75 amps of current later he has crappy AC.

Un hombre virtuoso 🎉🎉🎉

Todo un ecosistema planetario y luego que si la abuela fuma

nice job !

With that battery pack a range of 1 mile. lol

try chain or double chain

na bro better buy a real car for 500$

Finding car insurance may be difficult.

nice !

Put a big resistor With a potentiometer On it On your map and maf sensors and you'll get them in the proper parameters.

4000 w / 12 volts equals 333.3 amps. An arc welder is 75 amps. What are you using for wire to hook up the unit copper pipe? These units are measured in gallons per minute or liters per minute not wattage. I have them on UKposts my videos 12 years old. If you run them using a pulse width modulator it will increase the hydrogen between 20 and 40%.

This was discovered when they charge batteries hydrogen comes off them that's why they tell you not to smoke when you're charging a battery. How does this person ever think that he made 4,000 watts? Its measured in liters per minute not wattage. Ohm's law is watts / Amps x Volts or Volts / amps x resistance. All other calculations can be made from those two formulas. @ 12vdc it would take 333.3 amps to make 4000 w.

Сказка! Нельзя через штатный впрыск,это осуществить! Давление необходимого нету! Колличества газа нехватит! Для тупиц и ограничено мыслящих,этот бред зайдет!

cool build, however efficency of a peltier-system is around 5% so you need humongous power to get any useful coolingpowerout of it..

Peltier is a very inefficient for the purpose, it has high current draws and for the car it will tax tax the alternator heavily let alone the electric battery powered car, you will be better off with butane gas air coolers instead

Great great great 👌👍👍👍desribes detaily . how if without any chemical like KOH ? and add blower to reduce hot on plate...

how much in total? cause its about $65 a set and im not going to watch but would like to hear back from you when i watch it later.

You may want to use a gas compressor that only works when the car is moving? it surely will be more energy efficient. I loved that little electric car. LOL.

TEC1-12706 (12v 6A) 24x 12v 6A (72w) TECs Thats 1'728w on layout 3s 4p So that is then 36v 24A (864w) per XT60 So need 36v 48A or 72v 24A power supply But your running it on 12v and have relays to switch 2s from/to 2p mode ? Basically running it at 1/3 power or 1/6 power ? If I understood it correctly 🤔 So sacrifice power to efficiency If I remember correctly at full power those modules are like 5% efficient at full power But what is the efficiency at 1/3 or 1/6 power?

I feel what he has in all that he could have just got a new ac installed in the car lol

if this is true and not fake then why r v importing feul of billions dollers.

Galing! Push mo pa. Gaano ba kalaki batterya mo? Ilan milage nya? Ganda ng idea mo....

Totoo talaga yang hydrogen fuel kaso ang problema ang bilis nya sumabog kaya pag kinabit mu sa makina pati lagayan ng tubig sabog

and whata do you do to filter the nitrogen oxide produced during the hydrogen combustion?

Finely one really word test ride Good work continue like that

Cool that he built it but sounds like a power wheel

I love that it sounds like a giant power wheels

hoax

this sounds exactly like one of those cars that little kids can sit in and drive

Only one plate welded to the axle two inches wide.....FAIL😮

So ad a separate alternator? Room to make the amps. Where does this equals on price to drive. And what will happen to the battery. Still efficient. I will still say yes

You need work the correct amount of water. When the acid level is at its peak. No more gas is made. Dont ask way. I dont know. You need keep a clean but very small amount of water running in the tank. Hope it helps mick Australia 🇦🇺

saw it, liked it :D awesome job ... welding is one helluva potential to create pretty much everything... if just know what to do :D

It's just 6.66 Paisa per liter of gas wow amazing

😢😢😢😢😢

😂😂😂😂

Nwow po ba yan?

Im going to make one just to fill a balloon with it and set off on the 4th of July. Lol Big Boom.

That would make a good model for an NEV at around 25 mph. A larger battery pack would get respectable mileage since the motor is pulling about 2000 watts.

Adiós contingencias y no circular😮 entre semana y sábados

Awesome

min 07:49 Ouch...!!! my foot JAJAJA🤣😂🤣

Já da pra ir na casa da namorada sem pegae busão. 😅

What you should of done was construct electrical leads on each corner. That way you would reduced the electrical resistance of corrosion resistance metal plates. This would increase efficiency and reduce the heat in the HHO generator Sir. Hope you keep that in mind when you build another unit of want to upgrade what you made by modifying just a few plates. Also, you need to tweak the car system electronics to take advantage of the OxyHydrogen gas. JOB well done DIYer. v

the 2 plates in the middle are not even touching anything. It doesn't work without those extra powder ingridients?

so what happen? what you going to do?

😂😂😂de la bouine quand même

range 200m

With a rigid assembly, the battery and transformer could make a good rear cargo rack, especially with a few bungee tie down loops.

Great ! But how long can the Peltier effect module work without damage?