flash positive charged water over a negatively charged aluminum wire. when they meet, they should create 100% hho with aluminium oxide as a byproduct, which can be heated back into aluminium.
@user-jp2em5hy5fМісяць тому
If the HHO is fed into the intake BEFORE the airflow meter; the flow meter is metering out fuel for a gas mixture that already contains fuel (H2). Feed your HHO into the system AFTER the airflow meter just for a start. There are other changed engine parameters that need to be tuned for too.
@kentevans4218Місяць тому
Correct.....same with oxygen sensors. Put spacers/extension between exhaust pipe and ox sensor.
@shaneoneill225420 днів тому
Why
@shaneoneill225420 днів тому
What kind of spacers. For length
@rexford90192 місяці тому
Voltage should be around 1.7 VDC per cell, target amperage should be .25 amps per square inch per cell. Use cross hatch pattern. HHO implodes during ignition. Water fog injection is needed to emulate slower burning fuel such as gasoline.
@SKAD_692 місяці тому
2Н2О >>>2 Н2 +О2 !!!!!!! 😅😅😅😅😅😅😅ННО 😅😅😅😅😅😅😅😅😅😅😅😅
@godwinsboomМісяць тому
2H2O =HHO + HHO
@quantumenergysolutions912810 днів тому
Incorrect! The reason the graphite cell was shedding was because he used way to many volts with the Urea electrolyte. It only needs 0.3v per neuteral cell! He could have had 18 cells with only 5.5V.
@messiaslavorperrone2948Місяць тому
I spent 3 years doing all kinds of experiments with hho, I even used Peltier tablets to cool the water, the Idea to know the consumption and use the scanner to know the injection time.
@amirgedon16 днів тому
i think u should step down dc fuel pump and injector from 12v to 8-9v. My opinion.give me your update..
@caseiriks7169Місяць тому
Did you add an efie, ? Otherwise the ecu detects more o2 and starts to compensate adding more fuel. I disconnected the fuel system and add a SU carby, the ecu only controls the spark and timing. I run a very lean fuel mix and add 180 watts of hho at 15 amps giving me 10 liter per 100 on a 3 liter pajero that used to do 15 liters per 100ks.
@sridharboyana9250Місяць тому
I liked your experiment. I am planning to build one for my bike {350 cc carburetor bike}. I understand that graphite has a smaller lifespan to SS304. So I made my plates with 316L which is more anti- corrosion. I was thinking in the same lines as not to overload the alternator and considering a separate power supply. I intend to publish the results on my channel when I get to where you are presently. I was also thinking to install a wind and solar generator to charge the additional battery on my bike. One factor which I would like to consider is de-carbonization of the engine(while using HHO) over a time period which may result in better efficiency. Instead of HHO. What performance one can get of ICE if it pure hydrogen? This is my unanswered question so far. All said and done I respect you for the time and energy to make the video and sharing. Thank you. Bless you
@Siriusinfo14 днів тому
😊
@unikzacontrutora2 місяці тому
Tests should be conducted on vehicles with 5th generation GNV systems. As they already have more advanced equipment that allows changes in the systems and can better accept HHO. As an admirer of the HHO system here in Brazil, I am interested in learning more about its applications and benefits.
@esahg54212 місяці тому
put a positive wire onto a tap with water, so that when the water drops out it carries a positive charge. then put your negative terminal onto some aluminium wire (like used for welding) when the positive water meets the negative aluminium, they should flash into 100% HHO, the byproduct will be aluminium oxide, which you can reuse again by smelting it back into aluminium.
@EustaquioNunes2 місяці тому
Eu também tenho muito interesse nesse sistema, desejo troca de informações. I am also very interested in this system, I want to exchange information.
@pcpatel012 місяці тому
Had received a few suggestions. Hope it helps 1. Use a powerful flashback arrestors- preferably 2 one near the hho kit after the bubbler and 2nd near the air in-take. 2. HHO input after the MAF(Mass air flow) sensor and not before. p.s. these are just some suggestion that - do it on your own risk
@albertnario48772 місяці тому
yes, thanks 👍
@shaunhall68342 місяці тому
Hello from Colorado. Excellent work!
@albertnario48772 місяці тому
thanks sir
@Woffy.Місяць тому
If you look at the short term fuel trim through the OBD 2 you should see a drop as the ECU changes the injector pulse width, this way you can keep the ECU in the system and avoid a lean burn condition which is not good at high RPM. Also to mitigate intake explosion by fitting a flap valve after the Throttle body to release excess pressure from the intake plenum. I had Lexus LS400 V8 on LPG / Oxygas. Good effort.
@technokid414Місяць тому
Can you tell me more about your lexus LP setup? I want to do the same to my vq25 engine.
@Matt-wb7lm2 місяці тому
Very ingenious, your on your way to something positive.
@johncollins19692 місяці тому
My gosh you are very clever. Thanks for the video.
@gearscodeandfire2 місяці тому
Great build video. I am working on something very similar. Is there anyway for you to estimate how much gasoline was needed to replace the charge on the battery?
@albertnario48772 місяці тому
i can't compute it when it comes from the engine.. i don't have intentions to charge it from the alternator, instead it is solar or grid. it makes it cheaper that way
@Timothyis2 місяці тому
Looks wonderful - Canada
@DaVeHiLl200Місяць тому
🤫 Perforated metal sheet has a larger surface area, also if your gas can't get away from anode/cathode fast enough you're generation efficiency goes down as you're using less or the available surface area. The water heats up because stainless steel is very resistive, platinum is the perfect material to use but it's too damn expensive. Low voltage, high amps is apparently the way to go or high voltage low amps pulsed at quite low frequency to keep temperatures down. I wonder how well 240v at 50hz rectified would perform? With graphite plates the problem is that it's very sacrificial, no good as you seen, not for anode anyhow. We need to use an anode that can't be used for electroplating yet is very conductive and does not erode or corrode. If you think of a cost effective material that fits requirements please let me know 😊👍
@MiloBeni51692 місяці тому
Este video nos anima a seguir haciendo lo que la mayoria de las empresas se niegan a reconocer. Felicitaciones por el video, seguramente seguiras desarrollamdo este sistema, y estaria bueno injectarlo directamente. Habra que reprogramar la computadora y agregar un compresor a diafragma para que sea capaz de generar 3,5 bares. Asi se puede usar el injector del auto y evitar explosiones.
@user-jm7wl5bj3w2 місяці тому
Молодец , возьму на заметку .
@slimel-gharbi81702 місяці тому
do you plan to carry out the experiment with HHO?? If you have the possibility I suggest you also test the separator system and share your thoughts with us Thank you so much
@slimel-gharbi81702 місяці тому
планируете ли вы провести эксперимент с HHO?? Если у вас есть возможность, я предлагаю вам также протестировать систему сепаратора и поделиться с нами своими мыслями. Большое спасибо (Я не знаю, возможен ли автоматический перевод!!!)
@user-jm7wl5bj3w2 місяці тому
Я сейчас очень далеко от дома по работе, по приезду домой хочу поэксперементировать@@slimel-gharbi8170
@mrsunyofficial5 днів тому
amazing tips
@eugenesitsМісяць тому
take a look at the amps, if You put an additional batteries for HHO this could give You something. But in general You will have a hybrid car, petrol-electrical.
@slimel-gharbi81702 місяці тому
Great, very informative experience except that oxy hydrogen (HHO) is dangerously explosive if the detonation is too strong!!! it is better to complete the assembly with a separation system to obtain the hydrogen AND the oxygen each on their own
@albertnario48772 місяці тому
yes it's very explosive ,bubbler tank is very important.. oxyhydrogen is already good in the engine ..
@CoincidenceTheoristМісяць тому
Stop trying to scare people. Why are you here? Hmmm
@slimel-gharbi8170Місяць тому
@@CoincidenceTheorist Try to scare people!!! No, but am I dreaming or what? I'm just informing these people of a scientific truth that everyone should know It's YOU who SHOULD normally warn them and you don't do it, you mislead them!!! and it’s serious! Try doing this experiment on a small scale to convince them: Don't forget that I am here because I choose to be
@DaVeHiLl200Місяць тому
There's always one health and safety bot hiding, waiting for their opportunity to chat poo 🤣🤣
@DaVeHiLl200Місяць тому
If you want to separate hydrogen and oxygen you can do it with a powerful magnet or electromagnetic as they are opposite magnetic polarity... That's what I came to say but the health and safety guru distracted my attention 🤣🤣👍
@briangattrell2195Місяць тому
2.6 volts is more efficient you need to add neutral plates to divide into cells to get to 2.6v from 12v.
@kentevans4218Місяць тому
Legit test.....good job!! You need to put an extension piece between your oxygen sensor and the pipe. That way the oxygen sensor won't tell the computer to make the fuel mixture more rich. Heat i@the challenge on these HHO generators. Maybe try less electrolight.
@AngelRodriguez-mb2vv3 дні тому
Tal vez no era para más potencia pero si para más peso eso k le puse en un auto iría haciendo maravillas x la carretera
@newageautotechnologyМісяць тому
Nice job
@vincentcliongМісяць тому
Have you try using 4x LiFePo4 battery to replace accu in gasoline car. It saves fuel more than 10% and no maintenance needed.
@mr.RICHCH2 місяці тому
Bravo🎉
@Atimar01Місяць тому
for max efficiency try to get the voltage per cell down a lot. for example experiment with H2SO4 (battery acid ... yes ...) with this, the cell voltage goes down to about 1.3V per cell. also use verry thin plates since a thicker plate heats up more due to electrical resistance. now you'd think battery acid is too dangerous right? well, so is KoH, its just on the other side of the PH neutral.... also, you only need verry little of it, basically you set the max amps with the amount of acid. you can obviously use extra acid, but than you have to set max amps with the controller. also, like @rexford9019 said, limit amps to 0.25A per sqr inch. means larger plates ;) --> better efficiency
@philjoyce79392 місяці тому
Urea and potassium hydroxide? So how do you dispose of the chemical mix that remains after electrolysis to exhaustion of the hydrogen?
@kevinlsims7330Місяць тому
Clean Your Drains With It?
@str8up59819 днів тому
I worked with this a few years back but the nay-sayers got to me. Keep up the work. How is the fuel economy now?
@johnslugger2 місяці тому
*_To make a real difference you need at least 200 to 300 amps! I do like your 4 plate BI-POLAR CELL However!!! That's smart!!!!!!!!!!!!_*
@fishingwithhusnainmani50302 місяці тому
Sir plate ka size or thickness please
@ianbottom7396Місяць тому
Despite your efforts I doubt that your reduction in petrol consumption is greater than the cost of the energy input for the HHO
@idontknowmyfirstname692 місяці тому
Did you have any problems with your electrolysis cell getting hot? It appears to be a lot of current for the volume of the cell
@albertnario48772 місяці тому
it's getting hot without the PWM.
@jozefsetlik7050Місяць тому
After just a few minutes, such a cell boils and the insulation that needs to be used is PTFE. another disadvantage is that stainless steel plates corrode and the electrolyte turns into green soup. For many years I have had contact with devices from OWELD, which produces such devices intended as gas welding machines. a better solution for a car is an oxygen cylinder with a volume of 5 liters and a tube leading to the air intake. The engine has a great kick. You have to be careful not to overheat the pistons.
@a3electronics1572 місяці тому
can you test it on diesel engine thanks nice content
@luisacevedo35702 місяці тому
interesante demostración empírica, habrá una forma de aprovechar solo el hidrogeno? es decir tocar solo el gas que sale de los cátodos? Saludos desde Chile interesting empirical demonstration, will there be a way to use only hydrogen? That is, touch only the gas that comes out of the cathodes? Greetings from Chile
@davis4921Місяць тому
How much electricity is required from battery to generate hydrogen from this generator?
@davey2k12Місяць тому
You know there's a nasty chemical left over when the stainless breaks down what you using in the water
@mickgatz214Місяць тому
Who was watching the angle grinder disc slowly get worn away?... 😂
@ikifkifМісяць тому
what are the middle layers og graphite doing if there not connected?
@davidrobertson198017 днів тому
Yeah the graphite experiment is quite interesting, I wondered why they're not connected too in such a small build.... I actually used a neutral plate every 3 stainless plates in my builds.
@escalibur55572 дні тому
Realiza las pruebas en un lugar más silencioso, parece que tuvieses un aeropuerto al lado.
@siov42792 місяці тому
as you state the pressure gets too high over 850. Although you have the setup for better containment already. that case for one! you just need to get some metal containers of somekind for the other parts that hold the electrolite?
@siov42792 місяці тому
then youill t need to worry about going up in flames!
@MohamedAshraf-oo5wdМісяць тому
How do you control volts and Amps onto this HHO system??? 👍
@torrielandsman4625Місяць тому
the current is controlled by how much electrolyte you put into the mix, more electrolyte = more current. as the solution warms up it becomes more conductive and can run away on you. one way to help controlling heat is by useing six cells in series just like a car battery.
@marcnavarro629717 днів тому
No only hydrogen generator, but oxygen too...
@monamo4Місяць тому
hello , is your channel open for sponsorship ?
@jacaliriooracionyfe.37022 місяці тому
Las dos placas de grafito del centro que función cumplen?las veo aisladas de las de los lados y sólo trabajan las de afuera.
@josegante69824 дні тому
es correcto. estan aisladas. funcionan como divisores de tension..
@joemason91872 місяці тому
Possibly an EFFI filter to basically lie to the ecu about the air/fuel mix, and definitely PWM you will improve fuel efficiency with EFFI ice vid old bean
@antoniosestar36712 місяці тому
How can the ecu detect thought o2 sensor the additional oxygen, when the reaction of hydrogen and oxygen form water?
@joemason91872 місяці тому
Well I'm just saying what I had to do for the transit, had to put an EFFI filter attached through back of the obd port, trouble was that before I put that on I thought I was getting better fuel consumption, in a way I was but at cost of more fuel input but that ceases when you add EFFI plus van is quieter faster on the uptake
@siov42792 місяці тому
I Just though of something really interesting! What if you installed that potentiometer on the gas pedal somehow so that when you press it down the voltage will increase so you can possably get even better milge so the Oxyhydrogen is more abundant when accelorating? would be even better if there was some sort of storage tank and pressure gauge with some regulators etc. is this something that could make tis even better? or too much?
@kevinlsims7330Місяць тому
Explosive!! There Is A Reason This Is Not Replacing Fossil Fuels!
@sridharboyana9250Місяць тому
hydrogen production by increasing voltage (not preferred) but current is. the impact of increasing current takes a few seconds to produce more Hydrogen, may not align with throttle response, just thinking not done it yet to tell you for sue
@antoniosestar36712 місяці тому
Did you notice any power gains from HHO?
@albertnario48772 місяці тому
i didn't notice any improvement on the engine power, maybe on carb type engine, you may notice the difference..
@flappingflight85372 місяці тому
@@albertnario4877thanks for your honesty! Since you are putting some additional load ( via the alternator) on your engine in order to produce the HHO on board, even neutral power or/and fuel economy “gain” means , that HHO is helping at least a little bit with improvement of combustion .
@albertnario48772 місяці тому
@@flappingflight8537 no, I don't use alternator to provide power on HHO, I use different battery for it.
@albertoramonacosta12122 місяці тому
Que es carbono hierro fundido
@user-hs1on8gl6x2 місяці тому
the big problem of that design is HEAT and low conversion of liquid into gas. i suggest that you study or find the right resonance frequency of water; ;if you found it you can now easily separate the hydrogen and oxygen very fast with 12volt and 3amp power supply only without additives'..and your reactor metal mush be like in a catalytic converter. hope this will help to your experiment
@Endless_science_2 місяці тому
What is this material? And how can we use this hydrogen to start a motorcycle?
@SKAD_692 місяці тому
ЦЕ ЧИСТА НЕРЖАВІЮЧА СТАЛЬ!!!!👍👍👍
@Endless_science_2 місяці тому
@@SKAD_69 What??????
@user-wh2fx6pf4n2 місяці тому
You can’t you would need another engine it can’t run on his car either he’s fooling people
@haslanchehassan60242 місяці тому
Tenaga taidak boleh dicipta Pak.
@luisalfonsoarteagacorredor783426 днів тому
Deseo q nos traduzca este súper video
@user-pt9vg7kv8n2 місяці тому
I want one, let me know how much.
@luisalfonsoarteagacorredor783426 днів тому
En dónde encontramos la tarjeta y resto de cosas??
@marcoantoniomanes50732 місяці тому
I´m from Brasil. Make a video with a diesel pickup.
@albertnario48772 місяці тому
I don't have a diesel car..
@marcoantoniomanes50732 місяці тому
@@albertnario4877 would it be possible to use H2 +O2 , in diesel motors whithout causing overloads ?
@albertnario48772 місяці тому
they say it will work..
@vincentcliongМісяць тому
Jika 3 liter per menit dan pakai susunan plat paling efisien yaitu -nnnnn+nnnnn- di jarak antar play 0,5-0,8 milimeter itu pun perlu setidaknya 600 watt sebab di kondisi paling efisien pun cuma 0,1 liter per menit gas HHO tiap 20 watt. Jika 3 liter per menit accu dan alternator tidak akan cukup untuk memberi supply daya. Kalau andaikata kurang efisien perlu 850 watt maka hasil gas dengan susunan plat seperti di video mustahil 3 liter per menit, separuh sudah bagus sekali. Perlu accu yg di charge. Maka bukan mobil ternaga bensin saja tetapi, mobil tenaga bensin + accu. Pengujian jangka pendek bagus cuma apa menguntungkan jika dipakai jangka panjang?
@mickgibson370Місяць тому
It take electricity to make the hydrogen! And if you are burning in your car take 2 times much and 1/2 the power!
@ernestlageman15534 дні тому
The 304 stainless steel wil after a short stop to creator gas . The water turn in to red. Whe have stopp whit our projects in car
@pen25Місяць тому
Lol. This is just too funny.
@albertoramonacosta12122 місяці тому
Impresionante lo que produce en 4,2km no podra mucha producciin otros dicen que debe producir 100litro por minuto para ser eficiente en un coche cual sera la verdad Arg
@elarcadenoah90002 місяці тому
link from graphite plates and prize ?
@albertnario48772 місяці тому
s.lazada.com.ph/s.jh18z
@elarcadenoah90002 місяці тому
@@albertnario4877 ok thanks
@raufshahid423217 днів тому
Temperature high ho ga
@clintonlau58262 місяці тому
Your plate sanding wasn't done right , that is done in a cross stich pattern by sanding diag top corner to bottom corner of the plate then do again corner top accross to bottom corner like an X pattern getting everything fully sanded both sides it makes a huge differance. Also port it in were the vacum on the brake master clinder connects faster delivery . Good Job well done
@Rick1234567SМісяць тому
Use it to make a steam engine you will get millions of views.
@cindys18194 дні тому
All this is cool, but in real world terms: how much percent fuel ecomony gain can I expect? What are theveffects on Hp and torque and...ENGINE LIFE?And is there anyone making a really SAFE And Honestly EFFECTIVE HHO Generator Kit?
@rhiantaylor34462 місяці тому
So the energy to split water into HHO comes from the alternator which typically runs at
@albertnario48772 місяці тому
The battery for the HHO is separated from the engine.. it has its own energy provider.. it is cheaper to charge the battery than to use fuel.. sorry for the poor explanation on that.
@iriobrixcbrixner77262 місяці тому
Nós deficientes precisamos explicações faladas e não só visuais gostaria que fosse explicado através de fala
@triblax2 місяці тому
Center plates are useless
@albertnario48772 місяці тому
you can call it neutral plates, it's important to have it to maximize HHO generator efficiency.
I wonder if your car computer was able to compensate for the leaner exhaust by increasing the fuel being injected. That may be why you didn't see much improvement using the lower hho flow rate. The higher flow rate may have been too much for the computer to compensate for. Fooling the O2 sensor may result in better economy with hho.
@antoniosestar36712 місяці тому
why would be mixture become lean? The additional oxygen from HHO form water when burned
@albertnario48772 місяці тому
maybe it's better to use it on an older engine. on my first video about HHO, 1.2L/min oxyhydrogen can increase rpm by 200 in the carburetor type engine..
@flappingflight85372 місяці тому
@@albertnario4877on the older carbureted engine most probably there is no idle RPM stabilisation/ regulation system that is why idle RPM increase .Since HHO must increase the rate of burning of the mixture, it’s equivalent ( as a result) of increasing the ignition timing advance angle ( the idle RPM are stabilised by varying the timing advance angle in most of the modern EFI engines ) . The fact that the idle RPM increases with 200RPM , means that HHO is doing something positive for the combustion process. The energy balance ( energy spent on its production / increasing energy efficiency production from the engine ) is another story .
@cosh7670Місяць тому
ماهي الفكرة من هذا
@aleksandarpetrovic66132 місяці тому
You are skilled man. 850W is too much for alternator, not just for the HHO generator. Try with much less watts, 50 to 300, just need a time to see is there some results (minimum 150km, up to 2000km).
@albertnario48772 місяці тому
hho generator has its own battery, it doesn't take from the engine...
@aleksandarpetrovic66132 місяці тому
@@albertnario4877 ok
@jamiejoker118Місяць тому
Ino one side produces o2 the other side H2 qestion we only want H2 so isn't there anything we can do with the input voltage to just produce H2 ino it's DC 1.7 25A square 25mm but could we just excite H2 NOT the o2 all that power amps is wasted say 25A ÷ 2 12.5A get the gas we need half the input power we are exciting 2 element's to get 1 I might be way of here lol.
@LuisAlbertoBentancur20 днів тому
Lo que nadie dice que la batería calienta los cables, además la rompe en muy poco tiempo hasta que no inventen un buen distribuidor de la corriente, no es muy viable en una palabra, es un ENGAÑO
@jaimeosoriora2 місяці тому
The problem is more Oxigen (from this cell) then oxigen sensor send more fuel. Please remove Oxigen from HHO. Make only a HH cell.
@antoniosestar36712 місяці тому
Doesn't the extra oxygen from HHO becomes water with hydrogen when burn inside the engine?
@linctexpilot83372 місяці тому
The extra oxygen enhances combustion…… More complete combustion does not put more oxygen into the exhaust emissions
@gregooify2 місяці тому
🤯
@ManuelValdesRojas-nn6lmМісяць тому
Remove fuel. Only use hho.
@davidrobertson198018 днів тому
Sadly the car's computer will compensate for the extra "oxygen - it thinks" going into the system and will add more FUEL negating the addition of HHO to the economy. The timing needs to be retarded for a more complete burn also, hydrogen burns infinitely faster than petroleum and if you watch videos on how ICE's work you'll see the plug sparks before top dead centre to make up for the slow burn rate of the fuel. SO imagine all the hydrogen igniting before the piston has reached TDC, it's fighting against itself (the engine) to finish it's travel before starting it's down stroke reducing the power and demanding more FUEL from the petrol tank by the "untrained" computer. Try changing the resistance on the oxygen sensor wherever it is on your car to trick the computer into a very lean running state. This is much better done on OLDER cars and their primitive carburetor driven engines, but can also work on diesel engines quite well. Get a 4 stroke mower running on pure HHO and you'll discover tweaking things faster. I AM a mechanic AND an electronics technician BTW and OLD lol. Frequency is the key here, once you discover the frequency the plates produce gases best then you're getting further. Think diodes and capacitors as a frequency "energy tank" with cascading connections to tweak the input. BTW I have NEVER used chemicals in the water, it's not so good for the environment although pure HHO running motors actually CLEAN the air as the run it through their system. Keep trying friend, it's possible - ask the dead Stanley Meyers!
@abpccpba2 години тому
Hope you have not degraded you Toyota Car Systems and warranty. STOP Unknowingly you may be doing long term damage. Like emission requirements at your next DOT registration; new tags.
@maciejpilarski35812 місяці тому
It isn't hydrogen generator, but Brown's Gas!!! be precise, please!!!
@sridharboyana9250Місяць тому
he never mentioned h2 alone all the way he said oxy hydrogen. Watch it before you comment
@maciejpilarski3581Місяць тому
Pecise during writing title for movies, ,cause title describing whole thing!!@@sridharboyana9250
@mukhitdinruziev91202 місяці тому
This is all bullshit!Don't fool the people by taking away their time!
@user-wh2fx6pf4n2 місяці тому
Exactly fake misleading liar he is
@SmartfibonachiМісяць тому
Неправильно сделал электролищер и не правильно запитал его,поясню,есть определенная площадь которая эффективно позволяет делать электролиз при условии оптимальных параметров,нагрев к количеству и еще циркуляции,у него же все 3 параметра не правильно при подключении видно как электролит уходит чего быть не должно как и дыма это как раз не правильная работа электролизера,если уже решил делать то можно изучить для начала вопрос.еще и напряжение на ячейку 1.2-1-8в максимум.ну а для легкой повторимости можно выполнить из спирали одна в другую высота 5см расстояние и длину опытным путем
@user-wh2fx6pf4n2 місяці тому
Hydrogen would not run the engine in that car why are there so many misleading people on you tube and other sites these days
@anthonyg46712 місяці тому
He didn’t, he used it in addition to the fuel for increased mileage.
@user-wh2fx6pf4n2 місяці тому
@@anthonyg4671 lol 😂 this guy
@anthonyg46712 місяці тому
@@user-wh2fx6pf4n I know It can, I have used one myself ,stopped using it only because it buggered the valve seats . So not a good idea unless the engine is prepared too.
@user-wh2fx6pf4n2 місяці тому
@@anthonyg4671 hence my first comment you need a different engine as I’ve said 👍
@anthonyg46712 місяці тому
@@user-wh2fx6pf4n I should have read your comment properly 🥴
@thra5herxb12sМісяць тому
🤣🤣🤣🤣🤣🤣
@mdrafiqul33582 місяці тому
@NixUgriBugri21 день тому
Great another sorceri video ... the only problem that physics doesn't agree ... by the way where the hell the energy is coming from to "generate" the hydrogen ... ? So you convert all the energy back somehow what required to generate the hydrogen .. right ? The engine is at best 34% efficient so just by burning the hydrogen loose energy .. Another total nonsense....
@albertnario487720 днів тому
it has its own battery.
@NixUgriBugri20 днів тому
@@albertnario4877 and the battery charged by WHAT ? you don't get it right ? this is a scam you are "scamming" yourself...
@brendan96982 місяці тому
Stop wrecking your engine. This introduces water to the engine, after running for a while check your oil. If it turns milky stop.
@SKAD_692 місяці тому
хто скурив в туалеті підручник фізики , тому усе здається шкідливе або фантастичне !!! 😮😮😮😮😊😊😊😊😊
@user-wh2fx6pf4n2 місяці тому
@@SKAD_69this dude is misleading people for views he a liar not a truther
@romsaymwiti9387Місяць тому
It evaporates into steam
@joedee186323 дні тому
Good test spoiled by poor video techniques. Too many faults to mention
@iriobrixcbrixner77262 місяці тому
Eu dei um deslike neste vídeo porque eu sou deficiente visual e não entendi o que se trata este vídeo muito desaprovado
@McGyver008Місяць тому
What a SILLY NONSENSE!!!
@vincentcliongМісяць тому
Cara membuat drycell yg efisien ukposts.info/have/v-deo/iWGUrnyocHukl4U.htmlsi=eITcJGjN2itlZzdu