Shovelhead ➜ bit.ly/3Yp71w4 Pre-Order Sale, $100 OFF Coupon Code : SH100 Only $499.99

Yep.... That's just like a shovel head..... Had a few.... That's awesome.

Wow the sound is excellent!

Front cylinder is beyond rich. Didn't know if you noticed the puffs of black smoke it kept making. Would most likely idle better and smooth out once the exhaust is on and the carb is adjusted. Pretty darn cool though!

Pretty bloody, nice n shiny too. Cool piece to have on display 😎Very reasonable on the price too 👍

Wicked Stevo, love it. Never heard of these guys but it looks....and sounds perfect 👍😂

Nice! been waiting for the shovel!

It's not a temp sensor, it's a hall effect sensor so the CDI knows where top dead centre is so it can fire the plug at I would assume around 8* btdc and then advance as rpm rises

Love the sound of it. I know it would be an odd fit, but I would love to see this engine in some sort of RC "buggy". Great video

Your amazing my man keep this work uo please u showing me alot of ehat i csn try to do

Love the sound and how it shakes lol!!

I love it... would love to have one in my shop to compliment my real Harley shovel head..I would probably build a 1/6 scale with it....military bike with side car....thank you for the review

Even starts like a Harley !!

I came here to hear the Cison engine, but I fell in love with the 'old school clamp'.

lol i watched a screw dance off the bench between the wall and the bench when you started it up :)

Cool little engine.

Haha that’s so neat! It’s like a Harley with the sound it makes. Very nice. Can you also run it on regular gas as well?

Nice, love it 😀

And it’s good to see they don’t have a big fly wheel like the older motor they built that you couldn’t really make it bolt up to scale for a bike

Hey Steve. What would be cool. Is you make a 3 or 4 wheel frame and put that engine in it. Great video man

Wires that go to the crankcase are for a magnetic sensor or optical, red wire positive black negative and white is signal.

Love it

Crazy! A two cycle Shovel...

I have a couple of rc bikes I’d love one of these to make a to scale Harley shovel,so it’s the $500 price in Au? Il try get one at some point wen I’m not broke

I bet that miniature HD engine kicks out more power than the real one,

I've seen everyone on UKposts destroy these out of the box on the first run. They all seem to have ignition problems, the Pan especially. I thought an oil pump was available as an accessory. Fuel mix to me leaves the bottom end dry. I love the looks and like the real thing deserve respect. Properly mounted, better pipes or trim the supplied ones to drag stile. C'mon Steve. Set it up properly. Everyone else on UKposts has destroyed these little wonders straight out of the box. I'd love one and If I could afford one, I wouldn't be wrecking it. Can't wait to see it run well in your hands Steve. 🙏🇦🇺I stand corrected, Johnny has a Panhead running, like you, he has skills.

Runs like an old Harley as well.. I love Harley so need for comments...

I'm no wrench but wont running it without pipes burn out your valves ?

You can use it to built rc Morgan 3-wheeler that's powered by Harley engine.

Very Cool. Now all you have to do is build a rolling frame for it.

It’s almost like cute !

Awesome! If that beast is like every other Chinese metal product, it would benefit from checking all the screws for loctite. That vibration be deadly! What do you think, sell a million because "Harley guys" or is the made in China factor a killer? Gotta think a licensed direct from Harley version would sell in America... maybe even at the double high price required to make it in America

They need to do a Knuckle head next... I think I would take it all apart and balance everything.

They need to make one big enough for a mini bike 👍

I so want one Just have to convince the wife that I need a model harley trike on the shop counter to use as a pencil sharpner. 😆🇦🇺👍

I'm glad I took the time to notice that you make a habit of running these engines straight out of the box with no tuning. Has someone new to this hobby, I think I wouldn't have bothered without that disclaimer. Otherwise the idea of spending 500 bucks on a tiny engine without water cooling and that needs a drill to start it and stalls frequently and is kind of finicky just doesn't seem too smart. But no one's ever accused me of being brightest bulb on the planet, so maybe something like this is in my future after all. Really looking forward to seeing if you can get it to run well and what you did to get it there. There is a fair amount out there on the V1 engine, but hardly any on the V2 yet. My plan is to build it into a vehicle that should be going fast enough to have the air cooling work well enough. I would really want to use regular gas though, because it sounds like Nitro is really expensive and can be tricky to run well consistently, especially during changes of temperature. A couple of questions: 1) you say it will run on gas but I'm imagining you would need different plugs. Do you know which ones those are, and is that all you would need? 2) that toothed gear on the drive shaft looks particularly useful, not only to connect to a propeller or wheels, but also to rig to starter. From the few small engines I've looked at, it looks like many of them can fairly easy accommodate adding an electric starter, I'm wondering if this engine is an exception? 3) I heard somewhere along the way that running an engine too cool can be as bad for it as running it too hot. It would suck to have this engine run lousy or even grenade itself inside for being off on temperature one way or the other. The only idea that comes readily to mind is Jerry rigging an adjustable air barrier to basically lower when the engine is running hotter, and raise when it is getting too cool. Is there a better way of regulating temperature with this kind of engine? Does it say in the manual or do you have an idea as to what the ideal running temperature range of the engine is? Any tips on remote Bluetooth type engine temperature gauges, and where best to put the sensor? To me, either this or the mini engamor (sp?) V8 qualify as the best sounding engines in this hobby. Huge difference in price, but to me they are both pretty expensive for what they are. I don't think I could justify buying either or getting into this hobby at all if I knew at the outset that these engines are really designed to be no more than desktop toys. Either that or they are too difficult or too unreliable to bother integrating into a cool RC vehicle. I know very little about this Hobby. Can anyone care to chime in as to how well these little engines might hold up in a decently designed RC setup, or are they really designed to be nothing more than overpriced desktop noise makers? (regardless of how much I like their sound) I'd love to hear any feedback on any of these observations, either here in the comments or in a future video. Damn it I hate how good these sound and how much of a pain in the ass they're probably going to be if I ever get one, lol.

I need 2, to drive my roller blades🤣👍

Make a small scale Harley bike with that thing man!

wow

I was cringing waiting for it to catch the spark plug wire 😬 Other then that badass!

For a little bit more you can buy a shovel mother and it will start easier and idle better

In a vice! Come on man!

It is very cute

can you build a whole bike though them?

Those pipes are absolutely disgusting . They should put some effort to make a decent pipe for that price. At least microcosm engine looks nicer and mounted on a base

Engines like back pressure you will burn the valves out

Is it °45 ?

The cam is too big🔥💪👍🏻😃

Just like it’s bigger counterparts shakes everything loose and shit.

I wanna put one on my mountain bike.

👍🏾👍🏾👍🏾

Runs like a real shovelhead to.

I’m sure it would run better with exhaust.

Maybe it'll warp an exhaust valve or two before you're smart enough to put the pipes on.

should install it on a motorcycle.

Kind of seemed like she was only running on one cylinder and that may be why it was so violent 🤔🤷‍♂️

I would add a bigger flywheel....

My bet is that is just a two stroke shaped like a shovel head.. no ot dosent sound like a shovel head ..not to my ear ..it sound loud is all .

500th like

Send it too mee. You not need dhis engine…

Giv me

Thanks but horrible work bench, rattles like#

Except for the crankcase it looks more like an ironhead.

Rip off seen the panhead one for 70.00 with free shipping.

Too rich Black smoke

$500 for something that does absolutely nothing??lmfao

Not worth the $700 they want for them, not even close!

Sound horrible.

That huge engine is only 15cc? Shiney paper weight...