The Secret to a Perfect 90-Degree Conduit Bend

День тому

In the final part of our metal conduit series, we show you how to produce a ninety-degree bend exactly in the middle of a one-metre length of steel conduit.
======================
🕐 TIME STAMPS 🕕
======================
00:00 Bend in the middle
00:44 Measure and find the middle
01:12 50 mm form the middle
01:45 Mark on the former pin
02:15 Creep
02:31 Don't you just love a Tipp-Ex mark
02:45 Is it square
03:31 Measure
03:54 Impressive pair
================================
🔦 More conduit videos from eFIXX
👉www.efixx.co.uk/metal-conduit
👉www.efixx.co.uk/how-to-bend-co...
👉www.efixx.co.uk/conduit-instal...
==AD=====================================
Series produced in association with
Metpro - Conduit and accessories
👉 hub.efixx.co.uk/metpro
Bend-it-now - Conduit Bender
👉 hub.efixx.co.uk/bend-it-now
=========================================
📍SUBSCRIBE TO THE CHANNEL eFIXX helps electricians, electrical contractors, building services engineers, and electrical apprentices. So if you've been on the tools for years or just starting your electrical journey, we'll help you stay up to date with the latest regulations and developments in the electrical industry. 👉hub.efixx.co.uk/youtube-subscribe
========================================
⚡️ Take a deep dive into the latest electrical products, applications and technology
👉 hub.efixx.co.uk/essentials
=========================================
🚧 More resources for electrical apprentices and learners
👉 hub.efixx.co.uk/apprentice
=========================================
#efixx #conduit #electrical

КОМЕНТАРІ: 19

@helmanfrow Рік тому

Seems to me that the manufacturers could inscribe angle markings on their conduit benders and make everyone's life easier.

@peterconnolly4608 Рік тому

Don't forget the wear and tear over time ,have to be alert all the time ,

@neonblizzard8110 Рік тому

Enjoyed this whole series of videos and has made me much more confident doing metal conduit - and i haven't been an apprentice for a very long time!

@efixx Рік тому

Thanks for the support

@GSHElectrical Рік тому

Nice work Jake

@linksone6287 Рік тому

Great video as always gents. Time to put some plastic conduit bending content out there! Cheers

@efixx Рік тому

Point taken

@lukejay Рік тому

I love the tipex. do you have a video showing how to add it? Thanks.

@MrUtube1916 Рік тому

Do you have a link for the resource where it tells you the bending radius of the conduit? I think it would be useful information to know how much stretch you would get out of each size of pipe for differnet degrees of bends. Cheers for the video Gaz!

@ahmedibrahim-yc8pe 2 місяці тому

Thank you for this lovely video ... Is the rule of 2.5 x 20mm is applicable on any conduit diameter (eg 2.5 x 25mm)?

@bhavneshpatel3687 Рік тому

Hi i am.doing nvq 3 experience route . And i will doing am2e soon need to.practoce to get bend right forst time . Is there any special course available in near by college only for conduit bending? If so please let me know

@timh5529 Рік тому

Any chance you guys could do a video for a handle bar set?

@efixx Рік тому

- check out the playlist - we call it a bubble set

@timh5529 Рік тому

@@efixx Sorry. I should have been more clear. When I say handlebar set I mean a 4 point set or bridge set. Not a saddle set or bubble set.

@arputharajr7842 2 роки тому

How to make bridge bending on metal conduit pipe

@efixx 2 роки тому

Conduit Bubble Set ukposts.info/have/v-deo/sqKcjptwoaOTqmQ.html

@AdamS-lh2ug Рік тому

Is this how it’s always done in the UK? We don’t use conduit bending “machines,” we use hand benders and you either bend off the ground, or in the air, the only difference is wether the shoe or the handle is on the ground, and some find bending off the show on the ground is easier. This changes when you get 1.5” and above, as it’s just way too difficult for an average person to make those bends. So you either use pre-manufactured 30’s, 45’s, or 90’s with couplings (most common). Or you buy a hydraulic or whatnot bender. Company I used to work for had 80 commercial electricians in the field. That expensive thing was at the Upornor plant at all times (it was like an 8 million dollar a year industrial contract, they got all the nice stuff).

@alanmarriott9216 Рік тому

Couldn’t you somehow find a way to mark the former with tip ex or marker where back of bend is and thus eliminate the need for scrap tube and set square?

@SME_Ste Рік тому

Yes you can. You only need to position the conduit using the scrap and square the once, then once in position you can measure back onto the former, lets say 100mm, then mark the former. The next bend you do, all you need to do is measure back 100mm from your back of bend mark and line this up with the mark on the former. Works everytime