How to cut and thread steel conduit - Apprentice electrician essentials
Переглядів 13,016
День томуThreading steel conduit is one of the most common requirements when installing a metal conduit based electrical installation. In this video, we look at how to thread a 20 or 25mm galvanised conduit with a set of manual stock and die set.
( If you are watching from outside the UK you may find our metal conduit very different to the EMT system and other light gauge conduit used in the USA etc - but please add your comments)
======================
🕐 TIME STAMPS 🕕
======================
00:00 Threading steel conduit
00:54 Building the stocks and die
01:30 The die is handed
01:55 Length of conduit
02:39 Conduit vice
03:05 Rules about hacksaw blades
04:02 Conduit angle
04:54 Square end..?
05:07 File the end
05:41 Going in dry
06:18 Jake uses lube
07:19 Two threads hanging out the back
07:44 Reaming the conduit
08:12 Coupler
09:02 Four way spouted box
09:36 Two threads showing
================================
🔦 More conduit videos from eFIXX
👉www.efixx.co.uk/metal-conduit
👉www.efixx.co.uk/how-to-bend-co...
👉www.efixx.co.uk/conduit-instal...
==AD=====================================
Series produced in association with
Metpro - Conduit and accessories
👉 hub.efixx.co.uk/metpro
Bend-it-now - Conduit Bender
👉 hub.efixx.co.uk/bend-it-now
=========================================
📍SUBSCRIBE TO THE CHANNEL eFIXX helps electricians, electrical contractors, building services engineers, and electrical apprentices. So if you've been on the tools for years or just starting your electrical journey, we'll help you stay up to date with the latest regulations and developments in the electrical industry. 👉hub.efixx.co.uk/youtube-subscribe
========================================
⚡️ Take a deep dive into the latest electrical products, applications and technology
👉 hub.efixx.co.uk/essentials
=========================================
🚧 More resources for electrical apprentices and learners
👉 hub.efixx.co.uk/apprentice
=========================================
#efixx #conduit #electrical
@andysims4906 2 роки тому
I was always taught you put the cutting compound on with your finger ,how times have changed.. My stocks and conduit bender are at least 60 years old and probably more .i wonder how long these shinny new ones would last on site. Very good video by the way ,thanks for posting
@stevemullen3666 4 місяці тому
Great video, well explained.
@grahamturner6119 2 роки тому
I was using screwed tube in 1963 threw all my stuff away last year didn't bother in 63 with cutting compound in those days everyone used cheapo lard just as good
@shiamjad Рік тому
Best Series ever
@acespark1 2 роки тому
Excellent work there, although you might want to use the pipe grips in the other direction or even get a set of 9 inch Footprint pipe grips 🔧
@raychambers3646 2 роки тому
I used to put two threads on ,then do the filing then thread compound, this prevents clogging files up with compound and filings ,apart from using grips the wrong way nice vid as usual.
@ojogbenga9114 Рік тому
Excellent! Thanks for sharing your wealth of knowledge. I'm wondering if you could share "How to construct a conduit wiring system from scratch. This should show the 1st, 2nd & 3rd fix. Many thanks again.
@muhimmiah8640 Рік тому
Legend
@davey6024 2 роки тому
Whoever made that little blue stock and die kit first should be charging royalties to everyone else who makes it now. I'm sure it's the only type you can buy in the world cos its the only one iv ever seen over 20 years of doing this 🤣
@johnswallow1550 2 роки тому
Can I ask why you wold prefer a high speed steel hacksaw blade to Bi-metal. Also I thought you should be sawing as close to the vice as possible. Keep up the good work.
@sergiofernandez3725 2 роки тому
High speed steel hacksaw blade to Bi-metal blade preference could certainly be explained better.
@thoughtful_criticiser 2 роки тому
Cutting close to the vice stops movement caused by vibrations when cutting such thin walled pipes.
@cj-rb8fz 2 роки тому
Didn’t give the stocks and dies a bang on the side of the bender to clear them out , didn’t wipe inside conduit and used grips wrong way round 🤦🏼♂️🤦🏼♂️😂😂😂
@ja_adam_ 2 роки тому
There is no wrong way round to use grips.. it works the same
@cj-rb8fz 2 роки тому
@@ja_adam_ there’s a correct way ,🤦🏼♂️the moveable lever goes at the bottom that way the more you squeeze the levers together the tighter it gets as you turn the grips
@ja_adam_ 2 роки тому
@@cj-rb8fz it did the job the exact same ? The coupler wasn’t loose? What advantage would it have given in that exact situation?
@cj-rb8fz 2 роки тому
@@ja_adam_ to call your self a tutor and not know how to use a pair of slip grips
@ja_adam_ 2 роки тому
@@cj-rb8fz thanks for not answering my question
@muhimmiah8640 Рік тому
Ive got a shorty/stock n dies/but no conduit no compound no ts nor squares no reamer no files n never done conduit work. But i uve given me the impetus to try...im 1 month into my 2346..22% in. Got my 18th n 2391-52 staring next week... The am2 has got to b the defacto bench mark for a sparks and thats what aiming towards with the help of ur vids...f@ck me...ive sussed out the wiring centre...ur legends
@billyaird2912 3 місяці тому
The threads should be 16mm which is 2 threads showing as the dyes are ar13-14 mm and talo I find is the best not the new greases & compounds
@KingZongo 3 місяці тому
Can you tell me why it should be 16 mm ?
@elijahwaggoner545 2 роки тому
When would you ever want to hand thread rigid when cordless pony threader are readily available
@efixx 2 роки тому
When your starting out it’s best to learn the basics
@elijahwaggoner545 2 роки тому
@@efixx I get it you want to learn the basic way of doing things but this is a little bit past the point of inefficient even for fresh hands
eFIXX
Переглядів 30 тис.
GSH Electrical
Переглядів 10 тис.
Polly Pie
Переглядів 143 тис.
Notebook1 Ассоциация сервисных центров
Переглядів 60 тис.