodle4460День тому
is there any way to still use this
@TheeRedditRatДень тому
Please bro what studies did u follow
@aminatakinade3055День тому
Price
@TheeRedditRatДень тому
Whats his job
@MaxImaginationДень тому
This is my job.
@TheeRedditRatДень тому
No but for real Im looking for the name I would like to do something like this @@MaxImagination
@BizzareClipДень тому
where is the code
@tanojimoДень тому
I like how he made this with easy to find tools
@earthlingi72День тому
what a GREAT guide ! awesome work ... loved it
@GreatHacker1День тому
I'm tryna synchronize the sketch with the MultiWiiConf but it simply shut down. I'm using the arduino nano. Do you have any idea why I can't connect to calibrate?
@DhruvPatel-jo9tnДень тому
Just curious, why didn't this drone use any encoders with the motors. Was this compensated for by the IMU and in software?
@MaxImaginationДень тому
This is all handled in the software. Keep in mind, it's not a brushless drone to have encoders.
@luansalja602 дні тому
Great !!! thanks a lot, you made a huge work, is the device can work without sd card ? i mean only for streaming not to save file into it... sorry for my rusty english..
@MaxImaginationДень тому
Hi there! With how the code is configured nowadays, you NEED the SD card in order for it to work.
@TheGripsion2 дні тому
This project is so sick dude!
@MaxImaginationДень тому
Thanks, Alex!
@nekuseek2 дні тому
Beautifull job on making this video i m interested in building it but i dont know how the camera system works like are there alternatives for gogles or better camera ?
@MaxImaginationДень тому
Thank you! There aren't many alternatives of this size, it's just about as good as it gets unless you're willing to invest much more $$$
@jeffrenko2 дні тому
Hello i made my tx and rx but when I connect a servo the servo turns and stops but I can't control with tx I check wiring
@MaxImaginationДень тому
What type of servo are you using? Have you checked the outputs with your multimeter on the receiving end? I think your TX and RX aren't connected, actually. Make sure you're using a 10uf capacitor across the power terminals of each NRF module to resolve connection issues - or use a more stable 3.3V supply for them.
@user-rg9rd5cb7u2 дні тому
okay, very impressive, but now rebuild everything for esp32-cam
@MaxImaginationДень тому
Thanks! The ESP32-cam is not compatible with this project.
@user-rg9rd5cb7uДень тому
@@MaxImagination I am kidding you with this rude words. I really like it, and some time ago was really curious about using arduino as a flight controller but had no idea how to replace motor speed controllers, but now its all clear to me, and I'm going to build it. I'll try to stream video on my smartphone and transmit controll signals from my smartphone as well, so the whole project would be a bit cheaper
@Abdullahadam6452 дні тому
I dont know how to get all these small things or how long is the car ?
@MaxImaginationДень тому
I don't understand your question? The dimensions are shown on the blueprints.
@shubhs.20852 дні тому
your videos are bringing life to my childhood engineering dreams! i used to open any electronics i could get my hands on and try to replicate it to understand about thier workings, and i litereally used to buuild retro custom version of my electronic toys and RC cars!
@MaxImaginationДень тому
That's awesome! Glad to hear that!
@braaitongs2 дні тому
Your programming circuit is wrong. it didn't work for me. In your video you used the GND next to the 5V pin, but in the diagram you use the one on the opposite side.
@MaxImaginationДень тому
It is actually correct... Maybe your FTDI board is different from mine?
@RedCrystal3062 дні тому
can i use this code for esp32 devkit v1? please help me!
@MaxImaginationДень тому
Yes, you should be able to. The code is inter-compatible with different ESPs.
@RedCrystal306День тому
@@MaxImagination Oh, thank you for your help. However, I tried uploading the code to my microcontroller yesterday, and it didn't report any errors. But after being reflashed, the microcontroller cannot broadcast WiFi even though I tried restarting the circuit. I'm really stuck. I hope you can help me this time. Thank you so much.
@raghuvm27912 дні тому
great work! brother!!💫
@MaxImaginationДень тому
Thank you! Cheers!
@tedbastwock38102 дні тому
This video deserves a ton, sh*t ton of views. Like you I recently read an EE forum where a bunch of EEs (or wannabees, idk) were saying that what you just showed us is impossible. Great job, and thanks for sharing. New sub.
@MaxImaginationДень тому
I highly appreciate that! As my mantra goes, "You can make anything you set your mind to".
@playr25622 дні тому
Dude how is your scissor cutting the pvc so easily. Mine takes forever to even cut an inch of the parts. Plz give me solution to this problem
@MaxImaginationДень тому
Find sharper scissors or sharpen them. Also, you may want to heat the plastic more.
@jackmortem45572 дні тому
We gotta add that nickle based nuclear battery to this.
@excalibruh13802 дні тому
call it the fairy fly
@GAME_PRO_PERSON2 дні тому
Nice project ❤
@MaxImaginationДень тому
Thank you! Cheers!
@Animeaindia3 дні тому
Brother I have a dead phone but all its components are working like display battery camera etc. Only its motherboard is dead so can I make something for it please tell me.
@MaxImaginationДень тому
You can probably make something from using its battery, vibrator motor, and speakers. Combines with a number of other parts, you may be able to make something, but not so much.
@AnimeaindiaДень тому
@@MaxImagination can we connect raspberry Pi or another item to use as motherboard etc
@thecongo85053 дні тому
What would be the total cost of the equipment to do this?
@MaxImagination3 дні тому
$180-250 USD including goggles and the transmitter.
@ElTioMichel3 дні тому
The final work is amazing.
@MaxImagination3 дні тому
I appreciate that!
@saharitaeun10483 дні тому
omg that worked
@tessaschumacher59963 дні тому
I would make a tiny car for my baby Brother
@smkn13bandung-r.farhanrizk513 дні тому
I'm still confused, what is the use of AC voltage in this circuit? on the schematic
@MaxImagination3 дні тому
That's only if you choose to use a relay to divert AC power. Change out the relay for a transistor for smaller currents and DC voltage.
@charlesballiet70743 дні тому
now to get it to carry 3 grams of plastic Xplosive
@H4x_Editz9003 дні тому
Hey max I didn't understand the connection between l289 with receiver
@MaxImagination3 дні тому
Hey! Maybe this can help: ozeki.hu/p_2999-how-to-setup-a-dc-motor-on-arduino-nano.html
@H4x_Editz9003 дні тому
@@MaxImagination thanks it helped me a lot
@akshaygs2923 дні тому
I really want to build this, but there is too much variables and fine tuning, is there a pcb for this?
@MaxImagination3 дні тому
Hey! No, there currently isn't.
@larisaefremenko-zenec54123 дні тому
It's a great idea but I can use acro for fly ?
@MaxImagination3 дні тому
Thank you. Its default mode is acro, from my tests.