METAL CONDUIT BENDING - Longer length bends - Apprentice electrician essentials
Переглядів 18,428
День томуIt's easy when you know-how - Here's a tip for bending longer lengths of steel conduit.
Jake and his helper Gary run through metal conduit bending techniques as a continuation of our conduit installation series.
======================
🕐 TIME STAMPS 🕕
======================
00:00 How to bend conduit over 1 metre in length
00:51 One metre mark
01:20 The only way is up
01:46 Scrap piece of conduit and a set square
02:16 Keep the pressure on
02:40 Is it 90 Jake
03:20 Overbent
03:37 Foot on the conduit technique
03:55 Pulling out overbent conduit
04:30 Under bent conduit
05:01 Adding more bend by hand
05:43 Is it 1 metre
================================
🔦 More conduit videos from eFIXX
👉www.efixx.co.uk/metal-conduit
👉www.efixx.co.uk/how-to-bend-co...
👉www.efixx.co.uk/conduit-instal...
==AD=====================================
Series produced in association with
Metpro - Conduit and accessories
👉 hub.efixx.co.uk/metpro
Bend-it-now - Conduit Bender
👉 hub.efixx.co.uk/bend-it-now
=========================================
📍SUBSCRIBE TO THE CHANNEL eFIXX helps electricians, electrical contractors, building services engineers, and electrical apprentices. So if you've been on the tools for years or just starting your electrical journey, we'll help you stay up to date with the latest regulations and developments in the electrical industry.
👉hub.efixx.co.uk/youtube-subscribe
========================================
⚡️ Take a deep dive into the latest electrical products, applications and technology
👉 hub.efixx.co.uk/essentials
=========================================
🚧 More resources for electrical apprentices and learners
👉 hub.efixx.co.uk/apprentice
=========================================
#efixx #conduit #electrical
@MrMrm324 2 роки тому
Honestly I haven't come across a better UKposts channel than this one. You just learn soo much. Efixx team you are the best! Thank you for all your hard work.
@efixx 2 роки тому
👍
@ja_adam_ 2 роки тому
😁😁😁👍🏼👍🏼
@BlRaidX 2 роки тому
My respect went out the window when they started reading from brochures about next gen tech products. Without putting sponsored on the video YET it was clearly a sponsorship endorsement for largest developer in UK to upsell their houses and look they got social media PR around it. Shame not a single sod explained anything beyond how it looks fancy. Even basics like the temp control being sections not by degrees. That is something anyone with common sense would of burst laughing at. Not a single part of video contained a single downside which clearly indicates they was paid to promote.
@darkdepth1991 2 роки тому
You are Damn Right!
@mostafa-zx4sk 3 місяці тому
Very nice and easy without complicated measurements very nice work
@rmmj7james293 2 роки тому
Ah never knew about reversing it. Thanks Lads
@avfczoff Рік тому
Fantastic lads. Always appreciate your videos. So helpful & extremely well thought through & explained. You’re an excellent teacher Gaz
@Dog-whisperer7494 2 роки тому
Nice job well done that man . Christ that boy is good 👍 Fantastic video guy’s as always 👍👍👍👍❤️
@ja_adam_ 2 роки тому
😁😁😁❤️
@benmanning5789 3 місяці тому
Bend it upwards ffs I was wondering how it was done, didn't think of that brilliant thanks
@TheBigstve 2 роки тому
Brilliant fantastic guys
@sugardaddyxxx 2 роки тому
Nice 👍🏽
@timpat29 Рік тому
Hi lads can you go through the initial set up of the bending machine for both 20mm and 25mm formers. Which holes to use for the bending arm etc. Thanks.
@00beasis Рік тому
Do you have any tips and tricks for putting bends in pvc conduit with a bending spring at exact measurements?? I’d love to have a method to do 1 or 2 bends in a single piece
@alanmarriott9216 8 місяців тому
Is there not a way to insert the conduit into the bender from the back and bend the smaller part down? Think it adds or takes away some distance though. Hoping someone can clear this up as seen people on site doing it but don’t know exactly what it puts on or takes off. Any help please???
@essdee9143 2 роки тому
When you're on site you don't have time to faff around.. The fastest way to get a perfect 90 degree bend is to make your bend with the bender then using a magnetic sprit level stand on the pipe as in the video and adjust using the level.. 😉
@SteS 2 роки тому
You could always use something like a Trend Digital Level. Stick it in before the bend and check the degrees as you bend.
@essdee9143 2 роки тому
@@SteS That would work if the pipe in the bender (after the retainer hook) was parallel to the floor, but unfortunately they aren't made that way..
@SteS 2 роки тому
@@essdee9143 if the level was reset to zero before bending I'm pretty sure it would work.
@zippymo672 2 роки тому
@@essdee9143 I don't understand why they don't design a bending machine with degrees etched onto the former so to make things easier.
@dvrn86 7 місяців тому
@@zippymo672 they benders with the degrees on the arm
@raychambers3646 2 роки тому
Are you going to do a tutorial on wiring lighting in singles ,say a two way switch at each end with lights in the middle?
@johnkash8282 2 роки тому
You should just hire someone
@elsdonsparks 2 роки тому
I was told on my first day, "Never Bend Down on Site.".
@essdee9143 2 роки тому
Hahaha...!
@raychambers3646 2 роки тому
Try this with 25mm ,it gives you a good workout.
@ja_adam_ 2 роки тому
Upcoming video dealing with that .. gaz gets a workout 🏋️♀️
@jamesbrook-fox9396 Рік тому
I'm confused. The measured 1m length wouldn't be the part that should scrape the floor. Is this technique to help where the excess after the measured point (ie sticking out towards you) is longer than a meter....
@dvrn86 7 місяців тому
Or use the mark back method!
@alanmarriott9216 Рік тому
Nice video but in reality a lot of the time a 3m length is what you use. Any video on how to bend 300mm in a 3m length please
@ladcjd1 2 роки тому
Your benders roller is still in the 25mm former size hole this will flatten out the tube.
@cj-rb8fz 2 роки тому
You’ll get snide comments from them if you point out any wrong doing
@MrUtube1916 2 роки тому
Which hole are you supposed to put the roller in for bending 20mm conduit and which are you supposed to put it in for bending 25mm? I had to put a missing roller in the bending handle the other day for bending 25mm conduit and I didnt know which hole to put it in so I put it in the 2nd hole above the former. It was very tight but it seemed to work. Was this right or wrong?
@robertwilliamson3934 2 роки тому
Yep just as I would have done it lol
@danielhearnden3776 9 місяців тому
Ahaaa what if your in a 900mm tall room 😂
ВПИСКА
Переглядів 4,5 млн
GSH Electrical
Переглядів 52 тис.
GSH Electrical
Переглядів 190 тис.
KOMPUKTER
Переглядів 111 тис.