Johnny, you should mill out some 1 piece rotors for that blower and open up the ports so it actually flows air.
@technicbuilder641017 днів тому
And if he gave them some twist they would probably be smoother.
@1one3_Racing16 днів тому
There's a reason nobody does forced induction on RC engines. It doesn't work.
@yoda354916 днів тому
real screw/roots blowers have Teflon strips to help seal. i dont know if he could do that too.
@everettstormy16 днів тому
@@1one3_Racing rc airplaned have been using superchargers for a long time lol
@1one3_Racing16 днів тому
@@everettstormy is this an aeroplane?
@WhiskeyGulf7117 днів тому
It stalls sideways because the wheels have stopped turning ! It’s lost its forward momentum, at low rpm you have practically no torque available from the motor, it’s not a diesel engine & you have a huge flat spot in the power.
@andruwmartinez412917 днів тому
I'm sure this has a one way bearing preventing that issue
@chevyman561817 днів тому
@@andruwmartinez4129it stalled In the beginning of the video when he engaged the clutch then had to give it gas to take off running
@rsquared970317 днів тому
It’s a traditional manual transmission. When the clutch is engaged you can’t just stop. I know he put that Revo transmission in but that doesn’t change the direct drive nature of the setup.
@danw195517 днів тому
No, the carbs are losing their prime because there's no tank pressure. The diaphragm pumps on the carbs depend on intake pulses to function, and at high rpm the pulses are too close together to provide sufficient volume. That's why you have run a line from the muffler to pressurize the tank. This is done on a lot of RC planes as well for the same reason.
@jimsimone265116 днів тому
For curiosity sake since I'm not a mechanic or engineer or mechanically incline... would a check valve "back flow preventor" work similar to plumbing applications?
@radweld17 днів тому
You need to ensure the fuel tank remains pressurised by feeding exhaust pressure into it. this way, fuel is always forced into the engine.
@GeomancerHT17 днів тому
Very nice way to blow things up.
@kynghype971517 днів тому
@@GeomancerHT Thats how nitro engines work, do your research lol
@tm512317 днів тому
@@GeomancerHT All RC nitro engines do this, pretty much.
@mattinwinkymg17 днів тому
@kynghype9715 Geomancer probably thinks EGR valves are a good thing too 😂😂
@kleetus9216 днів тому
@@mattinwinkymg Lol... oddly enough I got into an argument with someone about that and PCV systems too!
@filmgunproductions444817 днів тому
The sound never gets old, and hearing it on a moving chassis outside is just fricken amazing
@Kettletrigger17 днів тому
A heavier flywheel may help with the shutoff problem.
@fra572412 днів тому
Why??
@goosebox906411 днів тому
@@fra5724more inertia, but the problem there is it wouldn’t be as rev happy. It should still rev plenty though because it’s a
@fra572411 днів тому
@@goosebox9064 ty
@someonesomewhere_77711 днів тому
It would actually reduce the engine RPM; plus he's already burning out clutches on the flywheel he has, so this might not be a good idea. The comments above about pressurizing the fuel tank with the exhaust is probably an easier solution and won't require any additional modification. Seems to me like the system is losing fuel flow to the dual carb setup in a tilted position which is very indicative of low fuel pressure.
@Kettletrigger11 днів тому
@@someonesomewhere_777 A heavier flywheel will not reduce engine RPM. It WILL slow engine response due to more inertia, which is why a lightened flywheel is a common performance modification. The downside to a light flywheel is a tendency for the engine to lose RPM quickly...sometimes so quickly that it dies. Which is what might be happening here. Slowing engine response will not hurt the clutch. If anything, it will increase clutch life due to more gradual changes in RPM. Johnny has a lathe and a mill - adding weight to the flywheel shouldn't be a big deal (if that in fact is the problem).
@proximo103317 днів тому
That is becoming some serious automotive design, i mean that colling and exhaust, you grow my man!
@waybous17 днів тому
That clicking sound made EVERY car guy wince. Anytime something mechanical makes that noise it's normally not a good thing.
@blueexnetic17 днів тому
The effort and determination of this guy is insane. Every time I see one of your video's in my for you page I don't even hesitate to click on them. I am proud to be one of your 1.87M subscribers!
@HolloMatlala117 днів тому
I am a here as well....Count me in on this comment
@mickgibson37017 днів тому
I myself! I had raced Car, Motorcycle, and RC!
@htothec117 днів тому
100% agreed. This man has the best channel on UKposts. One hell of a smart man
@Gunandgameguy16 днів тому
I have dreamed of seeing a V8 RC car since I was like six thank you for making this I couldn’t stop smiling
@jared910817 днів тому
If you think it’s fuel sloshing make baffles in the tank to reduce the liquid movement. And also the low rpm if you throw the drift tire with a plastic sleeve you can draw your conclusion of fuel loss and or rpm being to low
@CptDallas17 днів тому
Review how gas RC PLANES do it. They go inverted and still have power.
@FSShenanigans16 днів тому
Full size car our fuel cell has foam in it to prevent sloshing may be easier than making baffles
@dylancoventry912217 днів тому
I’ve been watching since you got the V8 and I’m stoked to see it driving and skidding around bro, well done 🙏
@giorgoskaras539916 днів тому
Φίλε Έλληνας είσαι σε βλέπω τόσο καιρό και δεν με πήγε ο νους ότι είναι Έλληνας. Μπράβο ρε φίλε συγχαρητήρια, τέλεια βιντεάκια
@panosbosst417616 днів тому
Φίλε και εγώ έπαθα πλάκα τον βλαιπω πάνω από 2 χρόνια και δεν μου είχε περάσει ποτέ από το μυαλό 😮
@user-rp8zv8nl6n11 днів тому
Ναι ισχύει παιδιά ο τύπος είναι πολύ μυαλό!
@thegarynator16 днів тому
This thing is so dang cool! Thanks for sticking with it and continuing to share!
@johnkilo317 днів тому
At first I was worried JohnnyQ90 wasn't devulging that he is sponsored by Toyan or Sterling Kit, and that he actually gets all these engines for free. You're supposed to let people know if you're sponsored. To be honest, though, I think these videos have made me want these small engines less and less the more of them I see. Imagine spending $1700 on this "supercharged" V8, plus everything else needed to get it to run (and even more if in an RC chassis), and the thing just breaks almost immediately because of terrible manufacturing and tolerances. I'll stick with enjoying watching someone else spend tons of money on getting them to work right.
@OhHeyItsBilly17 днів тому
I don't mind he's sponsored or not. I love the creative process in his videos. I think he does a great job. I love watching all of the unique machining parts and 3D printed parts. Those engines seem on the surface really awesome but I can tell they break catastrophically really easy, the tolerances in the machining process are probably not good at all even though it "looks" good. Being sold extra attachments like superchargers that actually hinder and hurt the motor instead of actually giving more power. You would have to have a bunch of expendable income and enjoy this as a hobby because these motors seem like they're really low quality and horribly made and unreliable.
@johnkilo315 днів тому
@@OhHeyItsBilly I don't mind if he's sponsored either, but you're supposed to disclose it.
@Man9482414 днів тому
bit rude i do say
@ThatOneGuyWithTheEye9 днів тому
You can literally buy a real roadworthy car with a real motor for that price. Most of mine have cost less
@austinkoeppen612216 днів тому
I'm just impressed with how well it starts, I've seen lots of others struggle with these.
@mikellewis234617 днів тому
Best v8 rc ive seen running an driving so far on UKposts....❤
@17111993DAVE16 днів тому
I bet youre so happy to see it coming together. I know your viewers are. Way cooler than normal RC cars nitro or battery. Well done.
@doranjohnson536515 днів тому
This dude and these builds inspire me to go learn how to do stuff. So freaking cool. Thanks for documenting this for us, Johnny!
@adamdiaz844214 днів тому
I bet that felt great getting it out for a spin congrats bud awsome work
@lhionaleobary258216 днів тому
its been more than 2 years followed you and i'v seen this little thing grew and now its 90% finished i am so proud of you. gg and continue let's go to the 2mill
@rcOhio17 днів тому
Great test drive! It sounds so good! Thanks for sharing JQ90!
@Evans_Man12 днів тому
Δεν περίμενα ότι θα έβλεπα τέτοιο διαμαντάκι στην πόλη μου! Πολλά συγχαρητήρια!
@lordbunny241617 днів тому
U could cut a two slots into the metal, to maintain balance of the clutch and into the friction material, and use two dowel pins plus a lil glue to keep it from delaminating!! Just a thought!! Keep it up, love the Vidz!!!!
@AngelLuisTrinidad17 днів тому
I will like to shrink myself so I could drive it. Dispite the repairs it needs I still find it perfect and awesome. Great work Johnny.
@tuna346116 днів тому
That sounds awesome dude holy fuck. This is like the next level in realism. Hearing it pass you even at those low speeds is insane
@tuna346116 днів тому
How loud is it? Is it painfully loud like a typical nitro engine?
@mattculpepper644416 днів тому
Awesome video as always, Sir. Long time subscriber. As an American, I always love seeing a fire breathing V8, in any form. I hope you can get the blower figured out. Keep up the great work Mr. Q90!
@TheYetiSlayer9 днів тому
That's absolutely epic!!! Great job man!!🙌🏻👏🏻
@richardoeser564315 днів тому
Sick! Love seeing them drive and operate
@mohammadaminranjbar900817 днів тому
very exciting V8 sound! great work!
@laurentdarcq562417 днів тому
Amazing ! Superb ! Congratulations !
@Dingle-Berries11 днів тому
This guy is smart and clever to figure it out, he knows his car well. Dude built it from scratch
@brettc538617 днів тому
I've been waiting for this video for so long and I'm glad it's finally here. But also I can see it needs some refinements in the power band, especially in the low rpm, knowing your potential it would be amazing to see you make turbos like you did for the twin cylinder 4-stroke, but have two different sized turbos and connect them in a compound setup so that way you can get the most torque down low and horsepower up high.
@user-pd1vg1qq1x15 днів тому
creating a body for the car once it is mechanically sound would be so cool! , it would literally be a mini car! , great vid once again!
@flashforum93917 днів тому
What a sweet ride - love the sound
@NoobAlike17 днів тому
glad to see it finally roam free on the ground! all that work!
@just.jose.youtube16 днів тому
Thank you good sir for making our dreams come true! 🙏🙏🙏 A V8 RC... 😍 What a great set if skills you have!
@Dollfin3410 днів тому
This thing is so sick, can’t wait to see the final version
@joequashnock15529 днів тому
So exciting to see that beast off the chain and thrashing about! Just like any scratch built DIY project, things are going to happen. I have 100% faith that you will work out the bugs. Looking forward to the next update!!
@joshuasterling21449 днів тому
It seems like there is a lot of hope for this project to actually come all the way through. Looking great so far and I can see it getting the last 25 percent improvement and then it probably will be the best rc car of its type on UKposts. It starts, the throttle is responsive and its fast enough to warrant the effort.
@auwz6617 днів тому
Excellent stuff! I think you might benefit from a baffle or two (or foam) in your fuel tank.
@atishayajain186217 днів тому
This thing's gonna burn some rubber 🔥🔥🔥
@slyknezz686217 днів тому
Very Cool!!! Such a unique sound for an rc!
@bigdadgigachad304217 днів тому
CONGRATS 🎉👏🏆
@shize9ine17 днів тому
im excited to see you make alloy rims next ep!
@jaybomb502217 днів тому
Pulling air bubbles into the fuel line. Add a splitter with 2 inlets inside the tank. Or a piece of fuel filter foam to stop the sloshing.
@jrtate112314 днів тому
It sounds cool as hell 🤙🏽
@Tyblerone8 днів тому
Dude these videos are so friggin' cool.
@gavriilk744014 днів тому
Μπράβο φίλε , Πάχη Συνέχισε έτσι, Και πάλι μπράβο 👍🇬🇷
@emerilnut17 днів тому
Sweet! So glad you're at the testing phase. I've been watching the build process and am REALLY IMPRESSED! I don't know if anyone has mentioned it yet or I may grant forgotten if you already thought about this, but have you implemented some runaway protection? You know, how to make the car stop if it loses contact with the radio while under full throttle. Always an issue with nitro RC cars.
@Shadow0fd3ath2416 днів тому
thing sounds SOOO good man! Id go to a positive pressure fuel system like nitro cars run normally where it gets some exhaust air to pressurize it
@GavinY15 днів тому
The sound is so good
@christopherlenahan390617 днів тому
My guess is rotor shaft flex and the tolerances of the supercharger synchro gears: -That tri-lobe rotor looks to be a 3D ratio, with 3 segments I doubt it has the rigidity to stay straight under boost. -The synchro gears would need to have insanely tight tolerances and sub tenth backlash to maintain the lobe seal with such small gears/rotors. Even operating with a wet seal design. -If you do decide to make your own rotors, may I suggest a helical tri-lobe.
@shkiper422417 днів тому
Sounds awesome !
@holdmybeer393117 днів тому
It’s getting faster and more responsive 👍
@antoniskotis52087 днів тому
Then start from control is very important and awesome
@mafroh473315 днів тому
I can't wait to hear it tuned!
@TRFH117 днів тому
stalling- could be fuel pickup location on your tank you are using, also can play with the length of the hose from the exhaust to the tank to help keep constant pressure in the tank.
@EJ-7413 днів тому
So awesome to see it driving...
@justmechanicthings7 днів тому
Wonderful progress Johnny sounds like a nascar
@Whateverpoopiepants17 днів тому
Maybe machine the rotors in the supercharger to accept some Teflon blades. Like in top fuel dragsters. ❤
@3dpoolslandscapedesignsbyr83011 днів тому
first time ive ever seen somone actually do work other than idle, great job! looks like a better application would be a monster truck or rock crawler
@Darcho1317 днів тому
It has a terrible understeer, the car doesn't want to turn. And if you apply too much power, it immediately oversteers. I suggest you check your differential (if exists) . This issue causes extra load to your engine and clutch while turning. The car came from a long way, and I love how you build it with great effort and create quality content. Keep on, friend across the pond!
@MartyGramRC15 днів тому
@JohnnyQ90 - just a thought: set up the throttle and clutch actuations on the same servo (or multiple servos from the same channel) - as you give it more throttle, the clutch starts to engage, and as you let off, the clutch disengages. This would take an incredible amount of fine tuning, but I’d imagine would work extremely well, but still provide that realistic functionality you’re looking for.
@UnitSe7en16 днів тому
It has a very realistic, very scale look to it's speed, power and stance.
@jayhow99717 днів тому
For the clutch how about making a flat flywheel and using mountain bike hydraulic disc brake pads as clutch pads using that pivot you already got to push 3 or 4 pads against a flywheel.
@justdontlook0116 днів тому
Using the exhaust to pressurize the fuel tank is good. Putting partitions with small holes into the fuel tank might help with stalling when sideways. that way the fuel doesn't slosh around as much.
@Pelmen.Nik503117 днів тому
Круто получилось, осталось только корпус подобрать и будет пушка 👍
@mrluken-official17 днів тому
This thing sounds good!
@RJ-wy6cx22 години тому
That is absolutely awesome😮
@TheBeetle717 днів тому
Ein Geiles teil, super Arbeit .
@danw195517 днів тому
The comment about the tank needing to be pressurized is correct. They flow a lot of fuel at WOT, and the diaphragm pumps in the carbs can't keep up with it unless you have some tank pressure. You might look into sintered bronze for your clutch basket. The hotter it gets, the better it works. You may need a bit stronger return spring though.. Other than that, pretty good run for the 'first' time out!!😄👍👍
@mattbellina548513 днів тому
Really freaking awesome!
@stevensims33428 днів тому
Need a locking slot or slots for the clutch lining or something. Really neat project!
@letsdosomething669117 днів тому
I agree with a lot of these comments about the stalling issue. I’m leaning towards the idea that was mentioned about the clutch being still engaged while the car comes to a complete stop. That would definitely stall my car at least. That also probably played a roll in the clutch breaking. If it’s a fuel issue though, my suggestion is try a bigger fuel line, and a carb bowl if they don’t already have one. The bigger line will keep it from hydro locking, and the bowl will help with whatever air still gets through. As for the super charger I’m on team solid rotors lol. Those have to be one, solid, smooth piece to get rid of the slap. They have way too much wiggle being three pieces each. In other news; line lock? Totally unnecessary and would probably destroy the transmission but man would it be cool if it worked. Just sitting there roasting the tires and then turning it off and peeling away. As always, love the video. Keep up the awesome work, and I can’t wait for the next one.
@phildavis128217 днів тому
Keep it up johnny your just too cool 👍
@vincentoden862517 днів тому
i think part of the reason it stalls when u slide is causee the engine just doesent have enough energy to keep going when the wheels slow down after a slide. real cars do the same if u spin and dont disengage the cluch
@dfgaJK17 днів тому
sounds sooo good!
@applesbighatranch690614 днів тому
Sounds much better sans blower. I wanna hear it through 180* headers. Thanks for the vid.
@Pigpin1317 днів тому
That thing sounds so mean. Love it
@TheOfficial_InsaneStang17 днів тому
Dude, ya got this!!! 🤘😎
@projectcar948817 днів тому
About time! Make it run alrwady
@benjammin307810 днів тому
Amazing totally 👍 on board with your drive in making outer perfection on a machine that’s thrills the senses of WOWness in the ability to create kudos to you bro 🎉🎉🎉🙏👍
@triynizzles16 днів тому
I would love to see new rotors for the supercharger!! There's so many videos out there with little superchargers and turbochargers for micro engines like this and none of them ever work. it's so sad I want to see one that works. you can do it!!
@raulbustamante833712 днів тому
The sound is brutal
@NefariousStrudel16 днів тому
through some dowels through the rotors so they stay put. thread the ends so you can secure them. It might help the rotors not contact the housing since it won't be able to deform the aluminum at high rpm.
@MDBenson16 днів тому
I'd add a baffled fuel cell to the list too, maybe put some foam in there and or make something custom with a baffled swirl pot built into it, the sort of thing you see on drag cars. The sudden direction changes and inertia were visibly causing the fuel to climb up the side of the tank which as the fuel goes down are probably starving the feed line.
@rjansen687417 днів тому
I think a 7.5cc nitro engine 1 cilinder wil outperform all those toyan engines. Sad but treu. I still love it that you try making them work!!😍
@ethanssmallengines325315 днів тому
You could make a custom fuel tank with baffles on the inside to prevent the fuel from sloshing to either side. Cheers!
@NonEuclideanTacoCannon17 днів тому
It would be interesting to spin the supercharger at operating RPM without the engine, to see how much air it moves. I think these tiny engines are too small for forced induction to work properly. And I think the tolerances are probably just good enough for them to run, I think any substantial level of boost would bend things or just end up being lost as blow by. I'd love to be proven wrong, though. "2 Stroke Stuffing" gets an astounding amount of power out of a 50cc engine, but that's only one cylinder, and it's actually designed for vehicular use.
@shadowcustomaudio56547 днів тому
If you add a pressurized fuel rail system with like even 2 or 3 psi it would prevent it from shutting off when starved of fuel. I noticed its fuel delivery when it didnt fully die after turning and when you throttled it, it was already leaning out and it was to lean to get the fuel to create combustion again.
@stevejackson356417 днів тому
Don't know if it does anything, but I like the high pich sound it makes
@demantoid41817 днів тому
Sick. 😯 You are getting close. She is going to rip. Thanks for letting us come along. 🫡
@sch0neDK17 днів тому
Nice to see it driving :-)
@jz6410 днів тому
Badass good work
@danielnygard16 днів тому
Dude is the Mozart of RC builds
@schrodingersmechanic762217 днів тому
Sounds like a Yamaha R1. Sick!
@mrvector25717 днів тому
The scoring on the inside of the supercharger housing looked like it was towards the center, so the rods holding the rotors might be bowing from a slight imbalance when they spin fast enough. Someone mentioned one-piece rotors, so that might help a rigidity issue. If that's what's actually happening.
@kmatch117 днів тому
A felt or ceramic fuel clunk may help if fuel is aerating or sloshing air causing it to die.
@flodar154816 днів тому
Great job
@clive450017 днів тому
I'm glad that you looked at that supercharger.... Very difficult on small-scale to get any form of pumping efficiency... Ratio of size 2 clearance.. Plus friction of the belt... but perhaps you could just run the supercharger with a motor and measure the pressure at different RPMs..... As well as getting an idea of the flow rate...before connecting it back to the engine...